Related Manuals for Lanpro LP-1000
Summary of Contents for Lanpro LP-1000
- Page 1 Wireless - Equipment LP-1000 User Manual Wireless LAN Access Point LP1000_UM_ENB02W LP-1000 Wireless LAN Access Point User’s Manual Version 1.2 www.lanpro.com...
- Page 2 End users must be provided with specific operating instructions for satisfying RF exposure compliance. This product has been certified in France, Germany, Italy, Spain, Sweden, UK, and US. www.lanpro.com...
- Page 3 Manufacturer hereby disclaims any and all liabilities for consequential and incidental damages arising out of or in connection with any breach of this warranty or any other claim with respect to this product, including but not limited to claims of negligence, strict liability in tort or breach of contract. www.lanpro.com...
-
Page 4: Table Of Contents
(POINT TO MULTIPOINT MODE AND POINT TO POINT SETTINGS) Block Diagram Configuration via SNMP manager 4.2.1 Open Access Point SNMP Manager window 4.2.2 Configuration procedure for bridge – blend mode 4.2.3 Wireless Repeater Mode Adjust the best angle of antenna DISABLE IP FILTERING SPECIFICATIONS DEFAULT SETTINGS www.lanpro.com... -
Page 5: Introduction
• Typical applications include hard-to-wire buildings, campuses, hospitals/medical offices, warehouse, security huts, exhibition centers, etc. • Temporary LANs for special projects or occasions - Auditors require workgroups at customer sites. Trade shows, exhibitions, retailers, airline, and shipping companies need additional workstations for the peak periods of data traffic. www.lanpro.com... -
Page 6: Installation
LED flashes, the larger the received signal strength (RSS) . No power or AP Power Power on AP failure. failure. Radio traffic is detected. The heavier the WLAN AP failure. Nil. traffic, the faster the LED flashes. www.lanpro.com... -
Page 7: Connect To A Network
1• ADSL service with dynamic IP addresses: the AP is connected to one of the hub’s LAN ports, standard RJ-45 cables are used to connect among AP, Hub, and ADSL modem. (see Figure 2). Figure 2. AP connect to ADSL Modem through Hub www.lanpro.com... -
Page 8: Install Utilities
RSS test tool. The first two utilities perform the same functions except the password options and physical connections. 1• Insert the supplied CD-ROM in the CD-ROM drive. 2• Run \Utilities\setup.exe in the CD-ROM. www.lanpro.com... - Page 9 Wireless - Equipment - 2.4 GHz - LP-1000ai User Manual version 1.2 3• Follow the prompted instructions to finish the installation. 4• Restart your PC when prompted. www.lanpro.com...
-
Page 10: Install Ap's Driver
AP, and plug the other end of the USB cable into USB port (type A) of the PC. 2. When plugged, your PC should detect the inserted AP automatically and display New Hardware Found on the display box. www.lanpro.com... - Page 11 Wireless - Equipment - 2.4 GHz - LP-1000ai User Manual version 1.2 3. Put the supplied CD-ROM in the CD-ROM drive. 4. The driver installation procedure will guide you through the standard steps from your operating system. www.lanpro.com...
-
Page 12: Configuration
4. The AP’s driver has been installed (refer to Section 2.8). 5. The AP is turned on. Run the AP Utility from Start, Program, Access Point Utilities, and AP Utility. A window AP Utility Application will be displayed. Three buttons allow you to do the following functions. www.lanpro.com... - Page 13 Modify button, a popped-up window allows you to input the new setting. The new settings will be stored to the AP only after you click the Set button. Click the Exit button when completed. Please refer to Section 7 for the detailed information of each setting. www.lanpro.com...
-
Page 14: Snmp Manager
5. RSSTool has been installed (refer to Section 2.7). Run the RSSTool from Start, Program, Access Point Utilities, and RSSTool. A window RSSTool Application will be displayed. Three buttons allow you to do the following functions. • 1 Rescan: Rescan the AP on the same subnetwork. www.lanpro.com... -
Page 15: Web Management
IP address, 192.168.1.100, in the Address field. Then press Enter. 2. A password request page will show, and enter “public” (the default password) in the Password field. Then click the Submit button. Then you can monitor and configure the Access Point. www.lanpro.com... -
Page 16: Configure Ap As Bridge - Blend Mode (Point To Multipoint Mode And Point To Point Settings)
SNMP Manager (see Section 4.2) or the AP utility (see Section 3.1). Figure 4. Wireless Connection via Bridge Mode. Configuration via SNMP manager • 4.2.1 Open Access Point SNMP Manager window See the description in Section 3.2 to open the Access Point SNMP Manager from the PC or NB. www.lanpro.com... -
Page 17: Configuration Procedure For Bridge - Blend Mode
Step 1: Assign Point to Multipoint mode to AP1 · At Access Point SNMP Manager window, click Setup, select Wireless LAN, and then Operational Settings, the Wireless Operational Setting windows will be displayed as follows: • Click on , the following window will be displayed www.lanpro.com... - Page 18 Channel should be the same for all three APs (AP1, AP2 and AP3), so they can be formed as a group and connected to the available bridge AP. And then click on OK button to go back to the Access Point SNMP Manager window. www.lanpro.com...
- Page 19 • Run SNMP Manager from the PC or NB in LAN1. Follow the same procedure as described in step 3 to open the Access Point SNMP Manager window. • At Access Point SNMP Manager window, click Setup, select Bridge, and then IP Configuration. The Bridge IP Configuration window will be displayed. Record the value in MAC Address field. www.lanpro.com...
- Page 20 The Operation Mode window will be displayed. • At Operation Mode window, select Wireless Bridge and Point to Point, and set AP1 MAC address into Remote MAC Address field, then click on OK button to come back to Wireless Operational Settings window. www.lanpro.com...
- Page 21 PC or NB in LAN2 and LAN3 to use LAN1’s DHCP Server. In this mode, it is recommended that the AP1(as the center of the three APs) be equipped with omni-directional or 75 to 90-degree directional antennas, while AP2 and AP3 be equipped with directional antennas. www.lanpro.com...
-
Page 22: Wireless Repeater Mode
Wireless LAN, and then Operational Settings, the Wireless Operational Setting windows will be displayed as follows: • Click on , the following window will be displayed • Select Access Point, finally click on OK button to go back to Wireless Operational Settings window. www.lanpro.com... - Page 23 Channel should be the same for AP2. And then click on OK button to go back to the Access Point SNMP Manager window. Step 3: Assign DHCP server accessing method for AP1. • At Access Point SNMP Manager window, click Setup, select Bridge, and then IP Configuration. The following window will be displayed. www.lanpro.com...
- Page 24 The Primary Port is the path for connecting DHCP Server to get IP address. However, AP2 is connected with DHCP Server via wireless connection, so the setting must be Wireless. • Click File and select Download Changes to download the change to AP2. www.lanpro.com...
- Page 25 , the Operation Mode window will be displayed. • At Operation Mode window, select Wireless Repeater, and set AP1 MAC address into Remote MAC Address field, then click on OK button to come back to Wireless Operational Settings window. www.lanpro.com...
-
Page 26: Adjust The Best Angle Of Antenna
If you know the AP2’s IP address, then type it in the “Remote IP” blank. If you do not know the AP2’s IP address, then click Rescan. Wait for few seconds, and select the right AP name from the pull-down menu. www.lanpro.com... -
Page 27: Disable Ip Filtering
When you finish the step 5, you will get the best angle of antennas. Then AP1 and AP2 can communicate with the best quality. Note: When RSSTool is running, you can’t run SNMP Manager at the same time. DISABLE IP FILTERING Use AP Utility to disable IP Filtering Run AP Utility, then click Configuration. www.lanpro.com... - Page 28 Wireless - Equipment - 2.4 GHz - LP-1000ai User Manual version 1.2 If the item IP Filtering is not Disable, click Modify Select Disable, then click OK Click Set. www.lanpro.com...
- Page 29 Click Yes, then wait for download completion. Exit AP Utility. Use SNMP Utility to disable IP Filtering Run SNMP, then press Setup -> Bridge -> Filtering Un-check IP Routing, then click OK. Press File -> Download Change. Exit SNMP Utility. www.lanpro.com...
-
Page 30: Specifications
6.8” x 5.5” x 1.0” (172.0 x 141.0 x 26.5 mm), without antenna Weight 22.6 oz. (670 grams), excluding power adapter Certificate U.S.: FCC Part 15, Sections 15.247, 15.205, 15.209 Europe: ETS 300 328, ETS 300 826, CE Marked www.lanpro.com... -
Page 31: Default Settings
128-bit WEP value of 40 41 42 43 44 00 00 Key128 4 “00” to “FF” for each field. key 4 00 00 00 00 00 00 The appropriate frame Preamble Type format for transmission Long “Short”, “Long”. to physical layer. www.lanpro.com... - Page 32 The message indicates SNMP Traps Enable “Enable”, “Disable”. the AP’s actions. Remote MAC address for connection in the Preferred BBS operational mode of 00 00 00 00 00 00 “00” to “FF” for each field. Access Point Client or Wireless Bridge. www.lanpro.com...
- Page 33 Server Secret Server during the authentication process. LanPro is a member of the One Network Aliance Group of Companies. LanPro, The Natural Choice in Networking and LanProfessional are US registered brands. LanPro America: 1880 NW 93rd Av, Doral, Florida 33172, USA.