Craftsman 3-Button Remote Control Manual

Craftsman 3-Button Remote Control Manual

Also See for CMXZDCG453:

Advertisement

Craftsman 3-Button Remote Control Manual

For use with CRAFTSMAN® garage door openers manufactured after January 1, 1993. The garage door opener activates when the programmed button on the remote control is pressed. The remote control can activate up to three garage door openers.

Make sure the garage door opener has a working light bulb because it is a programming indicator.

CMXZDCG453


To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

  • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls.
  • Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
  • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.


This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

PREPARE

PREPARE Step 1

Locate the Program button on the remote control.

PREPARE Step 2

PROGRAM THE REMOTE CONTROL

  1. Press and hold the program button by using the visor clip until the LED on the front of the remote control turns on.
    PROGRAM THE REMOTE CONTROL Step 1
  2. Press and release the remote control button you wish to use the number of times that corresponds with the garage door opener type:
    # of Presses Garage Door Opener Type
    1 Security+ 2.0® (Yellow Learn Button)
    2 Security+® (Purple Learn Button)
    3 Security+® (Red/Orange Learn Button)
    4 Billion Code (Green Learn Button)
    PROGRAM THE REMOTE CONTROL Step 2
  3. Now, press any remote-control button except the button that was selected in Step 2.
    PROGRAM THE REMOTE CONTROL Step 3
  4. Press and release the Learn button on the garage door opener.
    PROGRAM THE REMOTE CONTROL Step 4
    The Learn LED will light. Within 30 seconds...
  5. Press the remote control button programmed in step 2 until the garage door opener lights flash or two clicks are heard.
    PROGRAM THE REMOTE CONTROL Step 5
  6. To test, press the programmed button on the remote control...
    PROGRAM THE REMOTE CONTROL Step 6
  7. Install the visor clip.
    PROGRAM THE REMOTE CONTROL Step 7

BATTERY

If the battery is low and needs replacement, the LED on this remote will not illuminate when the buttons are pressed. To replace battery, open the case as shown. Insert battery positive side up (+). Replace the battery with only 3V CR2032 coin cell batteries. Dispose of old battery properly.

Pry open the case first in the middle (1), then at each side (2 and 3) with the visor clip.

BATTERY


To prevent possible SERIOUS INJURY or DEATH:

  • NEVER allow small children near batteries.
  • If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

  • Replace ONLY with 3V CR2032 coin batteries.
  • DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

REPLACEMENT PARTS

Battery: K010A0020
Visor Clip: K029B0137

To order replacement parts call...
1-888-331-4569
www.craftsman.com

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Brand

Videos

Craftsman Remote Battery Change Video

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Craftsman 3-Button Remote Control Manual

Advertisement

Need Assistance?

Do you have a question about the CMXZDCG453 that isn't answered in the manual? Leave your question here.

Error while submitting your question. Please, reload page and try again.

Thank you! Your question has been received!

Table of Contents