2. This device must accept any interference work is required. Opening or removing received, including interference that may covers may expose you to dangerous cause undesired operation. www.teledex.com I SERIES ANALOG USER GUIDE...
Page 3
The termination on an interface may consist operate the equipment. I SERIES ANALOG USER GUIDE www.teledex.com...
Any changes made by the user not approved by service may be required. But if advance notice is the manufacturer can void the user’s authority to not practical, the telephone company will notify operate the telephone. www.teledex.com I SERIES ANALOG USER GUIDE...
FCC if you believe it is necessary. forward with a serial number beginning with XX. The telephone company may make changes in its For all other models please refer to the Teledex facilities, equipment, operations, or procedures website for legacy product documentation.
I SERIES A SERIES PHONES (ANALOG CORDED) Unpacking Your Telephone CONVERTING FROM DESK TO WALL MOUNT This package should contain the following: The I Series phone can be converted for wall • Handset mounting applications. The conversion is easiest • Line cord when the handset and line cords are not connected.
I SERIES A SERIES PHONES (ANALOG CORDED) Operation 3. To end the call, hang up by placing the handset back in the cradle. VOLUME CONTROL PLACING A CALL USING THE SPEAKERPHONE ADJUSTING THE HANDSET VOLUME (ONLY MODELS WITH SPEAKERPHONE) To the left of the dialpad, locate the volume up/ 1.
I SERIES A SERIES PHONES (ANALOG CORDED) REDIAL If you are talking on the speakerphone and wish to transfer to the handset, pick up the handset To redial the last telephone number dialed: from the cradle. The speakerphone LED will go 1.
I SERIES A SERIES PHONES (ANALOG CORDED) PAUSE KEY 4. Press the FLASH key (see diagram for key location). The PAUSE key can be used to provide a timed 5. Press the STORE key. The selected flash pause between dialed digits within a stored timing is now programmed.
This process only occurs the first force the connection. time a handset is placed on the charging cradle Note: The handset may “beep” when the battery of a new base. is connected. This is not an indication that the www.teledex.com I SERIES ANALOG USER GUIDE...
BATTERY SAFETY INSTRUCTIONS 6. Insert the top two retaining tabs of the mounting brackets into the mounting 1. Use only Teledex-approved battery bracket slots (located near the middle of replacements. the telephone). Then firmly push down to 2.
3. After the call is complete, press the SPKR WHILE IT IS NOT ON THE BASE key to end call. 1. Pick up the handset. 2. Press the line key. The handset will go “off-hook” answering the phone. www.teledex.com I SERIES ANALOG USER GUIDE...
The telephone will key will maintain the connection with that line, activate the line and remove the hold at while dropping the other line. To terminate the the original telephone. I SERIES ANALOG USER GUIDE www.teledex.com...
Pressing the touch bar automatically turns on 2. Press the STORE key (see diagram on the speakerphone and then dials into a user- inside front cover for key location). programmed voice mail system to retrieve messages. www.teledex.com I SERIES ANALOG USER GUIDE...
Care and Maintenance detergents to clean the system. • Keep the telephone dry. If it gets wet, wipe it dry immediately. Liquids might contain minerals that can corrode the electronic circuits. I SERIES ANALOG USER GUIDE www.teledex.com...
INITIATING A NEW CALL telephone jack. The Teledex I Series Trimline is equipped with a WALL MOUNTING hook switch on the handset, so it’s easy to place The phone can be easily wall-mounted by placing...
Do not use line, place or receive the second call. Press the harsh chemicals, cleaning solvents, or strong CONF key to join all three callers. detergents to clean the system. I SERIES ANALOG USER GUIDE www.teledex.com...
Need help?
Do you have a question about the A Series and is the answer not in the manual?
Questions and answers