Table of Contents
Advertisement
Quick Links
Installation Instructions
for Frontload Washers
Inside.....................................
Washer Dimensions...........................................................
Before You Start................................................................
Installation.........................................................................
Installer Checklist..............................................................
Para bajar una copia de estas instrucciones en español, visite www.speedqueen.com.
Keep these instructions for future reference.
(If this machine changes ownership, this manual must accompany machine.)
Date Purchased ________________
Model Number ________________
Serial Number _________________
www.speedqueen.com
2
2
3
Back Cover
Part No. 802757R4
April 2012
Advertisement
Table of Contents
Related Manuals for Speed Queen 802757R4
Summary of Contents for Speed Queen 802757R4
-
Page 1: Installation Instructions
Para bajar una copia de estas instrucciones en español, visite www.speedqueen.com. Keep these instructions for future reference. (If this machine changes ownership, this manual must accompany machine.) Date Purchased ________________ Model Number ________________ Serial Number _________________ Part No. 802757R4 April 2012 www.speedqueen.com... -
Page 2: Washer Dimensions
Washer Dimensions 24 in. (61 cm) 13.1 in. (33.3 cm) 28 in. (71.1 cm) 26.875 in. (68.3 cm) 2 in. (5.1 cm) FLW222N 1.5 in. (3.8 cm) FLW2221N Figure 1 Before You Start Parts Included An accessories bag has been shipped inside your Supplies washer. -
Page 3: Step 1: Position Washer Near Installation Area
Installation If washer is not level, tilt washer to access the front and rear leveling legs. Loosen the locknuts and adjust Step 1: Position Washer Near Installation legs by screwing into or out of washer base. Area Make sure that the washer does not rock. When washer is level and does not rock, tighten locknuts Move washer as close to the desired area of securely against bottom of washer base. - Page 4 Step 3: Connect Fill Hoses Water pressure must be a minimum of 20 to a maximum of 120 pounds per square inch (138 to 827 kPa) static pressure measured at the faucet. WARNING NOTE: Water pressure under 20 pounds per Under certain conditions, hydrogen gas square inch (138 kPa) will cause an extended fill may be produced in a hot water system...
-
Page 5: Step 4: Connect Drain Hose To Drain Receptacle
Step 4: Connect Drain Hose to Drain Receptacle COLD Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp and by removing the shipping tape. Install the drain hose into the drain receptacle (standpipe, wall or laundry tub) following the instructions below. -
Page 6: Standpipe Installation
Standpipe Installation: Place the drain hose into the standpipe. Remove the beaded strap from accessories bag and place around standpipe and drain hose and tighten strap to hold hose to standpipe. Refer to Figure 6. This will prevent the drain hose from dislodging from drain receptacle during use. -
Page 7: Step 5: Remove The Shock Sleeves And Shipping Brace
Step 5: Remove the Shock Sleeves and 4. Replace panel. Shipping Brace 1. Remove panel. FLW2272N FLW2272N Figure 12 FLW2269N FLW2269N Figure 9 2. Remove brace. Five bolts secure brace to machine. For easier removal, remove in order shown. FLW2268N FLW2268N Figure 13 IMPORTANT: The shipping brace, bolts,... -
Page 8: Step 6: Wipe Out Inside Of Washer Drum
Step 6: Wipe Out Inside of Washer Drum WARNING Before using the washer for the first time, use an all- purpose cleaner, or a detergent and water solution, and To reduce the risk of fire, electric shock, a damp cloth to remove shipping dust from inside the serious injury or death, all wiring and drum. -
Page 9: Grounding Information
Grounding Information Step 8: Check Installation The washer must be grounded. In the event of Refer to Installer Checklist on the back cover of this malfunction or breakdown, grounding will reduce the manual and make sure that washer is installed risk of electric shock by providing a path of least correctly. -
Page 12: Installer Checklist
Installer Checklist Fast Track for Installing the Washer (Refer to the manual for more detailed information) • Position Washer Near • Remove the Shock Sleeves Installation Area. and Shipping Brace. FLW2124N CHECK FLW2124N CHECK • Position and • Wipe Out Inside of Level the Washer.