Elecom M-TC01DB series User Manual

Wireless Touch Sensor
BlueLED Mouse
M-TC01DB series
User's Manual
Thank you for purchasing ELECOM's Wireless Touch Sensor BlueLED Mouse "M-TC01DB" Series.
This user's manual explains how to properly and safely use the M-TC01DB Series mouse. Please
read this manual before use and keep it in a safe place where it can be accessed whenever it is
needed.
* Except in certain cases, the M-TC01DB Series is referred to as "this product" in this manual.
Safety Precautions
WARNING
„Meaning of symbols Avoid looking directly at the light of the
sensor as doing so may cause eye
Failure to observe precautions
damage.
may result in serious personal
WARNING
injury or death due to fire, Do not attempt to disassemble, modify
electric shock, or other causes.
or repair this product by yourself, as this
Failure to observe precautions may cause a fire, electric shock or product
may result in damage to other
damage.
CAUTION
equipment or personal injury
Do not put this product in fire, as the
due to electric shock or other
product may burst, resulting in a fire or
causes.
injury.
Prohibited action
Do not connect or disconnect the receiver
unit with a wet hand, modify the receiver
Mandatory action
unit or bend it forcibly, as this may cause a
Situation that needs attention
fire or electric shock.
Always keep the receiver unit out of the
Notes and reference information
reach of children as there is a danger that
Observe these precautions carefully to avoid they may swallow it.
personal injury, damage, fire, and other problems.
WARNING
CAUTION
If a foreign object (water, metal chip, etc.)
Do not place this product in any of the
enters the product, immediately stop using
following environments:
the product and disconnect the receiver
• In a car exposed to sunlight, a place
unit from the PC, and remove the battery
exposed to direct sunlight, or a place
from the mouse. If you continue to use the
that becomes hot (around a heater, etc.)
product under these conditions, it may
• In a moist place or a place where
cause a fire or electric shock.
condensation may occur
• In an uneven place or a place exposed
If this product is generating heat,
to vibration
smoking, or releasing an odour, stop its
• In a place where a magnetic field is
use immediately and shut down your PC.
generated (near a magnet, etc.)
After making sure that the product is not
• In a dusty place
too hot to inflict burns, remove the receiver
unit from the PC and take the batteries
This product does not have a waterproof
out of the mouse. After doing this, contact
structure. Use and store this product in a
the retailer from whom you purchased the
place where the product body will not be
product. Do not continue use as there is a
splashed with water or other liquid.
risk of fire or electric shock.
Rain, water mist, juice, coffee, steam or
sweat may also cause product damage.
Do not drop or hit this product.
If this product is damaged, immediately
stop using the product and disconnect
the receiver unit from the PC, and remove
the battery from the mouse. After doing
this, contact the retailer from whom you
purchased the product.
If you continue to use the product in a
damaged condition, it may cause a fire or
electric shock.
Part Names
• Do not use this product with any device that may
significantly affect other equipment in the event that it
„Mouse
malfunctions.
• If this product is used on a transparent surface such
as glass or a highly reflective surface such as a mirror,
the optical sensor will not function correctly and mouse
cursor movement will become unstable.
• When not using the mouse for one month or more,
disconnect the receiver unit from the PC.
• When you no longer need to use this product and the
battery, be sure to dispose of it in accordance with the
local ordinances and laws of your area.
„Batteries
CAUTION
Use AA alkaline batteries, AA manganese batteries,
or AA nickel hydride rechargeable batteries with this
product.
„Receiver unit
If this product will be unused for a long period of time,
remove the battery to avoid battery leakage and failure.
„Cleaning the Mouse
If the product body becomes dirty, wipe it with a soft, dry cloth.
Use of a volatile liquid (paint thinner, benzene, alcohol,
etc.) may affect the material quality and colour of the
a Left button
product.
Push to tilt the mouse to the left for left-click operation.
Cautions for Wireless Equipment
This product is wireless equipment using the entire range of
the 2.4 GHz band and it is possible to avoid the band of mobile
object identification systems. GFSK is used for the radio wave
method. The interference distance is 10 m.
b Right button
The 2.4 GHz band is also used by medical equipment,
Push to tilt the mouse to the right for right-click operation.
Bluetooth ® , and wireless LAN equipment conforming to the
IEEE802.11b/11g/11n standard.
• Before using this product, check that there are no other "radio
stations"* operating nearby.
• If electromagnetic interference occurs between this product
and other "radio stations*", move this product to another
location or stop using this product.
* Other "radio stations" refer to industrial, scientific and medical
devices using the same 2.4 GHz band as this product, other radio
stations of this type, licenced radio station premises for mobile object
identification system that is used in factory production lines, certain
non-licenced low power radio stations and amateur radio stations.
Preparation before Use
WARNING
• Do not use this product with a device that may have Installing/Replacing the Battery
a serious function or influence.
Before using this product, install two AA batteries in the mouse
There are rare cases where an external radio wave at
body.
the same frequency or the radio wave emitted from
a mobile phone causes this product to malfunction,
Remove the battery cover.
slow down, or fail to operate.
• Do not use this product in a hospital or other
locations where the use of radio waves is prohibited.
The radio waves of this product may affect electronic
and medical devices (e.g. pacemaker).
• The use of a wireless mouse in an aircraft is
Insert the battery.
prohibited by aviation law because doing so may
interfere with flight safety. Turn off the power of the
Ma ke s u re t h at t h e
mouse body before boarding an aircraft and do not
polarity is correct.
use it in the aircraft.
* ELECOM is not liable for any accident or social
damages incurred by the failure of this product.
Package Contents
Install the battery cover.
This product's packaging contains the items listed below. Before
using the product, check that all items are present. We make
every effort to ensure that all products are packaged correctly.
However, in the event that an item is missing or damaged,
„Replacing batteries
contact the retailer from whom you purchased the product.
• Mouse x1 Remove the battery cover.
• Receiver unit x1
• AA alkaline dry battery (for checking operation) x2 Remove the battery by
• User's Manual (this manual) x1
using the battery removal
sheet.
Insert the battery.
Do not mix different types of batteries or use
old batteries with new batteries to avoid battery
leakage and failure.
Install the battery cover.
c Touch sensor
Use the touch sensor for touch and slide motions with your
fingertips.
For details on touch operation, refer to "Using the
Touch Operation" (See reverse).
d Power indicator
When the power turns on, the power indicator lights up in
green for 2 seconds.
e Power switch
When the power is off, hold the power switch down for 3
seconds to turn the mouse on.
When the power is on, hold it down for 3 seconds to turn the
mouse off.
f Click switch
Tilt the mouse to left-click or right-click using this switch.
g Optical sensor
Illuminates blue when the mouse body is turned on. When
the mouse body is moved, this sensor detects mouse
movement.
h Battery cover
This cover is removed to install batteries.
i Battery housing
Batteries are inserted here.
j Battery removal sheet
Used to remove the batteries from the battery housing.
k Receiver unit housing
Used to store the receiver unit.
l USB connector (male)
Connected to a PC USB port.
Turning On and Off the Mouse
„Turning on the mouse
When using this product, turn the mouse body
power on.
Press and hold the power switch for 3 seconds.
The power indicator lights up green for 2
seconds.
„Turning off the mouse
When not using the mouse, turn it off to save
battery power.
To turn off the mouse, press and hold the
power switch for 3 seconds when the power is
on. The power indicator lights up orange and
turns off in 2 seconds.
„Restoring from sleep state
Touch the touch sensor.
To reduce battery drain, the mouse enters sleep
mode automatically if it is left without being operated
for a certain period of time with the power or switch
turned on.
Inserting and Taking Out the Receiver Unit
„Inserting the receiver unit
R e m o v e t h e b a t t e r y
cover.
Place the receiver unit into
the receiver unit housing.
Install the battery cover.
„Taking out the receiver unit
Remove the battery cover.
Take the receiver unit
out of the receiver unit
housing.
Install the battery cover.
- 1 -
®
When using Windows
Check USB ports Checking operation
Check the USB port on your computer. Check that the mouse scrolls up and down correctly in
Windows ® Internet Explorer.
USB port
Click on [Internet Explorer
Internet Explorer
• Any USB port may be used.
Display your favourite web site in Internet Explorer
• This product can be connected to a USB hub.
* The sample website used here is the ELECOM
However, it may not work depending on the power
homepage.
supply capability of the USB hub.
Installing the Receiver Unit
Activate the PC
• If Windows ® prompts you to choose an account (a
user name) when it starts up, be sure to log on using
Touch the centre of the touch sensor and move
an administrator account.
your finger up or down.
• Wait until Windows ® has started up completely.
Insert the receiver unit into the USB port of the PC.
Insert here.
USB port
Receiver unit
The mouse is operating
normally if the screen moves
up and down as you scroll
• Carefully check the orientation of the
the tilt wheel.
connector and the place where you will
connect the receiver unit.
The finger slide motion on the centre part of
• If you feel strong resistance when inserting
the touch sensor may not work with certain
the receiver unit, check that the shape and
applications that do not support the scroll function.
orientation of the connector is correct. Using
excessive force may damage the connector
and cause injury.
The mouse driver is installed automatically.
®
] on the desktop.
® will launch.
®
.
Scrollbar