Husqvarna 335RJ Operator's Manual

Husqvarna grass trimmer operator's manual


Oper ator's manual (EPA)
333RJ 335RJ
Please r ead the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.


Table of Contents

Summary of Contents for Husqvarna 335RJ

  • Page 1 Oper ator’s manual (EPA) 333RJ 335RJ X-series Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
  • Page 2: Key To Symbols

    Arrows which show limits for handle positioning. Always wear approved protective gloves. Wear sturdy, non-slip boots. Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. 2 – English KEY TO SYMBOLS Starting instructions Other symbols/decals on the machine refer to special certification requirements for certain markets.
  • Page 3: Table Of Contents

    WARNING! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual.
  • Page 4: Introduction

    Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.
  • Page 5: What Is What

    What is what on the clearing saw? 1 Trimmer head 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Handle adjustment 7 Loop handle 8 Suspension ring 9 Stop switch 10 Throttle lockout...
  • Page 6: General Safety Precautions

    English Personal protective equipment IMPORTANT! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual.
  • Page 7: Machine's Safety Equipment

    GENERAL SAFETY PRECAUTIONS CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level. FIRST AID KIT Always have a first aid kit nearby.
  • Page 8 GENERAL SAFETY PRECAUTIONS Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment. Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked.
  • Page 9: Cutting Equipment

    WARNING! Using an incorrect cutting attachment or an incorrectly sharpened blade increases the risk of blade thrust. Cutting equipment Grass blades and grass cutters are intended for cutting coarse grass. A trimmer head is intended for trimming grass. – 9 English...
  • Page 10: Sharpening Grass Cutters And Grass Blades

    • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.
  • Page 11: Assembly

    • Attach the J-handle to the loop handle using the three screws, as shown. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. WARNING! Only grass blades/grass cutters or trimmer heads/plastic blades may be used when the J-handle is fitted.
  • Page 12: Fitting A Blade Guard, Grass Blade And Grass Cutter

    CAUTION! Ensure that the guard extension is fitted. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft.
  • Page 13: Fuel Handling

    When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke engine oil, which is specially formulated for our air- cooled two stroke-engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).
  • Page 14: Fueling

    Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. •...
  • Page 15: Starting And Stopping

    • Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard.
  • Page 16 STARTING AND STOPPING Repeat pulling the cord until the engine starts. When the engine starts. return choke control to run position and apply full throttle; the throttle will automatically disengage from the start setting. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended.
  • Page 17: Working Techniques

    General working instructions IMPORTANT! This section describes the basic safety precautions for working with clearing saws and trimmers. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability.
  • Page 18: Basic Working Techniques

    Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.
  • Page 19 Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.
  • Page 20: Maintenance

    Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions...
  • Page 21: Muffler

    H. You should therefore fit the trimmer head T35 (2.7 mm cord) before adjusting the high speed jet. The cord length should be standard, i.e. to the knife on the trimmer guard. Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down.
  • Page 22: Cooling System

    However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out.
  • Page 23: Spark Plug

    Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor. Note: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically...
  • Page 24: Maintenance Schedule

    Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. Check that the locking nut of the cutting equipment is tighten correctly.
  • Page 25: Technical Data Technical Data

    NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. Approved accessories Centre hole in blades/cutters, Ø 25,4 mm Output shaft thread M12 Grass blade/grass cutter Plastic blades Trimmer head Support cup TECHNICAL DATA 333RJ 2,11/34,6 1,50/38,0 1,20/30,5...
  • Page 26: Federal And California Emissions Control Warranty Statement

    MANUFACTURER′ ′ ′ ′ S WARRANTY COVERAGE The emissions control system is warranted for two years. If any emissions-related part on your equipment is defective, the part will be repaired or replaced by Husqvarna Forest & Garden. OWNER′ ′ ′ ′ S WARRANTY RESPONSIBILITIES •...
  • Page 27 EPA may not be used. The use of any non-exempted add-on or modified parts will be grounds for disallowing a warranty claim. Husqvarna Forest & Garden will not be liable to warrant failures of warranted parts caused by the use of a non- exempted add-on or modified part.
  • Page 29 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 30 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 31 15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...
  • Page 32 15 cm 6" 10 m 10 cm 4" 4,3 m "Clic"...
  • Page 34 ´®z+RCG¶5K¨ ´®z+RCG¶5K¨...
  • Page 36 1150353-95 ´®z+RCG¶5K¨ ´®z+RCG¶5K¨ 2006-12-15...

This manual is also suitable for:

333rj335rjx series

Table of Contents