Download Table of Contents Print this page

Husqvarna 333J SERIES Operator's Manual


Quick Links

Operator's manual
333RJ 335RJ
Please read the operator's manual carefully and make sure you understand the instructions
before using the machine.
E E E E n n n n g g g g l l l l i i i i s s s s h h h h


Table of Contents

Summary of Contents for Husqvarna 333J SERIES

  • Page 1 Operator′s manual 333RJ 335RJ X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
  • Page 2: Key To Symbols

    KEY T O SYMBOLS Symbols W ARNING! Clearing saws, Only use non-metallic, flexible cutting brushcutters and trimmers can be attachments, i.e. trimmer heads with dangerous! Careless or incorrect use trimmer cord. can result in serious or fatal injury to the operator or others. Please read the operator’s manual Noise emission to the environment carefully and make sure you...
  • Page 3: Table Of Contents

    CONTENTS Contents Note the f ollowing before starting: KEY TO SYMBOLS Please read the oper ator’s manual carefully. Symbols ..............2 W ARNING! Long-term exposure to noise CONTENTS can result in permanent hearing Contents ..............3 impairment. So always use approved Note the following before starting: ......
  • Page 4: Intr Oduction

    Dear Customer , Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets.
  • Page 5: Wha T Is What

    WHA T IS WHA T? What is what on the c learing saw? Trimmer head 17 Choke control Grease filler cap, bevel gear 18 Air purge Bevel gear 19 Locking nut Cutting attachment guard 20 Support flange Shaft 21 Support cup Handle adjustment 22 Blade Loop handle...
  • Page 6: General Safety Preca Utions

    GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment IMPORTANT! IMPOR TANT! A clearing saw, brushcutter or trimmer can be dangerous if The machine is only designed for trimming grass. used incorrectly or carelessly, and can cause serious or The only accessories you can operate with this engine unit fatal injury to the operator or others.
  • Page 7: Machine's Safety Equipment

    GENERAL SAFETY PRECAUTIONS CLOTHING Make sure the throttle control is locked at the idle setting when the throttle lockout is released. Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants.
  • Page 8 GENERAL SAFETY PRECA UTIONS Cutting attac hment guard Check that the vibration damping element is undamaged and securely attached. WARNING! Overexposure to vibration can lead to circulatory damage or nerve This guard is intended to prevent loose objects from being damage in people who have impaired thrown towards the operator.
  • Page 9: Cutting Equipment

    GENERAL SAFETY PRECAUTIONS Never use a machine that has a faulty muffler. Locking nut A locking nut is used to secure some types of cutting attachment. Regularly check that the muffler is securely attached to the machine. When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment.
  • Page 10 GENERAL SAFETY PRECAUTIONS Sharpening grass cutters and grass blades WARNING! Always stop the engine before doing any work on the cutting attachment. This continues to rotate even after the throttle has been released. Ensure that the • See the cutting attachment packaging for correct cutting attachment has stopped completely sharpening instructions.
  • Page 11: Assembly

    ASSEMBLY Fitting the J-handle Assembling the cutting equipment • Clip the loop handle onto the shaft. Note that the loop WARNING! handle must be fitted between the arrows on the shaft. When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment.
  • Page 12: Fitting A Blade Guard, Grass Blade And Grass Cutter

    ASSEMBLY Fitting a blade guard, grass blade Fitting other guards and cutting and grass cutter attachments • Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. CAUTION! Ensure that the guard extension is fitted. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M).
  • Page 13: Fuel Handling

    Two-stroke oil storage. • For best results and performance use HUSQVARNA • In order to prevent unintentional starting of the engine, two-stroke engine oil, which is specially formulated for the spark plug cap must always be removed during long- our air-cooled two-stroke engines.
  • Page 14: Fuelling

    FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the WARNING! Taking the following fuel mixture.
  • Page 15: Starting And Stopping

    STARTING AND STOPPING Check before starting trimmer guard if they have been exposed to impact or are cracked. • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with...
  • Page 16 STARTING AND STOPPING Stopping Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Stop the engine by switching off the ignition. WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately.
  • Page 17: Working Techniques

    WORKING TECHNIQUES General working instructions Always hold the machine with both hands. Hold the machine on the right side of your body. IMPORTANT! This section describes the basic safety precautions for working with clearing saws and trimmers. If you encounter a situation where you are uncertain how to proceed you should ask an expert.
  • Page 18 WORKING TECHNIQUES Basic working techniques • Let the support cup rest lightly against the ground. It is used to protect the blade from hitting the ground. Always slow the engine to idle speed after each working • Reduce the risk of material wrapping around the blade operation.
  • Page 19 WORKING TECHNIQUES Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.
  • Page 20: Maintenance

    Carburettor be finely adjusted. Fine adjustment should be carried out by a skilled technician. Your Husqvarna product has been designed and CAUTION! If the cutting attachment rotates when the manufactured to specifications that reduce harmful engine is idling the idle adjustment screw T should be turned emissions.
  • Page 21: Muffler

    MAINTENANCE Fine adjustment of the idle speed T to run unevenly. Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly. Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust.
  • Page 22: Cooling System

    filled three-quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not normally need to be CAUTION! Never use a machine with a defective muffler.
  • Page 23: Spark Plug

    MAINTENANCE Oiling the air filter Always use special filter oil. Filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil.
  • Page 24: Maintenance Schedule

    MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorised service workshop.
  • Page 25: Technical D Atat Echnical Data

    TECHNICAL DATA Technical data Technical data 333RJ 335RJx Engine Cylinder displacement, cm 34,6 34,6 Cylinder bore, mm 38,0 38,0 Stroke, mm 30,5 30,5 Idle speed, rpm 2900 2900 Recommended max. fast idle speed, rpm 11500 11500 Speed of output shaft, rpm 8220 8220 Max.
  • Page 26: Ec-Declaration Of Conformity

    (Applies to Europe only) We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the clearing saws Husqvarna 333RJ and 335RJX with serial numbers dating from 2006 onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:...
  • Page 27 TECHNICAL DATA English – 27...
  • Page 28 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 29 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 30 T35, T35x 8,5 m 10 cm 4" 4,3 m "Clic" 15 cm 6"...
  • Page 31 T45, T45x 10 m 10 cm 4" 4,3 m 15 cm "Clic" 6"...
  • Page 36 1150887-26 ´®z+Rxh¶6®¨ ´®z+Rxh¶6®¨ 2008-03-19...

This manual is also suitable for:

335rjx series

Table of Contents