Page 2
When servicing this product, under no circumstances should the original design danger of electrical shock. DO NOT USE A LINE ISOLATION be modified or altered without permission from Zenith Electronics Corporation. TRANSFORMER DURING THIS TEST. Use an AC voltmeter having 5000...
DESCRIPTION OF CONTROLS Monitor Controls Front Panel Controls ON/OFF VOL. MENU INPUT SELECT INPUT SELECT Button Power Standby Indicator Main Power Button MENU Button Illuminates red in standby mode, Illuminates green when the Remote Control Sensor VOLUME ( ) Buttons Monitor is turned on Buttons Connection Options...
DESCRIPTION OF CONTROLS Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the Monitor. - Under certain conditions or if the IR code from the remote is interrupted, a particular remote function may not occur. Repeat remote key presses for functions if necessary.
EXTERNAL EQUIPMENT VIEWING SETUPS atching VCR Setup atching VCR Setup How to Connect - When connecting the Monitor to external equipment, match the colors of connecting ports (Video - yellow, Audio (L) - white, Audio (R) -red). - Connect the VIDEO INPUT socket (yellow) with the BNC-RCA adapter to the VIDEO INPUT on the Monitor. - If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the Monitor.
Page 10
EXTERNAL EQUIPMENT VIEWING SETUPS atching DTV Setup atching DTV Setup - To watch digitally broadcast programs, purchase/connect a digital set-top box. - This monitor supports HDCP (High-bandwidth Digital Contents Protection) protocol for DVI DTV (480p,720p,1080i) mode. How to Connect • Connect DTV set-top box video output to monitor COMPONENT (DVD/DTV INPUT) or to the monitor RGB1 (PC/DTV INPUT), RGB2 (PC/DTV input) connector depending on your set-top box connectors.
EXTERNAL CONTROL DEVICE SETUP - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor.
Page 12
EXTERNAL CONTROL DEVICE SETUP OK Acknowledgement Command Reference List Command Reference List [Command2][ ][Set ID][ ][OK][Data][x] COMMAND 1 COMMAND 2 DATA • (Hexadecimal) The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the 01.
Page 13
EXTERNAL CONTROL DEVICE SETUP 03. Aspect Ratio (Command:c) (Main picture format) 07. Contrast (Command:g) G To adjust screen contrast. G To adjust the screen format. You can also adjust contrast in the Video menu. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Transmission Special menu.
Page 14
EXTERNAL CONTROL DEVICE SETUP Acknowledgement 11. Sharpness (Command:k) [o][ ][Set ID][ ][OK][Data][x] G To adjust the screen sharpness. Data 0 : 4:3 1: 16:9 You can also adjust sharpness in the Video menu. 16. PIP Position (Command:q) Transmission G To select sub picture position for PIP. [k][k][ ][Set ID][ ][Data][Cr] You can also adjust the sub picture position using Data Min: 0 ~ Max: 64...
Page 15
EXTERNAL CONTROL DEVICE SETUP 20. Color Temperature (Command:u) 25. Orbiter (Command:p) G To adjust color temperature. G To control the orbiter function on/off. You can also adjust ACC in the Video menu. Transmission Transmission [j][p][ ][Set ID][ ][Data][Cr] [k][u][ ][Set ID][ ][Data][Cr] Data 0: Orbiter off Data 0: Normal 1: Cool...
IR CODE(NEC Format) How to Connect How to Connect G Connect your wired remote control to the Remote port on the Monitor. Set the CONTROL LOCK to ‘ON’ on the Monitor back panel to operate Monitor with wired remote control. Remote Control IR Code (NEC Format) Remote Control IR Code (NEC Format) G Output waveform...
ADJUSTMENT INSTRUCTIONS 1. Application Object 4. MAX Bias Adjustment These instructions are applied to all of the PDP monitor, RF- 02CA. (1) Input Full White (255 Gray) signal which generated from Pattern Generator into CVBS and RGB1 Input part. (2) Press POWER ON KEY on R/C for adjustment and select MAX-BIAS 2.
ADJUSTMENT INSTRUCTIONS (2) Vs adjustment COLOR 1) Connect + terminal of D.M.M to Vs pin of P805 and ANALYZER connect – terminal to GND pin of P805. TYPE;CA-100 R-L 70 2) Adjust VR1 until DVM reads the same as the voltage labled G-L 70 R-M 128 on the PWB.
ADJUSTMENT INSTRUCTIONS press v, x on R/C in adjustment mode to select R-M or G-M, (2) DDC Data input for Digital-RGB press VOL +, - Key and adjust it until color coordination becomes as below. 1) Connect PC Serial to DVI Cable of JIG for DDC X: 0.290±0.003, Y: 0.300±0.003 Adjustment to RGB2 terminal (DVI Jack).
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film RUN DATE : 2002.12.3 in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible...
Page 25
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION Q401 0TR387500AA CHIP 2SC3875S(ALY) KEC D123 0DD226239AA CHIP KDS226 SOT23 0TR387500AA CHIP 2SC3875S(ALY) KEC 0DD226239AA CHIP KDS226 SOT23 Q402 D801 Q403 0TR150400BA CHIP 2SA1504S(ASY) KEC D802 0DD226239AA CHIP KDS226 SOT23 Q404 0TR387500AA...
Page 26
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION 47UF MVG 16V M 220UF MV 16V 20% C127 0CE476SF6DC C829 0CE227VF6DC 0CE476SF6DC 47UF MVG 16V M 0CE476SF6DC 47UF MVG 16V M C832 C134 0CE476SF6DC 47UF MVG 16V M C835 0CE476SF6DC 47UF MVG 16V M...
Page 27
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION 470UF STD 50V 20% CA102 0CE477DK618 CN137 0CE476SF6DC 47UF MVG 16V M 0CE107DH618 100UF STD 25V M 0CE105SK6DC 1UF MVG 50V M CA104 CN138 CA105 0CE105SK6DC 1UF MVG 50V M CN141 0CE476SF6DC 47UF MVG 16V M...
Page 28
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION 22 OHM 1 / 16 W 1608 5% AR264 0RRZVTA001D RA101 0RS2701K607 2.7K OHM 2 W 5.00% 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% 0RS2701K607 2.7K OHM 2 W 5.00% AR265 RA102...
Page 36
A/V NTSC(TOP) INTERFACE FIX(TOP) PRINTED CIRCUIT BOARD MAIN(TOP) INTERFACE FIX(BOTTOM) FAN CONTROL(TOP) A/V NTSC(BOTTOM) FAN CONTROL(BOTTOM) LOCAL KEY(TOP) AUDIO(TOP) LOCAL KEY(BOTTOM) MAIN(BOTTOM) POWER S/W(TOP) POWER S/W(BOTTOM) AUDIO(BOTTOM) RIGHT SPK(TOP) RIGHT SPK(BOTTOM) PRE-AMP(TOP) PRE-AMP(BOTTOM)