Table of Contents
Advertisement
Listening to USB mass storage device/MP3 player (continued)
Notes:
G This unit only supports "MPEG-1 Audio Layer-3" format. (Sampling Frequency is 32, 44.1, 48kHz)
G Playback order for MP3 files may differ depending on the writing software used during file download.
G Bitrate which is supported by MP3 is 32~320 kbps, WMA is 64~160 kbps.
G For MP3/WMA files, please put ".MP3" ".WMA" extension. Files cannot be played back if there is no MP3/WMA
extension.
G Playlists are not supported on this unit.
G This unit can display Folder Name or File Name up to 32 characters.
G Maximum total number of MP3/WMA files is 65025.
G Total number of folders read is 999 including folder with non-playable file. However, the display shows only folder with
MP3 files.
G The display playback time may not be displayed correctly when playing back a variable bitrate file.
G The ID3TAG information supported are TITLE, ARTIST and ALBUM only. Title name, artist name and album name can
be displayed by pressing the DISPLAY button during file playback or pause mode.
G WMA meta tag also supports title, artist and album name which are recorded in WMA files. Copyright protected WMA
files cannot be played back.
Listening to the radio
I Tuning
1
Press the ON/STAND-BY button to turn the power on.
2
Press the FUNCTION button on the main unit or
TUNER button on the remote control repeatedly to
select FM Stereo, FM Mono or AM.
3
Press the TUNING (
control to tune in to the desired station.
G Manual tuning:
Press the TUNING (
tune in to the desired station.
G Auto tuning:
When the TUNING (
more than 0.5 seconds, scanning will start
automatically and the tuner will stop at the first
receivable broadcast station.
Notes:
G When radio interference occurs, auto scan tuning may
stop automatically at that point.
G Auto scan tuning will skip weak signal stations.
G To stop the auto tuning, press the TUNING (
button again.
G When an RDS (Radio Data System) station is tuned in,
the frequency will be displayed first, and then the RDS
indicator will light up. Finally, the station name will
appear.
G Full auto tuning can be achieved for RDS stations
"ASPM", see page 10.
To receive an FM stereo transmission:
G Press the TUNER button to select stereo mode and
"ST" indicator will be displayed. "
appear when an FM broadcast is in stereo.
G If the FM reception is weak, press the TUNER button to
extinguish the "ST" indicator. The reception changes to
monaural, and the sound becomes clearer.
or
) button on the remote
or
) button repeatedly to
or
) button is pressed for
or
" and " " will
I Memorising a station
You can store 40 AM and FM stations in memory and recall
them at the push of a button. (Preset tuning)
1
Perform steps 1 - 3 in "Tuning".
2
Press the MEMORY
button.
3
Within 30 seconds, press the PRESET (
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
4
Within 30 seconds, press the MEMORY button to store
that station in memory. If the "MEMORY" and preset
number indicators disappear before the station is
memorised, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change a
preset station. When a new station is stored in the
memory, the station previously memorised for that
preset channel number will be erased.
Note:
The backup function protects the memorised stations for a
few hours should there be a power failure or the AC power
lead becomes disconnected.
I To recall a memorised station
Press the PRESET (
seconds to select the desired station.
I To scan the preset stations
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
1
Press the PRESET (
seconds. The preset number will flash and the programmed
stations will be tuned in sequentially, for 5 seconds each.
)
2
Press the PRESET (
station is located.
I To erase entire preset memory
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Whilst pressing down the
BY button until "Tuner Clear" appears.
TUNING
9
or
or
) button for less than 0.5
or
) button for more than 0.5
or
) button again when the desired
button, press the ON/STAND-
) button
Advertisement
Table of Contents
