Time Shift + (Dtv Only) - Sharp Aquos LC-80LE940X Operation Manual

Other useful features
Disconnecting the USB device
When you disconnect the USB device, be sure to the
following steps.
For time shift
Go to "HOME" > "TV Menu" > "Setup" > "View
setting" > "Time shift setting" > "Device removal".
NOTE
• This menu item cannot be selected when a USB storage
device for time shift is not registered.
• The USB storage device registration for time shift is cancelled
in the following cases:
− When the USB storage device is removed.
− When another USB storage device is registered for time
shift; only one USB device can be registered for time shift.
For USB media
Press B on the remote control unit while the
"Photo", "Music", "Video" folder or a sub-folder is
selected.

Time shift + (DTV only)

This function enables you to pause the digital TV or satellite
programme you are watching and start watching it again from
the paused scene.
CAUTION
• Do not unplug the AC cord or turn off the MAIN POWER
switch during time shift timer setting or time shift recording.
• When the AC cord is unplugged and the MAIN POWER
switch is turned off:
− The time shift timer setting is cancelled.
− Recorded data is deleted.
• Time shift recording may be automatically stopped when
signal reception is poor.
• Only this TV can playback the programme recorded on the
USB storage device connected to this TV. The programmes
cannot playback on other TV or PC.
SHARP corporation bears no responsibility regarding
compensation for content when recording cannot
does not take place, loss of recorded data or other
direct or indirect damages related to these matters.
Please be forewarned.
E
Buttons for time shift operation
Remote control unit
EXT MEDIA
TV TV INFO INFO
SLEEP SLEEP
Control panel
Control panel
Buttons
Start recording the programme you are
watching.
• You cannot playback the recorded
REC E
programme until approximately three
seconds after pressing REC E to start
recording.
REC STOP H
Stop recording.
I
Playback the recorded programme.
Stop the programme in playback and go
H
back to the real time broadcast (live).
Pause the programme in playback (time
F
shift recording continues).
• This function is released in 15 minutes.
Reverse (each time you press this button,
S
the reverse speed changes in three levels).
Fast forward (each time you press this
J
button, the fast forward speed changes in
three levels).
Jump backward to the previous chapter
K
point*.
L
Jump forward to the next chapter point*.
Playback will resume after jumping
a
backward by the time interval you set in
"Jump time setting" (Page 61).
Playback will resume after jumping forward
b
by the time interval you set in "Jump time
setting" (Page 61).
* Chapter points are fixed at 10 minute increments.
NOTE
• Refer to Regarding "Select recording device" (Page 33)
• Instead of pressing buttons on the remote control unit, most
of the operations shown to the left are also available on the
screen with the control panel. You can call up this control
panel by pressing CONTROL on the remote control unit or
select "Control (Time shift)" from "HOME" > "TV Menu" >
"Setup" > "Option" > "Option for view".
• The "Audio description setting" menu does not work during
time shift playback.
• When the amount of memory used for time shift reaches
"Full" and the blue point is around the left edge of the bar
 
(see and in the Counter section on page 61), you
cannot operate some functions (F (Pause), S (Reverse),
K(Jumping backward to the previous chapter point),
a (Jumping backward by the time interval you set in "Jump
time setting")).
• Time shift recording stops if no operation detected for three
hours.
• When recording operations are not stopped manually,
recording will automatically stop after six hours.
• To release time shift, press REC STOP H, change the DTV/
SAT channel or change "INPUT".
• Some functions do not work during time shift.
• As time shift is not actually a recording function, recorded
data will be reset when the MAIN POWER switch is turned off
or when the AC cord is unplugged.
• Time shift does not start automatically, but starts only when
REC E is pressed or when a time shift timer setting is
started.
• The PIN is required when you use the buttons such as S,
J, K, L, a, b, if you set the PIN and any
options for "Parental rating" except "None" are selected.
• Do not disconnect the USB storage device used for time shift
during time shift operation.
Description
59