Page 1
Instruction manual Electric Storage Water Heater / Models SWH FS2 30 H SWH FS1 30 V SWH FS2 50 H SWH FS1 50 V SWH FS2 80 H SWH FS1 80 V SWH FS2 100 H SWH FS1 100 V SWH FS6 30 H SWH FS5 30 V SWH FS6 50 H...
TIMBERK electric storage water heaters will provide a lot of hot water and it is properly earthed. If there is no earth circuit in your electrical main then will automatically maintain the specified temperature.
Page 5
IMPORTANT! Technical characteristics of the water heater you purchased as of the date of manufacture correspond to data, specified in the table. Technical characteristics and scope of delivery can be revised without any prior notice. www.timberk.com storage water heater...
14 urethane foam heat insulation layer 15 external decorative case 16 power cable with GFCI* 17 remote control (FS6 series) * Depending on the product batch, GFCI can be located not within the power cable electric plug. Fig. 3 www.timberk.com Storage water heater...
Page 8
14 hot water outlet nozzle 15 the upper part of the hot water intake tube 16 remote control (FS5) * Depending on the product batch, GFCI can be located not within the power cable electric plug. Fig. 4 www.timberk.com storage water heater...
Fig.3-4 (FS1/FS5/FE1 line vertically, FS2/FS6/FE2 horizontally). Mounting of the appliance in any other position or vertical or horizontal tilting will inevitably result in failure of the water heater, emergency situation and is considered a non-guarantee case by the manufacturer. www.timberk.com Storage water heater...
* not included in the delivery set ** Depending on the product batch, GFCI can be located not within the power cable ** Depending on the product batch, GFCI can be located not within the power cable electric plug. electric plug. www.timberk.com storage water heater...
If pressure in the main exceeds 0.7 MPa, then it is necessary to mount a pressure reducer before the water heater so that pressure doesn't exceed 0.7 MPa. Fig. 8 www.timberk.com storage water heater...
The appliance must be used with a properly grounded power outlet. If the outlet, you are intending to use, is not properly grounded or grounded by a time-delay fuse or a circuit breaker, contact a qualified electrician to install a proper outlet. www.timberk.com storage water heater...
- to reduce the risk of an electric shock, do not disassemble, remove or 2. Switcher will be used in order to choose power modes. fill liquid in this appliance. * Color and design of device panels can be revised without any special notice. www.timberk.com storage water heater...
(1200 W), high heating power When pressed, the temperature controller handle also performs the express heat (2000 W). ON/OFF button function. When pressed, the temperature controller handle also performs the ON/OFF button function. 10. Water heating indicator www.timberk.com storage water heater...
It is used to activate timer and night heating. 3. ON/OFF button It is used to switch on/off the appliance. 4. « » button It is used to increase the selected value. 5. MODE button It is used to set time and timer. www.timberk.com storage water heater...
NOTE: When setting temperature, having reached the optimal heating position (+58° (+/- 2° ), you will hear a sound signal (for some models). www.timberk.com storage water heater...
NOTE: When setting temperature, having reached the optimal heating position (+58° (+/- 2° ), you will hear a sound signal (for some models). www.timberk.com storage water heater...
When water temperature in the water heater drops to a certain level, the heating is automatically switched off, at that indicator light on the control panel lights up. www.timberk.com storage water heater...
6.1. Press mode button twice to activate night heating, at that indicator on the display will light up. 6.2. Press mode button twice again to deactivate night heating, at that Fig. 17 indicator on the display will light down. www.timberk.com storage water heater...
Page 20
(below 0°C), it is necessary to drain water from the energize the water heater, cut off water supply and contact your heater . local Timberk Authorized Service Center for a consult or repair of the appliance. 3. To ensure long reliable water heater operation, it is recommended to regularly clean the internal tank and remove deposits on the electric 6.
Seal at the point of the heating element appliances case connection is broken. 1. Temperature adjustment device is 1. Contact a repairer, TIMBERK service Heating indicator light broken. center. lights up but water is not 2. Insufficient time for heating.
The manufacturer shall not be liable for changes in the appliance's wiring diagram that may be implemented without notice to the consumers. Fig.18 For models FS5/FS6/FE1/FE2 Thermal switch Actuating unit t° sensor Heating element 1 Heating element 2 Control unit (programmer, control t°, etc) Fig.19 www.timberk.com Storage water heater...
Page 31
FS2/FS6/FE2 .8). : 230V/10A, FS2/FS6/FE2 1,8 . FS1/FS5/FE1 1. Нагреватель подключается к водопроводной сети с давлением минимум 0,1 МПа, максимум 0,7 МПа www.timberk.com...
Need help?
Do you have a question about the SWHFS130V and is the answer not in the manual?
Questions and answers