Page of 16

Husqvarna 136, 141 Instruction Manual

Husqvarna brush cutter instruction manual.
Hide thumbs
Instruction Manual
Manuel d'instructions
Betriebsanweisung
Manual de instrucciones
English
Please read these instructions carefully make sure you understand them
before using this unit.
Français
Avant d'utiliser cet appareil, veuillez lire attentivement les instructions et
assurez--vous de les avoir comprises.
Deutsch
Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch.
Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen
verstanden haben.
Español
Lea atentamente las instrucciones y asegúrese de entenderlas antes de
utilizar esta unidad.
R
136/141
530088185
11/11/02

   Related Manuals for Husqvarna 136, 141

   Summary of Contents for Husqvarna 136, 141

  • Page 1

    Instruction Manual Manuel d’instructions Betriebsanweisung Manual de instrucciones English Please read these instructions carefully make sure you understand them before using this unit. Français Avant d’utiliser cet appareil, veuillez lire attentivement les instructions et assurez--vous de les avoir comprises. Deutsch Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch.

  • Page 2

    IDENTIFICATION (WHAT IS WHAT?) 1. Cylinder Cover 2. Front Handle 3. Front Handguard 4. Starter Cover 5. Chain Oil Tank 6. Starter Handle 7. Carburator Adjusting Screw 8. Choke Control 9. Rear Handle 10. ON/OFF Switch 11. Fuel Tank 12. Muffler IDENTIFICATION OF SYMBOLS WARNING! saw can be dangerous! Care-...

  • Page 3

    WARNING: Always disconnect spark plug wire and place wire where it can- not contact spark plug to prevent accidental starting when setting up, transporting, ad- justing or making repairs except carburetor adjustments. Because a chain saw is a high-speed wood- cutting tool, special safety precautions must be observed to reduce the risk of accidents.

  • Page 4

    S Mix and pour fuel in an outdoor area on bare ground; store fuel in a cool, dry, well ventilated place; and use an approved, marked container for all fuel purposes. Wipe up all fuel spills before starting saw. S Move at least 10 feet (3 meters) from fuel- ing site before starting engine.

  • Page 5

    Elbow locked Thumb on underside of handlebar S Keep a good, firm grip on the saw with both hands when the engine is running and don’t let go. A firm grip will help you reduce kickback and maintain control of the saw. Keep the fingers of your left hand encir- cling and your left thumb under the front handlebar.

  • Page 6

    SAFETY NOTICE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people.

  • Page 7

    S Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar. S Fit chain drive links in bar groove. S Pull the bar forward until the chain is snug in the guide bar groove. Ensure all drive links are in the bar groove.

  • Page 8

    To stop the engine move the ON/STOP switch to the STOP position. To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object. Use only 15”---18” of rope per pull. Hold saw firmly while pulling starter rope Starter rope handle Left hand...

  • Page 9

    Braking function control CAUTION: The chain brake must be checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

  • Page 10

    NOTCH CUT AND FELLING THE TREE S Make notch cut by cutting the top of the notch first. Cut through of the tree. Next complete the notch by cut- ting the bottom of the notch. See illustra- tion. Once the notch is cut, remove the notch of wood from the tree.

  • Page 11

    First cut on compression side of log Second cut Second cut First cut on compression side of log BUCKING WITHOUT A SUPPORT S Overcut through of the diameter of the log. S Roll the log over and finish with a second overcut.

  • Page 12: Cleaning The Air Filter

    S Next make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch collar from the truck of the tree. Second cut Third cut Collar Pruning technique SERVICE WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

  • Page 13

    S Before storing, drain all fuel from the unit. Start engine and allow to run until it stops. S Clean the unit before storing. Pay particular attention to the air intake area, keeping it free of debris. Use a mild detergent and sponge to clean the plastic surfaces.

  • Page 14

    EU Declaration of Conformity relating to 2000/14/EC We, Poulan/Weed Eater, Division Electrolux North America, Inc., Texarkana, TX, 75501, USA, Tél. : +1 903 223 4100, declare under sole responsibility that the Husqvarna models 136/141 chain saws were assessed in accordance with Annex V of the DIRECTIVE and from serial numbers 2001--305(N or D)00001 and onwards, conforms to the provisions of the DIRECTIVE.

  • Page 15

    Automatic Weight Without bar and chain, kg 4,6 CHAIN Length Pitch Inches Inches Tip Radius 0,325 10T Husqvarna H30 0,325 10T Husqvarna H30 0,050/ 0,325 YEAR OF CONSTRUCTION: MANUFACTURER’S ADDRESS: Noise levels Equivalent (see note 1) noise pressure level at operator ’s ear,...

  • Page 16

    We hope you find the links below useful. For further gardening information visit Blower Vacs Brush cutters Cultivators Cylinder lawn mowers Electric Fertiliser chainsaws spreaders Garden tractors Garden vacuums Hover mowers Husqvarna chainsaws Lawn scarifiers Lawn tractors Petrol hedge Ride on lawn cutters mowers Ryobi strimmers Scarifiers Westwood Brush Cutters tractors...

This manual also for:

136

Comments to this Manuals

Symbols: 0
Latest comments: