Wolf W302210I Installation Instructions Manual
Pro series wall hoods
Hide thumbs
Also See for W302210I:
- Installation instructions manual (24 pages) ,
- Planning information (8 pages)
Subscribe to Our Youtube Channel
Related Manuals for Wolf W302210I
Summary of Contents for Wolf W302210I
- Page 2 Before you begin installation, read information is important for the safe The correct voltage, frequency and these instructions completely and and efficient installation of the Wolf amperage must be supplied to the carefully. Pro Series wall hood. appliance from a dedicated, ground- •...
- Page 3 E R I E S A L L E N T I L A T I O N O O D S P R O S E R I E S W A L L H O O D S 22-inch Deep Low Profile Wall Hoods: 12"...
- Page 4 *REAR DISCHARGE IS ONLY APPLICABLE ON 22" WALL HOODS (excluding W302210I and W362210I) manufactured by Wolf AND 24" WALL HOODS USED WITH A WBLOWER-120INT (804702) OR ANY WOLF EXTERNAL BLOWER.
-
Page 5: Hardware Contents
Cabinetry and electrical placement for 22-inch and 24-inch deep Pro Series wall hoods. Shipping Weights for 22-inch Shipping Weights for 24-inch Deep Wall Hoods Deep Wall Hoods Model Number Shipping Weight Model Number Shipping Weight W302210I 57 lbs. W302418 67 lbs. W362210I 63 lbs. W362418 78 lbs. W362210 44 lbs. - Page 6 TO CENTER OF TRANSITION 1) Decide where the ductwork will run between the hood and the outside of the home. Your Wolf hood has an adjustable discharge location which can run vertically or horizon- tally. WIDTH OF HOOD...
- Page 7 8". 5" 1 /2 " DIMENSION IS IMPORTANT NOTE: Wolf recom- mends that the hood be installed a Location of mounting holes for 22-inch wall hood minimum of 30" and a maximum of 36" above the cooking surface.
- Page 8 22-inch wall hoods 24-inch deep wall hoods. The loca- to the rough-in plate assembly prior (excluding W302210I and W362210I) tion of the cut-out is determined by to installing hood to the wall framing. and 24-inch wall hoods used with a the hood installation height.
- Page 9 6) Re-attach rough-in plate/ transition Step 4: Install the Hood assembly to hood shell with screws 1) Align the hood assembly with the removed in step 2. marked location. SOFFIT 7) If installing a remote blower, drill 7/8" hole through the wood CAUTION framing for conduit wires.
- Page 10 TO BOTTOM OF VENTILATION HOOD of cold air into the room. 4) Wolf recommends the hood be installed 30" to 36" above the cook- ing surface. 5) Local building codes may require the use of make-up air. Consult your local HVAC professional for specific 37"...
-
Page 11: Step 1: Install Ductwork
30" 36" 30" 36" (762 - 914) (762 - 914) side of the home. Your Wolf 27-inch TO COOKING TO COOKING SURFACE SURFACE deep hood does not have an adjustable discharge and must COOKING SURFACE discharge vertically. - Page 12 IMPORTANT NOTE: Do not use duct smaller than 10" round. WIDTH OF HOOD IMPORTANT NOTE: Wolf recom- mends that the hood be installed a minimum of 30" and a maximum of 36" above the cooking surface. 27-inch Deep Wall Hoods:...
- Page 13 Step 3: Hood Preparation 1 /2 " If installing a duct cover assembly, see 10" ROUND 1 /4 " duct cover installation on page 18. 1) The hood assembly is shipped 2" 1 /2 with the rough-in plate and the tran- "...
- Page 14 2 7 - I N C H E E P A L L O O D S IMPORTANT NOTE: Do not run Step 4: Install the Rough-In Plate Step 5: Install the Hood remote blower connects through 1) Use rough-in plate assembly to 1) Align both ends of the hood ductwork.
- Page 15 Final Installation connecting means to prevent power from being switched on If the Wolf logo nameplate is to be accidentally. When the service applied to the hood, refer to page 18 disconnecting means cannot be for installation steps.
- Page 16 UL of the hood shell. Use clips on hood IMPORTANT NOTE: Wolf recom- or C/UL. Refer to installation instruc- interior to keep excess power cord mends installing the internal blower tions provided with each blower to away from moving parts.
- Page 17 R E M O T E B L O W E R IMPORTANT NOTE: Before turning STEP 2: Connect Remote Blower Feed 6 inches of ROMEX through the the power on, make sure the blower knockout opening hole and into the NOTE: Always refer to all blower is in the "OFF"...
- Page 18 Additionally, some customers prefer hood installation including not to have a nameplate on their hood location, ducting, electri- hood. For your convenience, Wolf has cal placement and adequacy of created a template for a standardized mounting surfaces. logo location. Please see the back...
- Page 19 • CTBLOWER-60REM (801640) – Wolf wall hoods. factory installed with Models 600 CFM remote blower for 22"D W302210I, W362210I and L282212I. wall hoods (except 30" and 36" wide with blower installed) and 24"D and • 30BAK/DF – 30"W x 38"H •...
- Page 20 Stainless steel duct covers are avail- 12-inch Duct Covers for Wall Hoods able for all Wolf wall hoods. Assembly able in 6 and 12 inches for all Wolf • DUC12COVER30W – 12" duct cover includes 13" stainless steel panel with wall hoods.
- Page 21 D E C O R A T I V E R A I L A S S E M B L I E S Decorative rail assemblies are avail- Platinum Finish: Copper Finish: able for Wolf wall hoods in stainless • RAIL-30/PLT – Decorative rail for • RAIL-30/COP – Decorative rail for steel, platinum, brass and copper 30"...
- Page 22 The information and images are the copyright property of Wolf Appliance Company, LLC, an affiliate of Sub-Zero Freezer Company, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance Company, LLC, an affiliate of Sub-Zero Freezer Company, Inc.
- Page 23 LEFT OUTER EDGE OF HOOD...
- Page 24 , LLC PPLIANCE OMPANY P. O. Box 44848 Madison, WI 53744 800-332-9513 • • www.wolfappliance.com 805048 5/03...
Need help?
Do you have a question about the W302210I and is the answer not in the manual?
Questions and answers