TITAN 1080p-500, 1080p-250 Digital Projection User Manual Declaration of Conformity Directives covered by this Declaration 2004/108/EC Electromagnetic Compatibility Directive. 2006/95/EC Low Voltage Equipment Directive. Products covered by this Declaration Large screen video projector type The CE mark was fi rst applied in:...
Page 3
TITAN 1080p-500, 1080p-250 Digital Projection User Manual Declaration of Conformity Directives covered by this Declaration 2004/108/EC Electromagnetic Compatibility Directive. 2006/95/EC Low Voltage Equipment Directive. Products covered by this Declaration Large screen video projector type The CE mark was fi rst applied in:...
Page 4
TITAN 1080p-500, 1080p-250 Digital Projection User Manual...
Product revision • Because we at Digital Projection continually strive to improve our products, we may change specifi cations and designs, and add new features without prior notice. Projectors built prior to this revision of the User Manual may therefore not include all the features described.
Page 6
TITAN 1080p-500, 1080p-250 Important Information Digital Projection User Manual General precautions Notes Do not open the cabinet. There are no user serviceable parts inside. Use only the power cable provided. Ensure that the power outlet includes a Ground connection, as this equipment MUST be earthed.
Page 7
TITAN 1080p-500, 1080p-250 Digital Projection User Manual Important Information Installation precautions Notes Connect the LAN cable only to a computer LAN connection. Other similar connectors may have a dangerously high voltage source. The projector must be installed only by suitably qualifi ed personnel, in accordance with local building codes.
Page 8
RF Interference The Federal Communications Commission does not allow any modifi cations or changes to the unit EXCEPT those specifi ed by Digital Projection in this manual. Failure to comply with this government regulation could void your right to operate this equipment.
Page 9
TITAN 1080p-500, 1080p-250 Digital Projection User Manual Important Information Digital Projection Contact details Notes Digital Projection Limited, Greenside Way, Middleton, Manchester M24 1XX, UK. Registered in England No. 2207264, Registered Offi ce: as above +44 (0) 161 947 3300 +44 (0) 161 684 7674 Email enquiries@digitalprojection.co.uk, service@digitalprojection.co.uk...
Page 10
TITAN 1080p-500, 1080p-250 Important Information Digital Projection User Manual Page x July 2007...
Titan 1080p-500, 1080p-250 User Manual Contents Declaration of Conformity ........................ii Important Information Symbols used in this guide ........................v ..............................v Warnings ............................v Trademarks Product revision ............................v Manual revision ............................v General precautions ..........................vi Installation precautions ........................vii Operation and confi guration precautions ..................
TITAN 1080p-500, 1080p-250 Table of Contents Digital Projection User Manual Mounting the projector ........................2.15 ......................... 2.15 Chassis adjustment ....................... 2.15 Fitting the optional rigging frame Stacking projectors .......................... 2.17 Connecting the projector ........................ 2.18 ..........................2.18 Signal Inputs ......................2.19 Control connection examples ...........................
Page 13
TITAN 1080p-500, 1080p-250 Digital Projection User Manual Table of Contents Using the control keys ........................4.10 ............................4.10 Power ............................4.10 Shutter .......................... 4.10 On-Screen-Display ............................4.10 Focus ............................. 4.10 Zoom ............................... 4.10 Shift ........................4.11 Auto-detect input mode ...........................4.11 Source information ...............................4.11...
Page 14
TITAN 1080p-500, 1080p-250 Table of Contents Digital Projection User Manual Geometry menu ..........................4.24 .......................... 4.24 Horizontal Position ..........................4.24 Vertical Position ........................... 4.24 Aspect Ratio ......................4.25 User Horizontal Aspect Ratio ....................... 4.25 User Vertical Aspect Ratio ............................4.25 Keystone ............................
Page 15
TITAN 1080p-500, 1080p-250 Digital Projection User Manual Table of Contents 6. Maintenance Changing the lamp module ......................6.2 Changing the air fi lter ........................6.3 Cleaning ..............................6.4 ............................6.4 Projector ..............................6.4 Lens ........................... 6.4 Lamp module 7. Appendix Troubleshooting ..........................
Page 16
TITAN 1080p-500, 1080p-250 Table of Contents Digital Projection User Manual Page xvi July 2007...
Page 17
1. Introduction Contents What’s in the box? ..........................1.2 Key features of the projector ......................1.3 Getting to know the projector ......................1.4 ......................1.4 Front panel, – lens and power ......................1.4 Rear panel – lamp and air fi lter ....................
TITAN 1080p-500, 1080p-250 1. Introduction Digital Projection User Manual What’s in the box? Notes • Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Lenses are optional. Order lenses from your Digital • You should save the original box and packing materials, in case you ever need Projection dealer.
1. Introduction Key features of the projector Notes Congratulations on your purchase of the Digital Projection Titan 1080p-500 or 1080p-250 projector. Digital Projection International, Texas Instruments’ fi rst DLP™ partner and the original innovator of the 3-chip DLP™ projector, proudly introduces the Titan 1080p.
TITAN 1080p-500, 1080p-250 1. Introduction Digital Projection User Manual Getting to know the projector Notes Front panel, – lens and power Air outlet For more detailed information Air inlet - about lenses, see around lens section 2. Installation Front Infra-red window...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 1. Introduction Side panel – connection and control Notes For information about how to connect the projector, see Connecting the projector in section 2. Installation, and Connections in section 7. Control panel Appendix.
Page 22
TITAN 1080p-500, 1080p-250 1. Introduction Digital Projection User Manual Page 1.6 July 2007...
Page 23
2. Installation Contents Screen requirements ......................... 2.2 ............................2.2 Aspect ratio ......................2.2 Fitting the image to the DMD ....................... 2.2 Images displayed full width ......................2.2 Images displayed full height ........................2.3 Diagonal screen sizes ......................2.4 Fitting the image to the screen ....................
TITAN 1080p-500, 1080p-250 2. Installation Digital Projection User Manual Screen requirements Notes Aspect ratio The images are shown here scaled automatically by the Fitting the image to the DMD projector. If the source image supplied to the projector is smaller than 1920 x 1080 pixels, then the image will not fi...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 2. Installation Diagonal screen sizes Notes Screen sizes are sometimes specifi ed by their diagonal size (D) in inches. When dealing with large screens and projection distances at different aspect ratios, it is more convenient to measure screen width (W) and height (H).
TITAN 1080p-500, 1080p-250 2. Installation Digital Projection User Manual Fitting the image to the screen Notes It is important that your screen is of suffi cient height and width to display images at all the aspect ratios you are planning to use.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 2. Installation Positioning the screen and projector Notes For optimum viewing, the screen should be a fl at surface perpendicular to the fl oor. The bottom of the screen should be 1.2m (4 feet) above the fl oor and the front row The projector should be of the audience should not have to look up more than 30°...
TITAN 1080p-500, 1080p-250 2. Installation Digital Projection User Manual Choosing a lens Notes A number of lenses are available for use with the projector. Which lens you choose will depend on the screen size, image aspect ratio, projection distance and light The High Brightness lenses output.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 2. Installation Choosing a lens using the lens charts Notes Use the charts on this page and on the following pages to choose which lens best suits your application. This chart has a TRF of 1.0, for use with the following images: Full width images, including 2.35:1, 1.85:1 and 16:9 (native resolution)
TITAN 1080p-500, 1080p-250 2. Installation Digital Projection User Manual Lens charts continued Notes Full height image 1.66:1 (Vista) This chart has a TRF of 1.07, Use the chart below to choose which lens best suits your application. for use with the following...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 2. Installation Lens charts continued Notes Full height image 4:3 This chart has a TRF of 1.33, Use the chart below to choose which lens best suits your application. for use with the following...
TITAN 1080p-500, 1080p-250 2. Installation Digital Projection User Manual Lens charts continued Notes Full height image 5:4 This chart has a TRF of 1.42, Use the chart below to choose which lens best suits your application. for use with the following...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 2. Installation Choosing a lens by calculation Notes For any screen size not listed above, or if you need to be more precise, then use the calculations below. The Throw ratio for a particular •...
TITAN 1080p-500, 1080p-250 2. Installation Digital Projection User Manual Useful lens calculations Notes The Throw ratio for a particular The following lens calculations may be useful: lens is fi xed, but assumes that the image fi lls the width of the DMD.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 2. Installation Fitting the lens Notes • Turn the lens release lever anti-clockwise so that it is pointing upwards, to open the lock. • Remove the rear lens cap from the lens. Make sure the rear lens cap is •...
TITAN 1080p-500, 1080p-250 2. Installation Digital Projection User Manual Shifting the image Notes For more information on using The normal position for the projector is at the centre of the screen. However, you the Lens shift feature, see can set the projector above or below the centre, or to one side, and adjust the image section 4.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 2. Installation Mounting the projector Notes The projector is designed to be used on a fl at surface, but the optional rigging frame BEFORE INSTALLING THE will allow it to be suspended from a lighting truss or rigging. The four adjustable feet PROJECTOR, READ ALL THE under the chassis allow the projector to be lowered onto a fl...
TITAN 1080p-500, 1080p-250 2. Installation Digital Projection User Manual Adjusting the rigging frame Notes Coarse adjustment of projector level should be made by adjusting the length of the supporting wires or chains, or by adjusting the position of the truss or rigging.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 2. Installation Stacking projectors Notes The rigging frame is capable of supporting the weight of up to two other projectors, using the built-in frame couplings. The projectors can be stacked on top of each other, or suspended below each other.
TITAN 1080p-500, 1080p-250 2. Installation Digital Projection User Manual Connecting the projector Notes Input Control connection panel connection panel Signal Inputs The following inputs are available: 3. DVI For more information on 2. RGB2 selecting an input source, see section 4. Overview, Using the control keys, and Using the menus.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 2. Installation Control connection examples Notes LAN connection All of the projector’s features can be controlled via a LAN connection, using a For more information about pin standard internet browser package such as Internet Explorer.
TITAN 1080p-500, 1080p-250 2. Installation Digital Projection User Manual Power connection Notes When mains power is fi rst applied, the projector will perform a self-test, then go into Standby mode. The Power indicator on the control panel will show amber until the POWER Use only the power cable on the remote control or the keypad, is pressed for 3 seconds.
3. Getting Started Contents Switching the projector on ....................... 3.2 Selecting an input or test pattern ....................3.2 ..............................3.2 Input ............................3.2 Test pattern Adjusting the lens ..........................3.3 .............................. 3.3 Focus ............................... 3.3 Zoom ..............................3.3 Shift Adjusting the projected image ......................
TITAN 1080p-500, 1080p-250 3. Getting Started Digital Projection User Manual Switching the projector on Notes • Connect the power cable between the mains supply and the projector. For more information about connecting the power cable, see Power Connections, in section 2. Installation.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 3. Getting Started Adjusting the lens Notes For more detailed information Focus about: • - using the control keys on the Press followed by to adjust the focus. remote control or keypad, When adjustment is fi nished, press...
TITAN 1080p-500, 1080p-250 3. Getting Started Digital Projection User Manual Adjusting the projected image Notes Picture settings • Press a key, followed by to adjust these picture settings: The Saturation control is available for Composite, S- Brightness Video and Component inputs only.
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Using the menus ..........................4.15 ..................... 4.15 Navigating menus and submenus ..........................4.17 Menu controls Input menu ............................4.18 ........................... 4.18 Input Source ............................4.19 Presets ..........................4.19 Recall Presets ..........................
Page 49
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Setup menu ............................4.30 ............................4.31 Projector ..........................4.31 Orientation ........................4.31 Control Panel Backlight ........................4.31 Component Video Sync ............................ 4.32 Keystone ..........................4.32 Test Pattern ........................4.33 Global Colourimetry ..........................
Page 50
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Overview Notes Controlling the projector The projector can be controlled from: • the remote control • the keypad • the RS232 input • the Ethernet input For more information about controlling the projector using the RS232 and Ethernet inputs, see Remote communications protocol in section 7.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Input modes and settings Notes Input mode detection The projector can automatically detect the following parameters from the incoming video signal: • line frequency • frame rate • interlace / progressive From these parameters the projector can determine input mode, for example: •...
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Any subsequent changes that you make to the modal settings will be saved in the Notes mode history, with the input mode. Mode Mode library history NTSC NTSC defaults...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Indicators Notes Input status indicators 1. RGB1 3. DVI There are more indicators on the Control panel, and these are 2. RGB2 described on the next page. 6. S-Video Input 4.
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual The control panel Notes Many features are controlled Keypad layout from the menus using the menu navigation keys on the remote The controls on the keypad are identical to those at the top of the remote control, control or keypad.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector The remote control Notes Many features are controlled Layout from the menus using the menu navigation keys on the remote control or keypad. For more information about using the menus, see later in Transmit this section, Using the menus.
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Using the control keys Notes Power • Press POWER and hold for 3 seconds, to switch the projector ON. • Press POWER and hold for 3 seconds, to switch the projector OFF.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Auto-detect input mode Notes • Press to force the projector to re-detect the input mode For more information about (see Input modes and settings, earlier in this section). input mode detection, see earlier in this section, Input modes and settings.
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Input Presets Notes Recall • To recall a set of modal settings that have been saved, press and hold whilst pressing the lettered key A – S. For more information about input modes and input presets, •...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Red, Green and Blue Notes • Press to switch the red, green or blue components OFF The red, green and blue keys or ON. are disabled when the OSD is switched OFF.
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Magnify and pan Notes • The magnify feature utilises a Press Magnify MAGNIFY digital zoom. Used with the pan control, this can be used to: followed by to adjust the size of the picture.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Using the menus Notes Some menu controls can be Navigating menus and submenus accessed directly using the control keys (see earlier in this When the menus are in use and the OSD is ON, the top level menu headings are section).
Page 62
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Notes • Press to open the menu. The blue highlight moves to the fi rst item in the menu, which may be submenu, for example the Projector Setup submenu.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Menu controls Notes Some menus have controls, as shown in the examples below. Some menus items may be greyed out - unavailable due to the effect of settings made in other menus, or due to the type of input signal.
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Input menu Notes Some menu controls can be accessed directly using the To return to the main menu, press up to three times. control keys (see earlier in this section).
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Input menu continued Notes Presets Some menu controls can be accessed directly using the Sixteen sets of parameters can be saved and recalled (A – S). The parameters control keys (see earlier in this saved for each Preset are: section).
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Input menu continued Notes Save Presets Some menu controls can be accessed directly using the • Press to select Save Preset. control keys (see earlier in this section). Press to open the Save Presets A ~ H submenu.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Picture menu Notes Some menu controls can be accessed directly using the To return to the main menu, press up to three times. control keys (see earlier in this section).
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Picture menu continued Notes Gamma Correction Video recordings are often supplied with a gamma adjustment applied. The projector’s gamma adjustment can be used to correct for this. • Press to select Gamma.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Picture menu continued Notes Aspect Ratio • Press to select Aspect Ratio. Aspect Ratio selection can be found in both the Picture and Press to select from: Geometry menus.
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Geometry menu Notes Some menu controls can be accessed directly using the To return to the main menu, press up to three times. control keys (see earlier in this section).
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Geometry menu continued Notes User Horizontal Aspect Ratio • Press to select User H Aspect. Horizontal and Vertical Aspect Ratio adjustments are Press to adjust the slider (internal number – adjust to fi t).
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Geometry menu continued Notes Blanking Blanking curtains can be applied to each edge of the picture. • Press to select Blanking. Press to open the Blanking submenu. Geometry Menu...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Colour menu Notes To return to the main menu, press up to three times. When using the menus, press to hide or From the main menu: reveal the On-Screen-Display.
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Colour menu continued Notes Colour Mode • Press to select Colour Mode. Read the notes on Colour and Press to select from: Global Colourimetry earlier in this section before making...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Colour menu continued Notes Trim • Press to select Trim. The Trim submenu is available only if Global Colour Mode is Press to open the Trim submenu. selected. Trim RGB Lift and Gain...
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Setup menu Notes To return to the main menu, press up to three times. From the main menu: • Press until Setup is highlighted. When using the menus, press...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Setup menu, continued Notes Projector • Press to select Projector. Press to open the Projector submenu. Orientation Setup Menu Projector • Press to select Orientation. Press to select from:...
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Setup menu, Projector continued Notes Keystone Used to correct for distortion caused by the projector being mounted higher or lower than the screen. • Press to select Keystone. Press to adjust the slider (-128 to +127).
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Setup menu continued Notes Global Colourimetry • Press to select Global Colourimetry. • Press to open the Global Colourimetry submenu. Setup Menu Global Colourimetry Some menu items may be...
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Setup menu, Global Colourimetry continued Notes Colour Mode • Press to select Colour Mode. Read the notes on Colour and Press to select from: Global Colourimetry earlier in this section before making...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Setup menu, continued Notes Lamp • Press to select Lamp. Press to open the Lamp submenu. The middle row shows the current lamp setting. Setup Menu Lamp Change Lamp Setting •...
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Setup menu, Lamp continued Notes Lamp Power • Press to select the Lamp Power setting. Press to adjust the Lamp Power from: 80 to 100% in 1% steps Lamp Mode •...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Setup menu continued Notes On Screen Display • Press to select On Screen Display. Press to open the On Screen Display submenu. Setup Menu On Screen Display OSD Position •...
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Setup menu continued Notes Password Entry to the password protected area is available to authorised service personel only. • Press to select Password. Press to open the Password control box.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Setup menu continued Notes Communication • Press to select Comunication. Press to open the Comunication submenu. Setup Menu Comunication Projector Address The projector and the remote control need to be set to matching addresses. Read...
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Setup menu continued Notes Network • Press to select Network. Press to open the Network submenu. Input NETWORK 31-FE-A5-81-20-83 LAN MAC Address Picture Connection Geometry Wired DHCP Colour Setup Menu...
Page 87
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Setup menu, Network continued Notes DHCP • Press to select DHCP Press to open the DHCP control box. Press to select from: Press to apply the new DHCP setting.
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Setup menu, Network continued Notes LAN Subnet Mask • Press to select LAN Subnet Press to open the LAN Subnet control box. LAN IP Subnet cannot be changed if DHCP is set to ON.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Setup menu, Network continued Notes LAN Gateway Mask • Press to select LAN Gateway Press to open the LAN IP Address control box. LAN IP Gateway cannot be changed if DHCP is set to ON.
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Setup menu, Network continued Notes Channel • Press to select Channel. Press to open the Channel control box. The Channel setting is not available if Connection is set to Wired.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Setup menu, continued Notes Restore Defaults • Press to select Restore Defaults. Press Restore Defaults will restore The following message will be displayed. all settings to factory defaults. If you are not sure this is...
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Information menu Notes To return to the main menu, press up to three times. When using the menus, press to hide or From the main menu: reveal the On-Screen-Display.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 4. Controlling the projector Information menu continued Notes Digital Projection Information • Press to select Digital Projection. When using the menus, press to hide or Press to see the DP Information screen. reveal the On-Screen-Display.
Page 94
TITAN 1080p-500, 1080p-250 4. Controlling the projector Digital Projection User Manual Page 4.48 July 2007...
TITAN 1080p-500, 1080p-250 6. Maintenance Digital Projection User Manual Changing the lamp module Notes • Turn the power OFF and allow the lamp to cool for 5 minutes. Always allow the lamp to cool • for 5 minutes before: Unscrew the three door screws, and detach the rear door - the door is tethered, so cannot be removed completely.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 6. Maintenance Changing the air fi lter Notes • Turn the power OFF and allow the lamp to cool for 5 minutes. Always allow the lamp to cool • for 5 minutes before: Unscrew the three door screws, and remove the rear door.
TITAN 1080p-500, 1080p-250 6. Maintenance Digital Projection User Manual Cleaning Notes Turn the projector off before cleaning. Projector Never use strong detergents or solvents such as alcohol Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild or thinners to clean the detergent.
TITAN 1080p-500, 1080p-250 7. Appendix Digital Projection User Manual Troubleshooting Problem Possible solutions The projector will not power up. Check that the mains plug is plugged in and that the mains supply is switched on. Check any external fuses or breakers.
Page 103
Check that the address setting on the remote control is set either to zero, or to the same as the projector. See section 4. Controlling the projector, Communication menu In the event that this troubleshooting guide has not solved the problem, then contact your Digital Projection dealer or service centre. July 2007 Page 7.3...
TITAN 1080p-500, 1080p-250 7. Appendix Digital Projection User Manual Specifi cations Part numbers Projector, 1080p-500 106-241 Projector, 1080p-250 106-242 Rigging frame 104-923 Power cable 10A, Europe 102-163 Power cable 13A, North America 102-165 Power cable 10A, United Kingdom 102-180 Remote control...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 7. Appendix Electrical Inputs RGB1, RGB2, DVI, Composite Video, S-Video, Component Pixel clock up to 165MHz Control inputs 1 x LAN 1 x wifi LAN 1 x RS232 serial: 19200 baud, 8 bits, 1 stop bit, no parity...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 7. Appendix Input modes supported Signal Resolution Refresh Total Horizontal Rate number Frequency ( Hz ) of lines (KHz) SDTV 480i 720 x 480 15.73 576i 720 x 576 15.63 HDTV 480p 720 x 480 31.51...
TITAN 1080p-500, 1080p-250 7. Appendix Digital Projection User Manual Input connections Notes 1. RGB1 input 5 x 75 ohm BNC Used for computer, progressive video and analog HD video. RGsB RGBS RGBHV YCrCb Pr/Cr G + Sync Pb/Cb Sync H Sync V Sync 2.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 7. Appendix 3. DVI-D input Notes 24 way D-type connector TMDS Data 2- pin view of female connector TMDS Data 2+ TMDS Data 2 Shield unused unused DDC Clock DDC Data unused TMDS Data 1-...
TITAN 1080p-500, 1080p-250 7. Appendix Digital Projection User Manual 4. (not used in this projector) Notes 5. Composite video input 1 x 75 ohm BNC PAL or NTSC video 6. S-Video input 4 pin mini-DIN pin view of female connector...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 7. Appendix Control connections Notes LAN connection Use: 10BaseT Unshielded Twisted Pair cable • a straight cable to connect to a The standard wire colours as as follows: hub or network, or White / Orange stripe •...
TITAN 1080p-500, 1080p-250 7. Appendix Digital Projection User Manual Serial control input Notes unused Received Data (RX) The projector is a DTE, so use: Transmitted Data (TX) • a straight cable to connect to a pin view of female connector...
Operation commands and Enhanced commands, contact Message Structure Digital Projection at one of the addresses printed near the front The data type for all data is raw hexadecimal, and all data larger than 1 byte is of this manual, and ask for a formatted little endian i.e.
TITAN 1080p-500, 1080p-250 7. Appendix Digital Projection User Manual Operation Messages Operation messages are constructed using the following format: Header Type Size Oper’n Operation Reserved type 2 bytes 1 byte 2 bytes 2 bytes 1 byte 2 bytes 2 bytes...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 7. Appendix Enhanced Messages Enhanced messages are constructed using the following format: Header Type Size Data type Data length (n) 2 bytes 1 byte 2 bytes 2 bytes 2 bytes 2 bytes Data...
TITAN 1080p-500, 1080p-250 7. Appendix Digital Projection User Manual Operation Command examples Notes All operation commands are located at bytes 9 &10. All values are located at bytes 17 & 18 unless otherwise indicated Spaces in example messages are for visual clarity and should...
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 7. Appendix Source (3702) Notes Projector source select Value Spaces in example messages are for visual clarity and should RGB1 not be sent as part of the message. RGB2 In the example messages the CRC is set to 5858h.
TITAN 1080p-500, 1080p-250 7. Appendix Digital Projection User Manual Brightness (E502) Notes Adjusts Brightness -128 — +127 (00h - FFh) Range: Spaces in example messages are for visual clarity and should Centre (0): 128 (80h) not be sent as part of the message.
TITAN 1080p-500, 1080p-250 Digital Projection User Manual 7. Appendix Contrast (E602) Notes Adjusts Contrast -128 — +127 (00h - FFh) Range: Spaces in example messages are for visual clarity and should Centre (0): 128 (80h) not be sent as part of the message.
TITAN 1080p-500, 1080p-250 7. Appendix Digital Projection User Manual Shutter (CF02) Notes Closes and opens shutter Target Value Spaces in example messages (Set) (Get) are for visual clarity and should not be sent as part of the Shutter Close message.
Need help?
Do you have a question about the Titan 1080p-500 and is the answer not in the manual?
Questions and answers