Table of Contents
Advertisement
System Setup
SCAN SVR: ON/OFF
Rotate the [VOLUME[ knob to choose SCAN
SVR (screen saver) ON or OFF.
SCROLL: ON/OFF
For track information that is longer than the
display panel:
When SCOLL is
ON.
the
LCD
will scroll the
ID3 TAG information across
the
display, e.g.:
TRACK->FOLDER->FILE->ALBUM-> TITLE-
>ARTIST-> TRACK->
...
When SCROLL is
OFF.
the
LCD
will display
one of the ID3 TAG
information,
the default
is TRACK
.
but
user can adjust it to other ID3
TAG information
by
press [DISP) button
.
S-CTRL (I POD mode): ON/OFF
Rotate
the
[VOLUME]
knob to choose
S-CTRL(Simple control) ON or
OFF.
* Refer to P 11 .
PANDORA: ON/OFF
Select OFF if the
Pandora
application has
not
been installed on your iPod touch or
iPhone.
DIMMER: ON/OFF
Rotate the [VOLUME) knob to choose
DIMMER ON or
OFF.
• ON:
LCD dimmer is active when small
light
of vehicle is turned ON.
•
OFF: LCD
always maximum brightness
regardless of the vehicle small
light.
Audio Setup
Press
the
[
P
]
button
to enter sound effect
setting
mode.
First press shows current
EO.
Rotate
the
[VOLUME] knob to changes
BEAT
EO
in
this
order:
OFF-> B-BOOST
->IMPACT-> EXCITE->
CUSTOM
Rotate the (VOLUME] knob
to
changes
CUSTOM
.
and press the
[VOLUME]
knob
,
the press [
~
)
or [
.,.....
)
button
to select
it including: BAS-G -> BAS-F -> BAS-Q ->
MID-G
->
MID-F
->
MID-Q
-> TRE-G
->
TRE-F.
rotate the
[VOLUME]
knob
to
select a value.
BAS-G
I
MID-G
I
TRE-G: (-7)-
(+7)
BAS-F:
50/100/200
BAS-0: 0.7/1/1.4/2
MID-F:
500/1 K/2K
MID-0:
0.7/1/1.4/2
7
CZ302
REARIS-W
Rotate the [VOLUME) knob to choose
REAR or S-WOOFER
(SUB-WOOFER).
SW PHASE
Rotate the [VOLUME[ knob to choose
SUBWOOFER phase REVERSE or
NORMAL.
TEL-SW
Rotate the [VOLUME[ knob to choose
MUTE, ON or OFF.
• MUTE:
The sound
from this
unit is muted during
telephone calls.
•
OFF:
This unit continues normal operation even
when the cellular phone is
used.
•
ON:
You can
listen
to your telephone calls from
the speakers connected to this
unit.
*When
listening
to your calls on your car
speakers.
you can adjust
the
volume by
turning the [VOLUME]
knob.
BEEP: ON/OFF
Rotate
the [VOLUME) knob to choose
button beep sound ON or
OFF.
12124H
Rotate the [VOLUME[
knob to choose time
format:
12 or 24
hours.
TRE-F:
5k/1 Ok/15k
TRE-Q 0.7/1/1.4/2
Press the [ P]
button,
then press [
~
) or
[ .,.....
) button to select USER preset
including:
BALANCE->
FADER->
M-B EX->
LPF(Iow
pass filter) -
>
S-W VOL (Subwoofer
Volume)
.
rotate the
[VOLUME)
knob
to
select a value.
BALANCE:LEFT
1-7->CENTER->RIGHT
1-7
FADER:FRONT 1-7->CENTER->REAR 1-7
M-BEX:
ON/OFF
LPF: THROUGH/60/90/120
HPF:THROUGH/60/90/120
SUBW VOL (-6)-(+6)
Radio Operations
Select
tuner
as playing
source
Press [SAC I<.!>) button once or more to
enter
RADIO
mode.
Selecting the radio band
Press the
[BAND
/IC
J
button on
the
panel
or on the remote control to select one radio
band among FM1.
FM2.
FM3.
AM
.
Manual tuning
During manual tuning
.
the frequency
will be
changed in
steps.
Press the
[1+11)
or[~)
button
on
the
panel
to tune in a higher
/
lower station.
Press the
(1+11]
or
(~]
button
on the
remote control to select preset stations.
Auto tuning
Press and hold
the
[
~+~~]
or
[
~]
button
to seek a higher
I
lower station.
To stop
searching,
repeat
the
operation
above or press other buttons having radio
functions.
Note:
When a station is
received,
searching stops
and the station is
played.
Preset scan
Preset scan
receives the
stations stored
in
preset memory
in
order.
This
function is
useful
when searching for a desired station
in
memory.
1.
Press
the
[PS/AS]
button.
2.
When a desired station is tuned
in,
press
the
[PS/AS]
button again
to
continue
receiving that
station.
Note:
Be careful not
to
press and hold the [PS/AS]
button
for
1 second or
longer.
otherwise the
auto store function will begin and the unit
starts storing stations.
Auto store
Only stations with sufficient signal strength
will be detected and stored in the memory.
Press and
hold
the [PS/AS)
button
(1 sec.)
to start automatic station
search.
To
stop auto
store.
press other buttons
having radio
functions.
Notes:
1
.
After auto store. the previous stored
stations will be
overwritten.
2.
The
unit has
4
bands.
such as FM1
. FM2,
FM3 and AM
.
FM3 and AM can store
by AS function
.
Each
band
can store 6
stations,
CZ302 can store 24 stations
in total.
Manual
store
When one expected
radio
station has been
detected,
press and hold number button 1-6
to
store it in
the
memory.
Recall the
stored stations
Press one
numeric button
among
1
to 6 on
the panel to select the corresponding stored
station.
Local
seeking
When LOCAL seeking is
ON,
only those
radio
stations with strong radio signal could
be
received.
To
select
LOCAL function
.
press and hold
the [ DISP]
button on the front
panel,
then
press
[
~]
button repeatedly
until LO
or
OX
displays on the
screen,
and rotate
the
(VOLUME]
knob to select
Local
or Distant
mode.
Note:
The number of radio stations
that
can be
received will decrease after
the
local seeking
mode
is
ON.
Hide quick links:
Advertisement
Table of Contents
