Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Fujitsu B27T-7
Summary of Contents for Fujitsu B27T-7
- Page 1 Display Operating Manual B27T-7 LED...
- Page 2 You can find driver updates at: "http://support.ts.fujitsu.com/download" Should you have any technical questions, please contact: • our Hotline/Service Desk (see the Service Desk list or visit: "http://support.ts.fujitsu.com/contact/servicedesk") • Your sales partner • Your sales office We hope you enjoy working with your new Fujitsu system!
- Page 4 Published by / Contact address in the EU Fujitsu Technology Solutions GmbH Mies-van-der-Rohe-Straße 8 80807 Munich, Germany "http://www.fujitsu.com/fts/" Copyright © Fujitsu Technology Solutions GmbH 2013. All rights reserved. Publication Date 06/2013 Order No.: A26361-K1478-Z320-1-7619, edition 1...
-
Page 5: Table Of Contents
B27T-7 LED Operating Manual Your LCD screen... Important notes Getting started Operation Notes on ergonomic colour adjustment Troubleshooting Explanatory information about standard ISO 9241-307 Technical specification... - Page 6 Trademarks Fujitsu and the Fujitsu logo are registered trade marks of Fujitsu Limited or its subsidiaries in the United States and other countries. Microsoft and Windows are trademarks or registered trademarks of the Microsoft Corporation in the United States and/or other countries.
- Page 7 DisplayPort socket ..............36 Fujitsu...
- Page 8 Contents Fujitsu...
-
Page 9: Your Lcd Screen
You don’t need to be an "expert" to perform the operations described here. Nonetheless, it is important to always observe the safety notes given in the operating instructions for the computer and in this manual. In the event of any problems, please contact your sales office or our Service Desk. Fujitsu... -
Page 10: Further Information
"Safety information" • cross-references to an external source, e.g. a web address: For more information, go to "http://www.fujitsu.com/fts/" • Names of CDs, DVDs and titles or designations of other materials, e.g.: "CD/DVD Drivers & Utilities" or "Safety" Manual indicates a button or a contact sensor on the monitor, e.g:... -
Page 11: Important Notes
Use a screen saver with moving images and activate the power management for • your monitor to prevent still images from "burning in". • If you operate the device with the swivel arm or a similar accessory, it must not be turned by 180°. Fujitsu... -
Page 12: Power Cable
If the device is brought from a cold environment into the room where it will be used, condensation may occur. Before operating the device, wait until it is absolutely dry and has reached approximately the same temperature as the installation site. Fujitsu... -
Page 13: Cleaning The Device
CE marking The shipped version of this device complies with the requirements of EU directives 2004/108/EC "Electromagnetic compatibility", 2006/95/EC "Low voltage directive", 2009/125/EC "Ecodesign directive" and 2011/65/EC "RoHS directive". Fujitsu... -
Page 14: Disposal And Recycling
The device must be disposed of in accordance with the local regulations for disposal of special waste. If you have any questions on disposal, please contact your local sales office or our Service Desk, or contact one of the following directly: Germany Belgium Switzerland Fujitsu Technology Solutions RECUPEL SWICO GmbH Boulevard Reyers, 80 Schweizerischer... -
Page 15: Getting Started
► Should you discover that the delivery does not correspond to the delivery note, notify your local sales outlet immediately. Do not discard the original packing material of the devices. You may need the packaging in the future if you need to transport your device. Fujitsu... -
Page 16: Setting Up The Device
To ensure sufficient ventilation, the air inlet and outlet openings of the device must be kept clear. Setting up an ergonomic video workstation ► Do not position the video workstation opposite a window (1). ► Position the monitor outside the reach of a light source (1). Fujitsu... - Page 17 Depending on the situation, it may be advisable to use a swivel arm or a similar accessory (VESA FDMI), which are available from specialist dealers. For this purpose the monitor base must be removed beforehand as described in chapter "Removing monitor base", Page Fujitsu...
-
Page 18: Adjusting Height
The inclination of the monitor can be adjusted by -3° (forwards) and +35° (backwards) from its vertical position. ► Hold the monitor with both hands on the left and right sides of the casing and move it to the desired angle. Fujitsu... -
Page 19: Removing Monitor Base
VESA FDMI using a hole spacing of 100 mm (VESA MIS‑D, 100, C). For instructions on how to mount the swivel arm or a similar accessory, please see the documentation for the swivel arm or similar accessory. Fujitsu... -
Page 20: Connecting The Device
2 = Power connector 7 = AUDIO-OUT socket 3 = AUDIO-IN socket 8 = USB IN (Upstream) 4 = DisplayPort socket 9 = USB OUT (Downstream) 5 = DVI-D socket (DVI) ► Select the appropriate data cable for your computer. Fujitsu... -
Page 21: Connecting Cables To The Computer
► Plug the power connector of the computer into a properly grounded mains outlet. If your computer has two monitor ports ("onboard" screen controller and separate graphics card), the monitor port for the separate graphics card is active as standard. Fujitsu... -
Page 22: Operation
Monitor and computer are switched on (ECO mode). orange Monitor is not receiving a video signal or is in power saving mode. does not light up Monitor is switched off. ► Switch the device on with the contact sensor for the ON/OFF switch (1). Fujitsu... -
Page 23: Notes On Power Management
ECO mode is the preset factory default. Once an input is made at the computer the screen contents are restored. For detailed information on how energy-saving mode operates, please refer to the operating manual or technical manual of the computer. Fujitsu... -
Page 24: Changing The Monitor Settings
(On-Screen Display) is active, the current meaning of the sensors is shown directly over the contact sensors on the edge of the screen. The display over the contact sensors varies depending on the submenu chosen. 1 = Contact sensors of the control panel 2 = Current sensor function Fujitsu... -
Page 25: Changing The Monitor Settings With The Contact Sensors Of The Control Panel
The message ECO Mode on or ECO Mode off is displayed. If the ECO operating mode is activated, the following OSD settings are changed: 6500 K Colour reduced Brightness After the ECO operating mode is switched off, the brightness previously set by the user is restored. Fujitsu... -
Page 26: Locking The Osd Menu
The message OSD locked and a progress bar appear. ► To activate the lock function, touch both sensors until the progress bar is fully loaded. The OSD menu is locked. Please proceed in the same manner to release the locked OSD menu again. Fujitsu... -
Page 27: Changing The Monitor Settings Using The Osd Menu
INPUT ► Touch the MENU sensor to select the highlighted submenu. The adjustment window will be displayed (e.g. Image adjust ). Further settings can be made here. ► To return to the main menu, touch the sensor. AUTO Fujitsu... -
Page 28: Changing Settings
All possible adjustments of the main menu are described in the following. OSD menu functions The OSD menu for analogue monitor operation is described below. During digital operation some functions are not available, as they are not required due to the digital transmission technology used. Fujitsu... -
Page 29: Adjusting The Brightness And Contrast
With this function you move the picture to the left or to the right. Adjust the vertical position V-Position With this function you move the picture up or down. Adjust the picture size Expansion Full screen = selection of full screen mode Keep aspect = maximum picture size without distortion Fujitsu... -
Page 30: Adjusting The Volume
With this function you switch the OSD menu from portrait mode to landscape OSD Rotation mode and vice versa. On = The OSD menu is displayed in portrait mode. Off = The OSD menu is displayed in landscape mode. Fujitsu... -
Page 31: Displaying Information
With this function all settings are reset to the factory settings without prompting for confirmation. Touch the sensor to activate the function. The Auto Processing message is displayed. Displaying information Call the Information setting window This function displays the model designation, serial number, resolution, H/V frequency and ECO mode. Fujitsu... -
Page 32: Notes On Ergonomic Colour Adjustment
+ Colour combination very suitable - Colour combination not suitable because colour hues are too close together, thin characters are not identifiable or rigorous focusing is demanded of the human eye. Fujitsu... -
Page 33: Troubleshooting
► Touch the sensor to conduct AUTO auto-adjustment of the screen. Picture is wrongly adjusted ► Run the Factory Recall function in the OSD menu. The Auto Processing message appears. Fujitsu... - Page 34 The screen becomes darker The background lighting has a limited lifetime. If your monitor display should become too dark, the background lighting will have to be replaced. ► Contact our Service Desk. Fujitsu...
-
Page 35: Explanatory Information About Standard Iso 9241-307
The maximum permitted number of faulty pixels is stipulated in the international standard ISO 9241-307. In accordance with standard ISO 9241-3, LCD monitors by Fujitsu comply with Class II for low resolutions and Class I for resolutions of 1680 x 1050 (1764000 pixel) and higher. -
Page 36: Technical Specification
Technical specification Technical specification Condensation is not permitted, neither in the rated range of operation nor in the limit range of operation. Product name B27T-7 LED Model name B27T-7 Dimensions and weight Visible diagonals 68.5 cm Dot pitch 0.3114 mm... -
Page 37: Vesa-Ddc-Compatible Vga Interface
60 Hz 1440 x 900 60,0 kHz 75 Hz 1024 x 768 64,0 kHz 60 Hz 1280 x 1024 65,0 kHz 60 Hz 1680 x 1050 67,6 kHz 60 Hz 1920 x 1080 80,0 kHz 75 Hz 1280 x 1024 Fujitsu... -
Page 38: Additional Operating Modes
1600 x 900 SUB D port Meaning Video input red Video input green Video input blue Ground Ground Video ground red Video ground green Video ground blue +5 V (DDC) Sync. ground Ground DDC Data H. sync V. sync DDC Clock Fujitsu... -
Page 39: Dvi-D Port
Analog Vertical Sync TMDS Data1– TMDS Data1+ TMDS Data 1/3 Shield not connected not connected +5V Power Earth Hot Plug Detect TMDS Data0– TMDS Data0+ TMDS Data 0/5 Shield not connected not connected TMDS Clock Shield TMDS Clock+ TMDS Clock– Fujitsu... -
Page 40: Displayport Socket
Lane 1 (negative) Earth Lane 1 (positive) Lane 0 (negative) Earth Lane 0 (positive) Connected to earth Connected to earth Auxiliary channel (positive) Earth Auxiliary channel (negative) Hot Plug Detect Return for Power Power for connector (3.3 V 500 mA) Fujitsu...