Table of Contents
Advertisement
Quick Links
1000W 5-Channel Marine Amplifier with 2-Way / 3-Way Crossover
Marine 5 Channel Amplifier with 2-Way / 3-Way Crossover
+12 VDC
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your vessel.
For maximum performance, we highly recommend that you have
your new amplifier installed by an authorized JL Audio dealer. Your
authorized dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly so as to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier's operation, please contact your
authorized JL Audio dealer for assistance. If you need further assistance,
please call the JL Audio Technical Support Department
owner's manual
Remote
Turn-On
Level
Mode
Mode
Rem. | O set | Signal
Input Voltage
Low | High
2 Ch. | 4 Ch. | 6 Ch.
(L)
CH. 1
CH. 3
SUB
CH. 2
CH. 4
SUB
(R)
Ground
Remote
Thank you for purchasing a JL Audio amplifier for
your marine sound system.
at (954) 443-1100 during business hours.
CH. 1 & 2
CH. 3 & 4
SUB CH.
Input
Input
Input
Sens.
Sens.
Sens.
All | Sub Ch.
Input Mode
HP Filter Mode
Filter Mode
LP Filter Mode
O | x1 | x10
O | BP | HP
O | 12dB | 24dB
Filter Freq. (Hz)
HP Filter Freq. (Hz)
LP Filter Freq. (Hz)
CH. 1
CH. 2
CH. 3
(L)
(R)
(L)
Mono Subwoofer Output
CH. 4
(R)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for JL Audio M1000/5v2
Summary of Contents for JL Audio M1000/5v2
- Page 1 For maximum performance, we highly recommend that you have your new amplifier installed by an authorized JL Audio dealer. Your authorized dealer has the training, expertise and installation equipment to ensure optimum performance from this product.
-
Page 2: Protect Your Hearing
This is an extremely dangerous high-power amplifiers are capable of producing The outer shell of your JL Audio amplifier is which does not interfere with your vessel’s safety practice which can result in severe damage to... -
Page 3: Product Description
Take care to route the wire in such a way that the amplifiers in the system). This large power only the M1000/5v2 is being run from that power it will not be damaged and will not interfere sensitivity controls to obtain the right wire should terminate into a fused distribution wire, we recommend a 80A fuse be used. -
Page 4: Turn-On Options
JL Audio ECS Speaker head of the screw and making sure that the wire & 4 Inputs. In this mode, the M1000/5v2 will derive Wire to RCA adaptor (XD-CLRAIC2-SW). is firmly gripped by the set screw. -
Page 5: Input Sensitivity Controls
(one high-pass filter for the full range of frequencies present at the inputs the entire M1000/5v2 from the front of the vessel you can then adjust any or all “Input Sens.” channels 1&2 and another high-pass / bandpass to feed this channel. -
Page 6: Speaker Outputs
There is a single multi-color LED on the top to accept 16 AWG - 8 AWG wire. To connect the When a pair of the M1000/5v2’s main channels designed to deliver power into subwoofer loads surface of the amplifier to indicate the amplifier’s... -
Page 7: System Configurations
Crossover Setup for Bi-Amplified System To operate a single M1000/5v2 in Tri-Amplified Filter Frequency you are adjusting with this control that it may be sent in to JL Audio for service. with one M1000/5v2: mode, set the “Input Mode” switch in “2 Ch.”... - Page 8 14.73”x 7.09” x 2.05” (374mm x 180mm x 52mm) 3Ω 16.2 V not recommended 38.7 V 2Ω 14.1 V not recommended 34.6 V Due to ongoing product development, all specifications are subject to change without notice. 14 | JL Audio - M1000/5v2 Owner’s Manual...
- Page 9 Please refer to Appendix A (page 14) to set the input sensitivity for Check your voltage source and grounding point. The power supply maximum, low-distortion output. of the M1000/5v2 will operate with charging system voltages “my amplifier doesn’t turn on.” down to 10V. Shutdown problems at higher volume levels Check the fuse, not just visually, but with a continuity meter.
-
Page 10: Installation Notes
Filter Freq. (Hz) HP Filter Freq. (Hz) LP Filter Freq. (Hz) CH. 1 CH. 3 Mono Subwoofer Output CH. 2 CH. 4 CH. 1 CH. 2 CH. 3 CH. 4 +12 VDC Ground Remote 18 | JL Audio - M1000/5v2 Owner’s Manual... - Page 11 All warranty returns should be sent to JL AUDIO ’s Amplifier Service Facility freight-prepaid through an authorized JL AUDIO dealer and must be accompanied by proof of purchase (a copy of the original sales receipt). Direct returns from consumers or non-authorized dealers will be refused unless specifically authorized by JL AUDIO with a valid return authorization number.
Need help?
Do you have a question about the M1000/5v2 and is the answer not in the manual?
Questions and answers