Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for XAVI Technologies Corp. X7721r
Summary of Contents for XAVI Technologies Corp. X7721r
- Page 1 X7721r/X7721r User’s Manual Version 1.0 - 1 -...
- Page 2 X7721r/X7721r User’s Manual Version 1.0 XAVi Technologies Corporation Tel: +886-2-2995-7953 9F, No. 129, Hsing Te Road, Sanchung City, Taipei Hsien 241, Taiwan Copyright © 2003, XAVi Technologies Corporation Information in this manual is subject to change without notice. No part of this manual...
-
Page 3: Table Of Contents
X7721r/X7721r User’s Manual Version 1.0 – – Overview…………………………………….………….……….……… 6 Features…………………………………………………………..…….. 7 III. Packaging……………………………………….…….………………… 8 Safety Guidelines………………………………………………………. 9 Appearance…………………………………..………………….…….. 10 Front Panel…………………………………………………….……..…10 Rear Panel………………………………………………………..…… 11 Hardware Installation…………………………………………………. 12 VII. Management…………………..………………..…..…….…………... 13 VIII. Default Values…………….……..……………………………………. 14 Software Upgrade……………………..……………………………… 15 – – Console Setup..…………….………….………………..….…..…….. 17 CLI Commands……...……………………………..…………………. - Page 4 X7721r/X7721r User’s Manual Version 1.0 3.4.4 Policies, Triggers, Intrusion Detection..…………….44 3.4.4.1 Security Policy Configuration……………….45 3.4.4.2 Security Triggers…………….……………….49 3.4.4.3 Intrusion Detection…………..……………….50 3.4.4.4 Default Security Policies…………………….51 System Settings………………………………………………….. 52 4.1 Local LAN IP………………………………………………… 52 4.2 DHCP Server……………………………………………….. 53 4.3 Management………………………………………………… 54 4.3.1 Edit User Details…………….……………………...
- Page 5 X7721r/X7721r User’s Manual Version 1.0 Revision Marks Revision Date Notes V 1.0 December 12, 2003 Software Version: 1.02XAT0.7721A - 5 -...
-
Page 6: Overview
Chapter 1 Getting Started Overview The X7721r/X7721r is a multi-mode ADSL/ADSL2 router, which complies with ANSI T1.413 Issue 2, ITU G.992.1 (X7721r/X7721r ITU G.992.2, G.992.3, G.992.4, G.992.5 (X7721r only), Annex A, and ETSI ITS 101388 ADSL standards. The X7001r supports ADSL2 as well. -
Page 7: Features
X7721r/X7721r User’s Manual Version 1.0 Features High Speed Asymmetrical Data Transmission on Twisted Copper Pair Wire Service providers can deploy ADSL rapidly over existing wire infrastructure (POTS or ISDN line) Interchangeable between Bridge and Router mode RFC 1483 Bridge and Routing over ATM over ADSL... -
Page 8: Packaging
X7721r/X7721r User’s Manual Version 1.0 III. Packaging This package consists of the following items: X7721r/X7721r ADSL device unit RJ-45 Cable RJ-11 Cable AC Adapter User’s Manual CD - 8 -... -
Page 9: Safety Guidelines
X7721r/X7721r User’s Manual Version 1.0 IV. Safety Guidelines In order to reduce the risk of fire, electric shock and injury, please adhere to the following safety guidelines. Carefully follow the instructions in this manual; also follow all instruction labels on this device. -
Page 10: Appearance
X7721r/X7721r User’s Manual Version 1.0 V. Appearance Front Panel Label Color Description Status 100M Green 100M Ethernet transmitting. Green 10M Ethernet transmitting. Green Power supply is connected. Blinking Green Training with DSLAM. Green ADSL link is ready. Blinking Booting up. -
Page 11: Rear Panel
X7721r/X7721r User’s Manual Version 1.0 Rear Panel Label Description Power jack; connect to a power adapter. ETHERNET RJ-45 port; connect to a PC or LAN. RESET Reset the modem back to factory settings by holding down on this button. RJ-11 port; connect to the ADSL outlet. -
Page 12: Hardware Installation
X7721r/X7721r and the other end to the ADSL wall outlet. 2. Use a RJ-45 cable to connect one end to the Ethernet port of X7721r/X7721r and the other end to the LAN or a PC with an Ethernet adapter installed. -
Page 13: Management
X7721r/X7721r User’s Manual Version 1.0 VII. Management Console Port – use the RS-232 cable for connecting X7721r/X7721r to a console terminal or a PC running a terminal emulation program, such as Hyper Terminal. (For further details, See Chapter 2: Command Line Interface) Local Ethernet Port (telnet) –... -
Page 14: Default Values
X7721r/X7721r User’s Manual Version 1.0 VIII. Default Values X7721r/X7721r is pre-configured with the following parameters; you may also re-load the default parameters by typing Restore in the command line interface or using the Restart link in the Web interface. Default Mode: Bridge... -
Page 15: Software Upgrade
Software upgrade through a DOS prompt Step 1. Extract the ZIP file for updated firmware. Step 2. Connect X7721r/X7721r via the local Ethernet port or remote ADSL link, making sure that the X7721r/X7721r Ethernet IP address and your terminal are properly configured that successfully “ping”... - Page 16 Software upgrade through a Web-browser Step 1. Extract the ZIP file for updated firmware. Step 2. Connect X7721r/X7721r via the local Ethernet port or remote ADSL link, making sure that the X7721r/X7721r Ethernet IP address and your terminal are properly configured that successfully “ping”...
-
Page 17: Console Setup
Double Click “Hypertrm.exe” Enter a Connection Name Select Icon Click OK 2. Select a COM port to communicate with X7721r/X7721r Choose Direct to COM1 or Direct to COM2 and click on OK 3. Set Port Properties Port Setting: Bit per second: 9600... -
Page 18: Cli Commands
X7721r/X7721r User’s Manual Version 1.0 III. CLI Commands Main Menu Commands Type “?” following the “→” to retrieve a list of commands under the main menu to begin the configuration. Command Syntax Description / Parameters → display Display Displays the configuration of IP →... - Page 19 X7721r/X7721r User’s Manual Version 1.0 RESTART Restarts the modem. Syntax: restart → restart NBfs1Z PP Boot 9.0.3.19 (28 July 2003) Copyright (c) 2003 GlobespanVirata, Inc. SDRAM size = 0x1000000 i 13% i 17% i 22% i 27% i 31% i 36%...
- Page 20 X7721r/X7721r User’s Manual Version 1.0 RESTORE Sets all configurations to factory default settings. Syntax: restore restore → Restoring factory defaults... → PING Pings a specified IP address. Syntax: ping <ipAddress> Example: ping 192.168.0.81 → ping 192.168.1.1 ping: PING 192.168.1.1: 32 data bytes ping: 40 bytes from 192.168.1.1: seq=0, ttl=128, rtt<10ms192.168.0.81...
-
Page 21: Lan Menu Commands
Command Syntax Description / Parameters setip lan→ setip Configures IP settings <ipAddresss> [<subnet mask>] SETIP Configures the IP address and subnet mask of X7721r/X7721r Syntax: setip <ipaddress>[<subnet mask>] Example: setip 192.168.1.10 255.255.255.0 setip 192.168.1.10 255.255.255.0 lan> lan> - 21 -... -
Page 22: Ii. Preparation
Example: X7721r/X7721r : 192.168.1.1 Your PC: 192.168.1.x 3. Connect your PC to X7721r/X7721r and make sure that the PING function is working properly. The default IP address of this device is 192.168.1.1 4. Launch the Web browser (IE or Netscape), and enter the default IP address 192.168.1.1 into the address bar to... -
Page 23: Login
X7721r/X7721r User’s Manual Version 1.0 1. Login The Enter Network password window will pop up when starting the configuration. With the window active, type admin for both User name and Password, and then click on the OK button. You can also edit the username and password or add a new profile (see section 4.3 Management for further details). -
Page 24: Connection Settings
X7721r/X7721r User’s Manual Version 1.0 2. Connection Settings Click on the Connection Settings link on the navigation bar. This page lists the WAN connection protocols that are available on this device. Please read the following instructions for creating each type of WAN connection. -
Page 25: Rfc 1483 Bridge
X7721r/X7721r User’s Manual Version 1.0 2.1 RFC 1483 Bridge Click on the Create new connection service link to display the types of service available. Select RFC1483 Bridge and then click on the Go to next step button. - 25 -... - Page 26 X7721r/X7721r User’s Manual Version 1.0 You will then see the following screen: VPI: Enter the VPI value into this box. VCI: Enter the VCI value into this box. Qos: Select the quality of service level from the menu Encapsulation: Select LLC or VC-Mux from the menu.
-
Page 27: Rfc 1483 Bridge With Nat
X7721r/X7721r User’s Manual Version 1.0 2.1.1 RFC 1483 Bridge with NAT Click on the Create new connection service link to display the types of service available. Select RFC 1483 Bridge and then click on the Go to next step button. - Page 28 X7721r/X7721r User’s Manual Version 1.0 You will then see the following screen. Be sure to select RFC1483 Bridge with NAT for Connection type. VPI: Enter the VPI value into this box. VCI: Enter the VCI value into this box. Qos: Select the quality of service level from the menu Encapsulation: Select LLC or VC-Mux from the menu.
-
Page 29: Rfc 1483 Route
X7721r/X7721r User’s Manual Version 1.0 2.2 RFC 1483 Route Click on the Create new connection service link to display the types of service available. Select RFC 1483 Route and then click on the Go to next step button. - 29 -... - Page 30 X7721r/X7721r User’s Manual Version 1.0 You will then see the following screen: VPI: Enter the VPI value into this box. VCI: Enter the VCI value into this box. Qos: Select the quality of service level from the menu. Encapsulation: Select LLC or VC-Mux from the menu.
-
Page 31: Ppp Over Atm (Pppoa)
X7721r/X7721r User’s Manual Version 1.0 2.3 PPP over ATM (PPPoA) Click on the Create new connection service link to display the types of service available. Select PPP over ATM and then click on the Go to next step button. - 31 -... - Page 32 X7721r/X7721r User’s Manual Version 1.0 You will then see the following screen: VPI: Enter the VPI value into this box. VCI: Enter the VCI value into this box. Qos: Select the quality of service level from the menu. Authentication: Select PAP or CHAP.
-
Page 33: Ppp Over Ethernet (Pppoe)
X7721r/X7721r User’s Manual Version 1.0 2.4 PPP over Ethernet (PPPoE) Click on the Create new connection service link to display the types of service available. Select PPP over Ethernet and then click on the Go to next step button. - 33 -... - Page 34 X7721r/X7721r User’s Manual Version 1.0 You will then see the following screen: VPI: Enter the VPI value into this box. VCI: Enter the VCI value into this box. Qos: Select the quality of service level from the menu. Authentication: Select PAP or CHAP.
-
Page 35: Ip Over Atm (Ipoa)
X7721r/X7721r User’s Manual Version 1.0 IP over ATM (IpoA) Click on the Create new connection service link to display the types of service available. Select IP over ATM and then click on the Go to next step button. - 35 -... - Page 36 X7721r/X7721r User’s Manual Version 1.0 You will then see the following screen: VPI: Enter the VPI value into this box. VCI: Enter the VCI value into this box. Qos: Select the quality of service level from the menu. DHCP Client: Check this box if you would like the device to receive its IP address from a DHCP server (if you select this option, you do not need to enter an IP address or subnet mask).
-
Page 37: Advanced Settings
X7721r/X7721r User’s Manual Version 1.0 3. Advanced Settings Click on the Advanced Settings link on the navigation bar. This section includes NAPT (Network Address Port Translation), Static Routes, and DNS Relay. Each section is described in detail below. 3.1 NAPT (Network Address Port Translation) Click on the NAPT link in the navigation bar to view the NAPT configuration page. -
Page 38: Static Routes
X7721r/X7721r User’s Manual Version 1.0 You may map a port to an interface by clicking on the Add Reserved Mapping link under the Disable NAT to internal interfaces button. You will then see the following screen: Internal IP Address: Enter the IP address to which you would like to map a protocol and port. - Page 39 X7721r/X7721r User’s Manual Version 1.0 You will then see the following screen: Destination: Enter the IP Address of the destination router. Gateway: Enter the IP Address of the gateway. Mask: Enter the subnet mask of the IP address. Metric: Enter the number of hops required to reach the destination.
-
Page 40: Dns Relay
X7721r/X7721r User’s Manual Version 1.0 3.3 DNS Relay Click on the DNS Relay link in the navigation bar to view the DNS Relay table. Enter the Primary DNS address into the text box and then click on the Apply button. -
Page 41: Security
X7721r/X7721r User’s Manual Version 1.0 3.4 Security Click on the Security link in the navigation bar to view or change the security interface settings. 3.4.1 Security State Use the toggle switch to enable or disable Security, Firewall, and Intrusion Detection. -
Page 42: Security Level
X7721r/X7721r User’s Manual Version 1.0 3.4.2 Security Level You must set Firewall to Enabled in order to choose a security level. Choose a value for Security Level from the drop-down menu. Click on the Change State button to apply the new settings. -
Page 43: Security Interfaces
X7721r/X7721r User’s Manual Version 1.0 3.4.3 Security Interfaces This table lists the name, type, and NAT status of each security interface. To enable NAT on an interface, click on the Enable NAT to internal interfaces button. To disable NAT on an interface, click on the Disable NAT to internal interfaces button. - Page 44 X7721r/X7721r User’s Manual Version 1.0 Add Reserved Mapping Internal IP Address: Enter the IP address to which you would like to map a protocol and port. Transport Type: select a protocol from the drop down list. Port: Enter a port number for the selected protocol.
-
Page 45: Security Policy Configuration
X7721r/X7721r User’s Manual Version 1.0 3.4.4.1 Security Policy Configuration To add a new security policy, choose the Security Policy Configuration link, and then choose the New Policy link on the next screen. You will then see the following screen: Choose the types of interfaces from the menus between which you would like to configure the security policy. - Page 46 X7721r/X7721r User’s Manual Version 1.0 Port Filters To set the port filters, click on the Port Filters link in the Current Security Policies table. On the next screen, choose Add TCP or UDP Filter or Add Raw IP Filter link depending on the type of filter you want to create.
- Page 47 X7721r/X7721r User’s Manual Version 1.0 Add Raw IP filter Enter the criteria for the port filter into the table. Default values for “allow” criteria will allow all traffic to pass (as shown in this example). Default values for “block” criteria will block all traffic.
- Page 48 X7721r/X7721r User’s Manual Version 1.0 Host Validators To set the host validators, click on the Host Validators link in the Current Security Policies table. On the next screen, choose the Add Host Validator link . You will then see the following screen: Enter the IP Address and subnet mask for the host that you want to have validated.
-
Page 49: Security Triggers
X7721r/X7721r User’s Manual Version 1.0 3.4.4.2 Security Triggers Security triggers can be defined on the following interfaces: External and internal External and DMZ DMZ and internal To add a new security trigger, choose the Security Trigger Configuration link, and then choose the New Trigger link on the next screen. -
Page 50: Intrusion Detection
X7721r/X7721r User’s Manual Version 1.0 3.4.4.3 Intrusion Detection Intrusion detection can be defined on any interface with an external endpoint. To configure firewall intrusion detection, choose the Configure Intrusion Detection link. Firewall intrusion detection can be configured only if Intrusion Detection is enabled in the Security State section. -
Page 51: Default Security Policies
X7721r/X7721r User’s Manual Version 1.0 3.4.4.4 Default Security Policies Default security policies, including port filters and security triggers, are defined for the low, medium, and high security levels. For example, if the High security level is selected, security policies for every type of interface are already defined, as shown below. Each security policy applies only if its corresponding interface is defined by the user. -
Page 52: System Settings
X7721r/X7721r User’s Manual Version 1.0 System Settings Click on the System Settings link on the navigation bar. This section includes Local LAN IP, DHCP Server, Management, and ADSL. Each section is described in detail below. 4.1 Local LAN IP Click on the Local LAN IP link in the navigation bar to view the LAN IP table. -
Page 53: Dhcp Server
X7721r/X7721r User’s Manual Version 1.0 4.2 DHCP Server Click on the DHCP Server link in the navigation bar to view the DHCP Server settings. This device can be set up to perform the service of a DHCP Server and enables data connection between multiple PCs through the configuration of IP address ranges and lease times. -
Page 54: Management
X7721r/X7721r User’s Manual Version 1.0 4.3 Management Click on the Management link in the navigation bar to view the user login details. Here you may edit user login details or add/delete users. Each item is described below. 4.3.1 Edit User Details Click on the Edit link to change the settings of the admin user. -
Page 55: Add Users
X7721r/X7721r User’s Manual Version 1.0 4.3.2 Add Users Click on the Create new user link to add a user. On this page you may fill in the details for the new user. Username: Enter a new username for the new user. -
Page 56: Delete Users
X7721r/X7721r User’s Manual Version 1.0 4.3.3 Delete Users In order to delete an existing user, click on the Delete link next to the user’s name. You will then be asked to confirm if you would like to delete this user. Click on the Delete this User button. -
Page 57: Ethernet
X7721r/X7721r User’s Manual Version 1.0 4.4 Ethernet Click on the Ethernet link on the navigation bar. This page displays a table of the default Ethernet settings. This includes port, configuration, linked status, and speed/duplex. You can choose a value for speed/duplex from the drop-down menu. - Page 58 X7721r/X7721r User’s Manual Version 1.0 - 58 -...
-
Page 59: Modem Status
X7721r/X7721r User’s Manual Version 1.0 5. Modem Status Click on the Modem Status link on the navigation bar. You will then see the following page. Listed on this page are the port connection status, LAN status, WAN status, ADSL status, and device status. - Page 60 X7721r/X7721r User’s Manual Version 1.0 LAN Status: This table displays the LAN IP address, and indicates whether this device is used as a DHCP server. Click on the Detail… link to view the LAN statistics. This page displays the MAC address and transfer statistics.
-
Page 61: Maintenance
X7721r/X7721r User’s Manual Version 1.0 6. Maintenance Click on the Maintenance link on the navigation bar. This section includes Error Log, Modem Upgrade, Backup/Restore, Restart and Save. Each section is described in detail below. 6.1 Error Log Click on the Error Log link in the navigation bar to view the history of errors. -
Page 62: Modem Upgrade
X7721r/X7721r User’s Manual Version 1.0 6.2 Modem Upgrade Click on the Modem Upgrade link in the navigation bar to view the modem upgrade page. Click on the Browse button to select the upgrade file. Click on the Update button when completed. -
Page 63: Restart
X7721r/X7721r User’s Manual Version 1.0 6.4 Restart Click on the Restart link in the navigation bar to view the restart page. To restart the modem, click on the Restart button. You may also check the Reset to factory default settings box if you would like to restart the modem with the factory settings. -
Page 64: Appendix A - S P E C I F I C A T I O N S
X7721r/X7721r User’s Manual Version 1.0 – – A1. Hardware Specifications Local Interface • Type – 10/100BaseTX Ethernet, IEEE 802.3 • Connector – RJ-45 WAN ADSL Line Interface • Compliant with ADSL ITU G.992.1, G.992.2, G.992.3 and ANSI T1. 413 Issue 2 •... -
Page 65: A2. Software Specifications
X7721r/X7721r User’s Manual Version 1.0 A2. Software Specifications • ATM Cells over ADSL, AAL5 • Bridge mode: Supports 8 PVCs • Router mode: Supports 5 PVCs • Supports UBR, CBR, VBR-nrt, and VBR-rt • ATM Forum UNI 3.0, UNI 3.1, UNI 4.0 •... -
Page 66: B1. Product Warranty
X7721r/X7721r User’s Manual Version 1.0 Appendix B – Warranties B1. Product Warranty XAVi Technologies warrants that the ADSL unit will be free from defects in material and workmanship for a period of twelve (12) months from the date of shipment. -
Page 67: B2. Warranty Repair
X7721r/X7721r User’s Manual Version 1.0 B2. Warranty Repair 1. During the first three (3) months of ownership, XAVi Technologies will repair or replace a defective product covered under warranty within twenty-four (24) hours of receipt of the product. During the fourth (4th) through twelfth... -
Page 68: Appendix C - Regulations
X7721r/X7721r User’s Manual Version 1.0 Appendix C – Regulations C1. FCC Part 15 Notice Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 to the FCC rules. -
Page 69: C2. Ic Cs-03 Notice
X7721r/X7721r User’s Manual Version 1.0 C2. IC CS-03 Notice The Industry Canada label identifies certified equipment. This certification means that equipment meets certain telecommunications network protective, operational, and safety requirements as prescribed in appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee that the equipment will operate to the user’s... -
Page 70: C3. Ul Safety Regulations
X7721r/X7721r User’s Manual Version 1.0 C3. UL Safety Regulations Disconnect TNV circuit connector or before removing cover or equivalent. Disconnect TNV circuit connector(s) before disconnecting power. Do not use this product near water for example, near a bathtub, washbowl, and kitchen sink or laundry tub, in a wet basement, or near a swimming pool. -
Page 71: Contact Information
X7721r/X7721r User’s Manual Version 1.0 Contact Information You can help us serve you better by sending us your comments and feedback. Listed below are the addresses, telephone and fax numbers of our offices. You can also visit us on the World Wide Web www.xavi.com.tw...