1. Manuals
  2. Brands
  3. Chiayo Manuals
  4. Stereo System
  5. SMART300
  6. Operation manual

Chiayo SMART300 Operation Manual

Portable sound system
Hide thumbs Also See for SMART300:

Advertisement

Table of Contents

See also: Operating Manual
CHIAYO ELECTRONICS CO., LTD.
http://www.chiayo.com.tw
OFFICE: 30, LANE 27, SEC.4. JEN-AL ROAD, TAIPEI, TAIWAN / TEL: 886-2-2741-5741
FACTORY: 88, CHUNG HSIAO STREET 2, CHIAYI, TAIWAN. / TEL: 886-5-271-1000
Printed in Taiwan, April 2008
E-mail: sales@chiayo.com.tw
FAX: 886-2-2752-5242
FAX: 886-5-276-7611
12I1153
GREEN PRODUCT
GREEN PRODUCT
It has been RoHS Compliant
It has been RoHS Compliant
Portable Sound System
OPERATION MANUAL
OPERATION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SMART300 and is the answer not in the manual?

Questions and answers

Related Manuals for Chiayo SMART300

Summary of Contents for Chiayo SMART300

  • Page 1 OPERATION MANUAL GREEN PRODUCT GREEN PRODUCT It has been RoHS Compliant It has been RoHS Compliant CHIAYO ELECTRONICS CO., LTD. http://www.chiayo.com.tw E-mail: sales@chiayo.com.tw OFFICE: 30, LANE 27, SEC.4. JEN-AL ROAD, TAIPEI, TAIWAN / TEL: 886-2-2741-5741 FAX: 886-2-2752-5242 FACTORY: 88, CHUNG HSIAO STREET 2, CHIAYI, TAIWAN. / TEL: 886-5-271-1000...

  • Page 2: Optional Accessories

    SMART 300 Operation Manual Maintenance-free Lead Acid battery Congratulation and thank you for the purchase of this all-in-one ultra compact Guidelines for maintenance-free Batteries: portable sound system. 1. Battery should operate at temperatures between 15°C ~ 50°C. To ensure a longer life span, it To ensure a trouble-free operation, please read this manual thoroughly to fully should be kept between 5°C ~ 35°C.
  • Page 3 SMART 300 SMART 300 Passive Speaker Caution and tips on how to obtain the best results. ( Amplifier version ) 1. Before inserting the batteries, please make sure that they are inserted according to the correct polarity. 2. The audio cable of VHF transmitters also serves as antenna. The length of the cable is cut according to the specific frequency range.
  • Page 4 Operating procedures VHF Beltpack Transmitter M-1002 Par ts & Fu nc tion s After unpacking the unit for the first time, please charge the unit for about 4~5 hours before any operation. This is absolutely necessary as the built-in rechargeable battery might have been discharged naturally due to long shipment and storage time, even Battery status Power Switch...
  • Page 5 Beltpack Transmitter SM-816(UHF) / SM-216(VHF) Operating the dynamic wired microphone There is a MIC IN jack with dedicated volume control for this portable sound unit. To use a cable microphone ( dynamic only ), just plug the end with a phone jack plug into MIC IN .
  • Page 6 UHF Handheld Transmitter SQ-5016 Installation of cable restraint To prevent contact noise caused by constant tension Parts and functions applied to the connector,,a cable restraint is designed such that tension is totally reduced when it is properly used. When the audio cable go through the cable restraint, it could prevent sweat from going directly into the electronic board via the connector.
  • Page 7 Beltpack Transmitter SM-916(UHF) / SM-316(VHF) Battery installation Antenna(SM-916) SM-916/SM-316 use a 9V battery. To insert the battery, first open the battery compartment cover by pressing the Battery status cover downward till the door flips open Indic ator by itself (see below picture). When Cable Power swit ch restrain t...

  • Page 8: Handheld Transmitter

    Handheld Transmitter SQ-916(UHF) / SQ-316(VHF) Parts & functions 1. Capsule with metal grille 2. Battery indicator 3. Sensitivity switch 4. Power on/off switch 5. Battery cover 7. Color cap Battery installation SQ-916/SQ-316 use a 9V battery for power. To change or replace the battery, please remove the color cap first, then press the bottom of battery compartment to release the cover as shown below.

  • Page 9: Battery Installation

    UHF Beltpack Transmitter SM-5016 Changing of capsule This microphone has a modular design. To change or replace a capsule, Open the grill to pull out and plug in the capsule as shown in the following figure. Parts & Functions Antenna Battery weak / audio mute indicator Audio mute switch Mini-XLR connector...

  • Page 10: Parts And Functions

    Handheld Transmitter SQ-816(UHF) / SQ-216(VHF) VHF Handheld Transmitter Q-1002 Parts and Functions Parts & functions Battery compartment Battery status cover LED indicator Color cap Metal Grille ( Capsule module inside ) Power Switch Battery Installation 1. Capsule with metal grille Q-1002 uses 1 piece of 9V battery.

Table of Contents