Download  Print this page

Craftsman 139.30499 Instructions

3-button remote control.
Hide thumbs
   

Advertisement

Compatible with 315 MHz or 390 MHz
garage door openers manufactured after
January 1, 1993. Make sure the garage
door opener has a working light bulb
because it is a programming indicator.
PREPARE
PROGRAM THE REMOTE CONTROL
1
To enter programming
mode, press the Program
button until the LED on the
front of the remote control
turns on.
Safety Pin or
Paper Clip
4
To exit programming mode, press
any remote control button except
the button that was just programmed.
BATTERY
The LED on your remote will
stop flashing when the
battery is low and needs to
be replaced.
To replace battery, open the
case as shown. Insert
battery positive side up (+).
Replace the battery with
only 3V2032 coin cell
batteries. Dispose of old
battery properly.
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play
with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no
obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross
path of moving gate or door.
OR
Learn
LED
Learn
LED
Green or
Purple
Red/Orange
2
Press and release the
Learn button on
the garage door
opner.
The Learn LED will light.
Within 30 seconds...
5
To test, press the programmed button on the remote control...
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
• DO NOT recharge, disassemble, heat above 212° F
(100° C) or incinerate.

REPLACEMENT PARTS

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20
3-BUTTON REMOTE CONTROL MODEL 139.30499
Locate the Learn button on
the garage door opener.
NOTE: Your garage door
opener may look different.
OR
Learn
LED
Yellow
3
Press and release the remote
control button you want to use...
Check to see if the garage door opener
light bulb blinks. If not, wait for the
remote control LED to light solid then
slowly press and release the remote
control button again. Repeat until the
light bulb blinks.
DO NOT press the button after the
light bulb blinks.
Locate the Program button on
the remote control
.
Program Button
The garage door opener
will activate.
NOTICE: To comply with FCC and or Industry
Canada rules (IC), adjustment or modifications
of this receiver and/or transmitter are prohibited,
except for changing the code setting or
replacing the battery
THERE ARE NO OTHER USER SERVICEABLE
PARTS.
Tested to Comply with FCC Standards for Home
or office use. Operation is subject to the
following two conditions: (1) this device may
not cause harmful interference, and (2) this
device must accept any interference received,
including interference that may cause undesired
operation.

Advertisement

   Related Manuals for Craftsman 139.30499

   Summary of Contents for Craftsman 139.30499

  • Page 1: Replacement Parts

    3-BUTTON REMOTE CONTROL MODEL 139.30499 Compatible with 315 MHz or 390 MHz To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: garage door openers manufactured after • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play January 1, 1993.

  • Page 2

    TÉLÉCOMMANDE 3 BOUTONS MODÈLE 139.30499 AVERTISSEMENT Afin d’éliminer les risques de BLESSURES GRAVES ou de MORT découlant de l’actionnement d’une clôture Compatibles avec les ouvre-portes de garage ou d’une porte de garage : 315 MHz ou 390 MHz, fabriqués après le 1er janvier 1993.

Comments to this Manuals

Symbols: 0
Latest comments: