Sony CDX-GT317EE Service Manual page 9

* 1
BUS AUDIO IN
from car antenna (aerial)
Blue/white striped
AMP REM
3
Max. supply current 0.3 A
Left
Right
Left
Right
Connection diagram
1 To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow, and red power input leads.
2 To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
amplifi er
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/MW/SWantenna (aerial)
in the rear/side glass, see "Notes on the control and power
supply leads."
3 To AMP REMOTE IN of an optional power
amplifi er
This connection is only for amplifi ers. Connecting any other
system may damage the unit.
4 To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car fi rst.
• When your car has a built-in FM/MW/SW antenna (aerial)
in the rear/side glass, see "Notes on the control and power
supply leads."
5 To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car fi rst.
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/MW/SW antenna (aerial) in the
rear/side glass, connect the power antenna (aerial) control
lead (blue) or the accessory power supply lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifi ers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit's speaker leads to each other.
Note on connection
If speaker and amplifi er are not connected correctly, "FAILURE"
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
Supplied with XA-C40
L
R
BUS AUDIO OUT
IN REAR/SUB
AUDIO OUT
Fuse (10 A)
2
*
REAR
CONTROL IN
2
White
Black
White/black striped
Blue
Gray
Gray/black striped
Red
Green
Green/black striped
Purple
Yellow
Purple/black striped
Source selector
(not supplied)
XA-C40
BUS
ANT REM
Max. supply current 0.1 A
CDX-GT317EE/GT360
Supplied with the CD/MD changer
RCA pin cord (not supplied)
* 1
AUDIO OUT can be switched SUB or
* 2
REAR. For details, see the Operating
Instructions.
1
2
4
5
9