Download
Share
Print this page
Honeywell VisionPRO 8000 Installer Setup And System Test Pocket Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Thermostat
  5. VisionPRO 8000
  6. Installer setup and system test pocket manual

Honeywell VisionPRO 8000 Installer Setup And System Test Pocket Manual

Hide thumbs Also See for VisionPRO 8000:

Advertisement

Quick Links

Download this manual See also: Owner's Manual, Product Data
®
VisionPRO
8000
Thermostats
INSTALLER SETUP AND
SYSTEM TEST POCKET
GUIDE
62-0266

Advertisement

loading
Need help?

Need help?

Do you have a question about the VisionPRO 8000 and is the answer not in the manual?

Questions and answers

steve lahue
February 6, 2025

I have this vision pro 8000, how do I set the 2nd stage of my heat pump to come on at a set outdoor temp?

0
1 comments:
Mr. Anderson
February 10, 2025

The second stage of the Honeywell VisionPRO 8000 heat pump is controlled by factors such as load conditions, environmental conditions, P+I control, and home insulation. However, you can fine-tune its operation using an outdoor temperature sensor and balance point settings.

To set the second stage to activate at a specific outdoor temperature:
1. Install the C7089U Outdoor Temperature Sensor.
2. Ensure the thermostat’s Installer Setup Number 0340 is set to 1 or 2 to enable outdoor temperature display.
3. Use the thermostat setup options to adjust the balance point, which determines when the second stage or auxiliary heat activates based on outdoor temperature.

This setup allows the system to optimize efficiency and comfort by adjusting heating stages according to outdoor conditions.

This answer is automatically generated

0

Subscribe to Our Youtube Channel

Related Manuals for Honeywell VisionPRO 8000

Summary of Contents for Honeywell VisionPRO 8000

  • Page 1 ® VisionPRO 8000 Thermostats INSTALLER SETUP AND SYSTEM TEST POCKET GUIDE 62-0266...

  • Page 2: Installer Setup

    INSTALLER SETUP 1. Press SYSTEM. Inside AUTO SYSTEM HEAT SCHED HOLD M24079 2. Press and hold these two blank buttons until the display changes. SYSTEM HEAT CANCEL DONE M24080 62-0266...

  • Page 3: Installer Setup Functions

    3. Use arrows to change settings as required. SETTING FUNCTION DONE PRESS PRESS SELECT FUNCTION CHANGE SETTING M24082A 4. Press DONE to exit and save settings. INSTALLER SETUP FUNCTIONS Available option and default settings vary by thermostat. Table 1. Installer Setup . Installer Installer Setup...
  • Page 4 Table 1. Installer Setup (Continued). Installer Installer Setup Setup Default Number Name Setting All Settings Notes 0170 System 1—1H/1C Conv Selection 2—1H/1C HP 3—1H w/o fan 4—1H with fan 6—1C 7—2H/1C HP 8—2H/2C Conv 9—2H/1C Conv 10—1H/2C Conv 11—2H/2C HP 12—3H/2C HP 0175 TOD/...
  • Page 5 Table 1. Installer Setup (Continued). Installer Installer Setup Setup Default Number Name Setting All Settings Notes 0230 CPH for Only shown if two second stages of cool stage selected. compressor 0240 CPH for first 1-12 Only shown if stage system is conventional conventional with heat...
  • Page 6 Table 1. Installer Setup (Continued). Installer Installer Setup Setup Default Number Name Setting All Settings Notes 0320 Temperature 0—° F Indication 1—° C Scale 0330 Daylight 0—Disabled Saving 1—Enabled (US 1987) 2—Enable (US 2007) 3—Enabled (Europe) 0340 Remote 0—None Averaging would Temperature 1—Outdoor for Display not include on-...
  • Page 7 Table 1. Installer Setup (Continued). Installer Installer Setup Setup Default Number Name Setting All Settings Notes 0535 Temporary 0—no duration 0 means no limit Occupied 1—one hour Duration 2—two hours Limit 3—three hours 4—four hours 0540 Number of 2—2 Periods Does not appear if Periods 4—4 Periods...
  • Page 8 Table 1. Installer Setup (Continued). Installer Installer Setup Setup Default Number Name Setting All Settings Notes 0670 Keypad 0—Unlocked Unlocked: All Lockout 1—Partial Lockout 1 functions 2—Partial Lockout 2 accessible. 3—Fully Locked Partial 1: Locks all but Holiday, Override, and Up/ Down.
  • Page 9 Table 1. Installer Setup (Continued). Installer Installer Setup Setup Default Number Name Setting All Settings Notes 0690 Temperature 1—Less Aggressive Only shown if Control Cool 2—Standard system has cool 3—More Aggressive stages. Only integral gains affected. Affects control operation in all control regimes (not just recovery or setpoint...

  • Page 10: Installer System Test

    INSTALLER SYSTEM TEST The installer Test is part of the Installer Setup Menu. 1. Enter the installer System Test by entering the Installer Setup and pressing repeatedly until “Test” appears. DONE M24083 2. Use arrow to change test and system status as required.

  • Page 11: System Tests

    SYSTEM TESTS Test the system’s heating cooling, fan and emergency heat. Available tests vary by thermostat and system type. Table 2. Installer System Tests. System Test Default System Status Number Test Type Number Setting and Description Test 1 Installer Test 0—Off Cool 1—Cool Stage 1...
  • Page 12 Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 yourhome.honeywell.com ® U.S. Registered Trademark © 2007 Honeywell International Inc. 62-0266 J.I. 09-08...