Making a Distress Call Lift the red cover. Press and hold the button for three seconds. Your radio transmits your boat’s location every few minutes DISTRESS until you receive a response. nOte: if the radio displays Enter User MMSI, cancel the automatic distress call and make a normal voice distress call.
Faire un appel De Détresse Soulevez le couvercle rouge. Maintenez la touche DISTRESS enfoncée pendant trois secondes. Le VHF480 transmet la position de votre bateau à intervalles réguliers de quelques minutes, jusqu’à ce que vous receviez une réponse. Soulevez le couvercle rouge reMarQue : si la radio affiche enter user MMsi (entrer l’isMM de et appuyez sur la...
CóMO haCer una llaMaDa De apurO Levante la tapa roja. Mantenga oprimido el botón por tres segundos. La radio transmitirá la localidad de su nave cada cuantos DISTRESS minutos hasta que reciba una respuesta. nota: si la radio exhibe (Inserte el MMSI del usuario), cancele la llamada de apuro automática y haga una llamada de apuro normal por voz.
Contents Making a Voice Distress Boosting the transMission call .......... 2 power ........12 Faire un appel De Détresse choosing triple watch Vocal ........3 or Dual watch ....13 cóMo hacer una llaMaDa using Fips coDes For De apuro por Voz ....4 weather alerts ....
Page 6
connecting the raDio ... 28 us Marine channels anD Frequencies ......35 connecting the accessorY caBle ........29 canaDian Marine channels anD Frequencies ....37 connecting to a gps receiVer ....... 29 international Marine channels anD connecting to a Frequencies ......38 chartplotter For Data output ........
intrODuCtiOn Submersible Design - Complies with IPX4 water-resistant standards, which means the Features radio is resistant from damage from rain or splashing water. Large, dot matrix display Advanced DSC Class D functions, including Test Calling Channel Select buttons on the microphone. Memory scan mode - Lets you save channels to memory and monitor them in quick succession.
getting starteD what’s included Mounting Bracket and Mounting Hardware Microphone Hanger and Knobs Mounting Hardware Not shown: Spare Fuse DC Power Cord Accessory Cable English...
parts of the radio VOLUME-PWR (power) CHANNEL UP / knob (turn clockwise to CHANNEL DOWN ENT- 1W/25W increase volume) display buttons button Microphone cord 16/9-TRI WX-MEM SQUELCH knob (triple/dual- CALL- button (turn clockwise DISTRESS watch) button MENU to decrease button with button channel noise) CLR-SCAN...
Antenna Accessory Heat sink connector cable (SO238) Red wire ANTENNA 13.8V DC Black wire Power Cable Connector/Cable Connects to... For details, see ... External VHF antenna with a male PL259 (SO238) connector and 50 Ω Antenna Connecting the radio impedance. Minimum 3 ft, 3dB rated connector (see page 28).
Turn the knob clockwise to turn on the radio. As it powers on, the radio displays turning on the radio the user MMSI number; if there is no MMSI set, the radio displays MMSI not entered. VOLUME-PWR When it powers on, the radio selects the last channel used. The radio comes preset to use the UIC channels assigned for the United States.
Watch Mode What It Does Use It When To Turn it on./off... Weather Alert Checks for alerts You want to be conditions in your area. on the last weather made aware of Select WX Alert Mode in channel you severe weather Setup submenu, and then used every seven conditions in your...
Page 13
To transmit, press and hold on the microphone. Release the button when Using the radio in normal mode you are finished talking. PUSH TO TALK For the best sound quality, hold the microphone about two inches from your mouth while you’re talking.
You can activate Weather Alert Watch and Normal mode with both Weather Alert and Triple/Dual Watch Triple/ Dual Watch at the same time. The radio performs both checks at their Monitoring Channel 25 scheduled time. 09 16 09 16 09 16 Triple Watch: Every 2 seconds, the radio checks channels 9 &...
If you activate Weather Alert Watch while operating in scan mode, the radio checks the most Scan mode with Weather Alert Watch recently-used weather channel every seven seconds, then continues scanning the next channel in memory. To turn Weather Alert Watch on or off, press and hold while the radio is idle.
Page 16
You cannot transmit while in weather mode. Using the radio in weather mode To enter weather mode, press Weather mode can filter out alerts that do not affect your location if the location code WX-MEM (FIPS code) of the alert is entered in your radio (see page 13). If you have no FIPS codes programmed into your radio, the radio will notify you of all alerts in any area.
To display the radio call menu, press . To display the radio normal menu, press and using YOur raDiO hold . The menu has the following options: CALL-MENU CALL-MENU Press and hold - Setup USA/CAN/INT Dual/TriWatch GPS Setup FIPS Codes Auto CH SW POS Reply Test Reply...
The squelch feature reduces the level of static on the speaker by filtering out the background setting the squelch level channel noise. At the lowest squelch level, the speaker plays all radio signals, including any noise on the channel. Setting the squelch level higher filters out channel noise and lets only actual radio transmissions through.
nOte: by default, when you change to channel 16, the radio automatically boosts the power to 25 watts. be sure to change the power back to 1 watt if you are not making an Some channels (for example, channels 13 and 67) limit the power of transmission to 1 Watt emergency transmission.
Follow the steps below to edit the list of FIPS codes. You can store up to 30 different FIPS codes in your radio. Press and hold - Use the up and down arrows FIPS Code Setup to adjust each of the six 000000 digits in turn.
Page 21
the radio is in. For example, if you turn on your radio and it is connected to a GPS unit but the GPS is not sending valid data, the radio displays Check GPS. At the 30 minute mark with no GPS data input from the GPS unit, the radio display changes to Input Position. Is GPS Timeframe Display...
1. Display the normal menu and choose the Setup sub-menu. 2. Select GPS Setup and then choose Position Set. 3. The GPS manual input screen displays; the fields to be entered blink. The cursor highlights the hour. Use to set the displayed hours to match coordinated universal time (UTC, also call Greenwich Mean Time and Zulu Time).
Feature Menu Item Function Test Call Test Make sure your radio is working and configured correctly. Name and MMSI Directory Store a list of 20 names and MMSI identification Directory codes for DSC calls. Standby Mode Standby Automatically respond to all DSC calls within an “Unavailable”...
4. When the first digit is correct, press . The cursor moves to the next digit. Enter the remaining eight digits of the MMSI number in the same way. If you make a mistake ENT-1W/25W while entering a number, press to erase the wrong number and the cursor is moved to the left digit.
Follow the steps below to edit the MMSI numbers in your directory: 1. Press to display the call menu. 2. Select Directory. The screen displays any previously-entered MMSI numbers and names. CALL-MENU 3. To add a new MMSI number to the directory, select New. 4.
Page 26
Call type What it does When to use it Individual Calls a single station using the Any time you want to talk to another User MMSI. station. Group Calls all the stations that have the Any time you want with the whole same Group MMSI as yours.
5. The radio displays the MMSI number you are about to call and asks you to confirm. If you want to call the displayed MMSI number, select Send. To cancel the call, select Cancel. 6. The radio automatically switches to channel 70 to transmit the call request. When the other station accepts the call, both radios switch to the selected response channel for voice transmission.
2. The radio displays the list of distress conditions; use choose the nature of your distress, then press and hold for three seconds. CHANNEL UP CHANNEL DOWN DISTRESS Undesignated Sinking Fire Adrift Flooding Abandoning Collision Piracy.Armed Grounding 3. If no MMSI number has been programmed, the radio prompts you to enter your MMSI Overboard Capsizing number.
DSC Call Type Receive Log Information Distress MMSI (or name), position, time, nature code. Distress MMSI (or name), distress MMSI, position, time, nature code. Acknowledge Distress Relay MMSI (or name), distress MMSI, position, time, nature code. Distress Relay MMSI (or name), distress MMSI, position, time, nature code. Acknowledge Geographical MMSI (or name), category code, communication channel number.
Page 30
Press Test Test [Manual] JIM CASSIDY KENT NEWMAN Select[ENT] Back[CLR] If you want to send a test call to a station that is not in your directory, select Manual. The radio prompts you to enter the MMSI number you want to call. Enter the MMSI number the same way you enter directory entries (see page 17).
Press and hold - Test Reply Setup Auto Test Reply Manual Back[CLR] Select[ENT] 4. To disable automatic test call reply, repeat the steps above and select Manual. position request and reply Anytime you need to know where another boat currently is—to find your boating partners, Requesting another station’s position (POS Request) to respond to a request for assistance, etc.—you can send a position request to their radio: 1.
position reply for safety reasons or because they subscribe to a marine towing service. Sometimes—for example, in some competitive situations—you may not want other stations to get your position without your manual confirmation 1. Press and hold to display the normal menu. 2.
channel switching. If you receive an individual call, the radio will respond with an unattended code, just as if the radio were in Standby. 1. Press and hold to display the normal menu. 2. Select Setup and then Auto CH SW. CALL-MENU 3.
5. Remove the bracket from the radio, and use the mounting hardware to secure the bracket to the mounting surface. Hex nut Spring washer 6. Install the radio back into the mounting Washer Mounting bracket. surface Mounting To operate correctly, your radio requires two bracket Connecting the radio electrical connections:...
Use the accessory cable to connect the radio to a GPS receiver, a GPS chartplotter, and an Connecting the accessory cable external speaker. The wiring diagram below shows the connections for each accessory. Accessory cable wires Connects to... Brown: NMEA_OUT (-) Chartplotter NMEA Data Input (-) Green: NMEA_IN (-) GPS receiver NMEA Data Output (-) or GND...
See page 20 to manually set the GPS coordinates. If the radio is receiving valid GPS data, it will automatically set the clock to your local time Configuring the GPS based on the GPS location. You can adjust your local time forward or back one hour if necessary (for example, if you are close to the border of a time zone);...
You can use an external speaker to monitor the radio from a different part of your boat or in Connecting to an external speaker a noisy environment. If you adjust the knob on the radio, it will also adjust the external speaker volume.
Page 38
Problem Things to Try I can transmit, but no one Check your UIC channel settings (see Setting the UIC can hear me. channel mode (USA/CAN/INT) on page 5). The display will flash if the radio is in a watch mode or The display flashes, and I in scan mode.
Interference from the noise generated by the electrical systems of engines is sometimes a engine noise suppression problem with radios. Your radio has been designed to be essentially impervious to ignition noise and alternator noise. However, in some installations it may be necessary to take measures to further reduce the effect of noise interference.
General Power Output 1 watt or 25 watt (user selectable) Power Requirement 25 watts output: 6A@13.8V DC Modulation ±5 kHz deviation Hum and Noise Signal-to- 45 dB@1 kHz with 3 kHz deviation with 1000 Hz Noise modulating frequency (nominal) Audio Distortion Less than 8% with 3 kHz deviation with 1000 Hz modulating frequency Spurious Suppression...
Channel name/description Used for: NON-COMMERCIAL messages about the needs of the ship, including fishing (recreational or voluntary reports, rendezvous, scheduling repairs and berthing ships only) information COMMERCIAL (working messages about the needs of the ship or the business ships only) the ship is engaged in PUBLIC calls to the marine operator at a public coast station.
Page 42
Ch No. RX Freq TX Freq Status Name on display 156.8500 156.8500 Simplex, 1W Govt maritime control 156.9000 156.9000 Simplex Commercial 156.9500 156.9500 Simplex Commercial 161.6000 157.0000 Duplex Port operation 157.0000 157.0000 Simplex Port operation 157.0500 157.0500 Simplex Coast guard only 157.1000 157.1000 Simplex...
*A indicates simplex use of the ship station transmit side of an international duplex channel, and that operations are different from that of international operations on that channel. **Channels 87 & 88 revert from duplex to simplex operation. AIS channels are not supported. Canadian Marine Channels and Frequencies Ch No.
Ch No. RX Freq TX Freq Status Name on display 156.2750 156.2750 Simplex Port operation 156.3250 156.3250 Simplex, 1W Port operation 156.3750 156.3750 Simplex Bridge to bridge 156.4250 156.4250 Simplex Non commercial 156.4750 156.4750 Simplex Non commercial (156.5250 156.5250) DSC Only 156.5750 156.5750 Simplex...
Page 45
Ch No. RX Freq TX Freq Status Name on display 156.5000 156.5000 Simplex Commercial 156.5500 156.5500 Simplex Vessel traffic system 156.6000 156.6000 Simplex Vessel traffic system 156.6500 156.6500 Simplex Bridge to bridge 156.7000 156.7000 Simplex Vessel traffic system 156.7500 156.7500 Simplex, 1W Environmental 156.8000...
no response event Code Transmitter Backup On Transmitter Carrier On Transmitter Carrier On Transmitter Primary On This radio supports NMEA0183 version 4.10. nMea Operation If you have difficulty getting your radio to receive data from your GPS receiver, check the NMEA Input device’s configuration.
The cords on this product and/or accessories contain lead, a chemical known to the State of California lead warning to cause birth defects or other reproductive harm. Wash hands after handling. West Marine works to reduce lead content in our PVC coated cords in our products and accessories.
The product was used as part of any conversion kits, subassemblies, or any configurations not ap- propriate or contemplated for this product or its use. Damage or loss occurring during return shipment of the product to West Marine or its authorized service representative.
Page 52
(as explained here), then we will: At West Marine’s option, we will repair the product or, if we are unable to repair it, we will replace it with a comparable product that is new or refurbished;...
Page 53
Cleaning, polishing, lubricating, replacing filters, tuning, replacing worn parts, using your purchased MaintenanCe is the Owner’s respOnsibilitY product according to the user’s manual, and regularly maintaining your purchased product is your responsibility. Service will be provided to you under the terms of the Plus Protection Plan Contract. Please refer to what iF i purChaseD a plus prOteCtiOn plan? that contract for details on how to obtain service.
Page 56
QUESTIONS? Contact your local West Marine store. Call 1-800-BOATING Visit our website at www.westmarine.com QUESTIONS? Contactez votre magasin West Marine local. Appelez 1-800-BOATING Contactez-nous au www.westmarine.com Watsonville, CA Printed in Vietnam Imprimé au Vietnam U01UT647AZZ(0)