JumpSport 120 Assembly & Installation Manual

Safety enclosures
Hide thumbs Also See for 120:

Advertisement

Quick Links

Alternate Assembly Instructions for
Models 120, 280, 380, 480, and 480XT
Assembly, Installation, Care, Maintenance, and Use
DO
somersaults.
head or neck can cause serious
injury, paralysis or death, even
when landing in the middle of the
bed.
DO NOT attempt to jump over
the barrier.
Retain address information for future use.
JumpSport, Inc.
2055 South 7th Street, Suite A
San Jose, CA 95112 U.S.A.
Safety Enclosures
Instructions
WARNING
Read these materials prior to assembling and
using this Trampoline Enclosure
NOT
attempt
or
Landing
on
Use trampoline only with mature, knowledgeable supervision.
allow
the
1
DO NOT allow more than one
person inside the trampoline
enclosure. Use by more than
one person at the same time
can result in serious injury.
DO NOT intentionally rebound
off the barrier.
DO NOT hang from, kick, cut
or climb on the barrier.
The maximum user weight is:
Model 280: 200 pounds
Model 120 & 380: 230 pounds
Models 480 & 480XT: 295 pounds
408-213-2551
www.jumpsport.com
P/N: INS-P-11722-01A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 120 and is the answer not in the manual?

Questions and answers

Summary of Contents for JumpSport 120

  • Page 1 Alternate Assembly Instructions for Safety Enclosures Models 120, 280, 380, 480, and 480XT Assembly, Installation, Care, Maintenance, and Use Instructions WARNING Read these materials prior to assembling and using this Trampoline Enclosure attempt allow DO NOT allow more than one somersaults.
  • Page 2 JumpSport, Inc. is prohibited. The information in this document is subject to change without notice. JumpSport, Inc. shall not be liable for any damages resulting from technical errors or omissions, which may be present in this document, or from use of this document.
  • Page 3: Table Of Contents

    Contents Chapter 1 Introduction JumpSport ProFlex Basketball Set Game and Party Pak Chapter 2 Assembly and Installation Instructions Preparation Trampoline Placement Tools Parts List Assembly Type A Installation Type B Installation Final Steps Disassembly Please refer to the manual that came with your enclosure...
  • Page 4 (This page left intentionally blank.)
  • Page 5: Chapter 1 Introduction

    Misuse and abuse of this trampoline is dangerous, and can cause serious injuries. The purchaser/ user of this piece of equipment is assuming a degree of risk for which JumpSport cannot be responsible. Read this information thoroughly before allowing the trampoline to be used. Keep this manual available for your review, and for review by all potential users.
  • Page 6: Jumpsport Proflex Basketball Set

    Introduction JumpSport ProFlex Basketball Set Let’s face it, kids have to look up a lot: at parents, teachers, and • bigger brothers/sisters. With the Our most popular JumpSport ProFlex Basket- accessory! ball Set, look down for a change! • Easily installed to your...
  • Page 7: Chapter 2 Assembly And Installation Instructions

    This unit is not intended for commercial or public use and is therefore strictly prohibited. The maximum user weight is: 200 pounds (Model 280), 230 pounds (Models 120 & 380), or 295 pounds (Models 480 & 480XT), or the specified user weight rating of your trampoline, whichever is lower.
  • Page 8: Tools

    Parts List Your JumpSport Safety Enclosure is shipped with the parts shown below. Some parts will be located in a smaller inner box. If any parts are missing, immediately call JumpSport Customer Service at 408-213-2551. Note: Do NOT discard the foam tubing (Reference #3 and #4); it is needed to make the pole assemblies. It is not just packing material.
  • Page 9: Assembly

    Assembly and Installation Instructions The following pages contain diagrams, pictures, and written instructions for assembling your JumpSport Safety Enclosure. The “Ref. #” mentioned in many steps is referring to the “Reference #” column of the parts list on the previous pages.
  • Page 10 Assembly and Installation Instructions Pole 2 Pole 1 = u-shaped leg (6 total, with 12 vertical attachment points) = safety enclosure pole (8 total) Note: If your trampoline has 6 sets of u-shaped legs instead of 4, use the above diagram for pole placement.
  • Page 11 Using the hardware provided, connect a pole to the outside of each trampoline leg: • If you have a JumpSport Trampoline, bottom of pole must line up with red mark on vertical leg piece. This will ensure that pole is at proper height. (If red marks are missing, see below.)
  • Page 12 Assembly and Installation Instructions Wider top strap with loop Ref. #10 Bottom strap written and slaved over by Andy Graser for many long hours. special thanks to Jon Greiner and April Smith for their help and contributions. Knot Familiarize yourself with the net. The net has a wider strap at the top of the net. There are red marks on the top and bottom straps of net to help with installation.
  • Page 13 Assembly and Installation Instructions Pole 6 (Net shown hung on poles 1 - 4) Pole 2 Pole 4 Pole 1 (View from outside of net) Continue back to pole 1. Hang net around outside of pole 1, Pole 1 with top strap and 1 mesh of netting resting in groove on top of ball end cap.
  • Page 14 Assembly and Installation Instructions Type A Installation Button bungee If your trampoline frame pad has button bungees going through the large pad section of pad—as shown above—continue to the next step for Type A Installation. If your trampoline frame pad does NOT have button bungees going through middle of pad, skip to page 21 for Type B Installation.
  • Page 15: Type A Installation

    Assembly and Installation Instructions–Type Installation Type A Installation Note: Use page 8 to help with part names and numbers. All parts may not be used for this installation. Find pole that you tied off to top of net in Step 9. Lift frame pad between that pole and pole to left of it. Tuck pad skirt up underneath pad, so skirt is wedged between bottom of pad and rail of trampoline.
  • Page 16 Assembly and Installation Instructions–Type Installation Pole 3 Pole 2 Pole 2 Pole 1 The net between poles 1 and 3 should now look like the above pictures (but the pictures will only match if your net tied off to pole 1 instead of pole 8). For a top down view, see page 27. Bottom strap of net bungee...
  • Page 17 Assembly and Installation Instructions–Type Installation (Outer panels of net not shown for clarity.) Pole 2 Pole 1 Button bungee Square knot Find the 2 button bungees on top of frame pad between poles 1 and 2. Secure bottom strap of inner panel of net at each button bungee with a square knot, as shown.
  • Page 18 Assembly and Installation Instructions–Type Installation 10.5ft pole strap Ref. #12 bungee At pole that you tied off top of net to in Step 9, wrap a 10.5ft pole strap around the vertical leg piece as shown. Strap must wrap around pole and leg below rail, and behind 1ft bungee. Then pull non-looped end of pole strap all the way through looped end. I M P O R T AN T : F l i p warning placard up out of...
  • Page 19 Assembly and Installation Instructions–Type Installation (View from inside trampoline) (View from outside trampoline) Secure bottom strap of net to each button bungee sticking out of top of frame pad. Do not wrap pole strap around net mesh, only around bottom strap of net. Tie bungee to bottom strap of net as shown in Step 16. Warning placard Be sure the warning placard attached to the bottom strap of net (at the doorway) is clearly visible at all times.
  • Page 20 Assembly and Installation Instructions (Models 120, 380, 480, & 480XT only)– Type Installation (View from outside of net) 6ft bungee Ref. #13 (View from outside of net) Steps 21—26 are for Models 120, 380, 480, and 480XT only. If you have a 280, installation is now...
  • Page 21 Assembly and Installation Instructions (Models 120, 380, 480, & 480XT only)– Type Installation (Picture not to scale) (Side view) 10.5ft pole strap Tie end of 10.5ft pole strap off with a firm knot at bottom of pole, just below rail.
  • Page 22: Type B Installation

    Assembly and Installation Instructions–Type Installation Type B Installation Note: Use page 8 to help with part names and numbers. All parts may not be used for this installation. Lift frame pad between poles 1 and 2. Tuck pad skirt up underneath pad, so skirt is wedged between bottom of pad and rail of trampoline.
  • Page 23 Assembly and Installation Instructions–Type Installation Pole 3 Pole 2 Pole 2 Pole 1 The net between poles 1 and 3 should now look like the above pictures (but the pictures will only match if your net tied off to pole 1 instead of pole 8). For a top down view, see page 27. Bottom strap of net bungee...
  • Page 24 Assembly and Installation Instructions–Type Installation 10.5ft pole strap Ref. #12 bungee At pole that you tied off top of net to in Step 9, wrap a 10.5ft pole strap around the vertical leg piece as shown. Strap must wrap around pole and leg below rail, and behind 1ft bungee. Then pull non-looped end of pole strap all the way through looped end. I M P O R T AN T : F l i p warning placard up out of...
  • Page 25 Assembly and Installation Instructions–Type Installation Left half of bottom strap of Pole 3 Pole 2 Between poles 2 and 3, secure only the left half of bottom strap of net to trampoline rail. Pole strap will still wrap once between each spring all the way across the rail, but net itself will only be secured to rail on left half of net, as shown above.
  • Page 26 Assembly and Installation Instructions (Models 120, 380, 480, & 480XT only)– Type Installation (View from outside of net) 6ft bungee Ref. #13 (View from outside of net) Steps 20—25 are for Models 120, 380, 480, and 480XT only. If you have a 280, installation is now...
  • Page 27 Assembly and Installation Instructions (Models 120, 380, 480, & 480XT only)– Type Installation (Picture not to scale) (Side view) 10.5ft pole strap Tie end of 10.5ft pole strap off with a firm knot at bottom of pole, just below rail.
  • Page 28: Final Steps

    Assembly and Installation Instructions Final Steps Assembly is now complete! Make sure all parts are securely assembled. Before using your JumpSport Safety Enclosure, familiarize yourself and all users with the Care and Maintenance Instructions, Warning Information, and Use Instructions included in this manual. See Diagram 1, below, to see how to properly enter the safety enclosure.

This manual is also suitable for:

280480xt380480

Table of Contents