Subscribe to Our Youtube Channel
Related Manuals for Eusso 200Mbps Powerline HomePlug
Summary of Contents for Eusso 200Mbps Powerline HomePlug
-
Page 1: Ethernet Adapter
200Mbps Powerline HomePlug Ethernet Adapter User Manual Copyright 2008 EUSSO Technologies, Inc. All rights reserved. -
Page 2: About This Manual
200Mbps Powerline HomePlug Ethernet Adapter. Chapter 1 Installing the 200Mbps Powerline HomePlug Ethernet Adapter This chapter describes how to set up the 200Mbps Powerline HomePlug Ethernet Adapter on your local area network (LAN) and connect to the Internet. Package Contents... -
Page 3: Prepare To Install Your Powerline Adapter
Each computer or device to be used on your network has an Ethernet port. Connect a 200Mbps Powerline HomePlug Ethernet Adapter to the Router First, connect a 200Mbps Powerline HomePlug Ethernet Adapter to a LAN port on the router so that the Powerline network can access the Internet. Do not connect the Powerline adapter to a power strip, extension cord, or surge protector as this may prevent it from working properly or degrade the network performance. -
Page 4: Connect Other Ethernet Powerline Adapters
— Power: The power LED turns on. If it does not light, see Chapter 2, “Troubleshooting”. — Power Link: The Power Link LED blinks to indicate that the device is connected to the power line, and that no other Powerline devices have been detected at this stage. - Page 5 All devices on a Powerline network can be managed from one computer. If you add another 200Mbps Powerline HomePlug Ethernet Adapter device to an existing Powerline network, you can install the Powerline encryption utility on the computer connected locally to the new Powerline HomePlug Ethernet Adapter device or on the computer originally used to set up the Powerline network password.
- Page 6 Click Next and shows license agreement declaration. Click Next. Specify where the files will be installed on your computer: Type a new folder name in Destination Folder field or select another location using the Browse options and then click OK. Accept the default location and click Install button to start installation.
- Page 7 Below screen shows the installation status. When the installation is complete, click Finish.
-
Page 8: Powerline Adapter Configuration
Powerline adapter Configuration After the management utility is installed, it will create a folder and shortcut in your Start Menu and on your desktop. Use the Start Menu or Desktop Shortcut to execute the management utility. The utility starts searching for connected Powerline Adapters:... - Page 9 Note: If no Adapters are found, make sure all adapters are connected to the electric circuit. Click “Update List” to search again for available adapters. Note: It is recommended to configure all your 200Mbps Powerline HomePlug Ethernet Adapters at the same time. You can do this with the steps described in...
- Page 10 Multiple adapters configuration ”. If you want to configure all Adapters separately, make sure you start with the adapters in the section “Other Adapters”. Multiple adapters configuration Press and hold the CTRL key of your keyboard and select all adapters you want to configure. The button “Select All”...
- Page 11 You will see the following configuration options: Enter a name for your Powerline network in the field “Identification Network”. To secure your network, enter an encryption key in the field “Encryption Key”.
- Page 12 Note: If you add more Powerline Adapters to your Powerline network later, make sure that the “Net ID” (Network name) and the “Encryption Key” are the same for all adapters. If one of these settings is different than the other configured Powerline Adapter(s), the new Powerline Adapter will not function! You can secure the configuration of the Powerline Adapter.
- Page 13 You will see the following configuration options: Enter a name for your Powerline network in the field “Identification Network”.
-
Page 14: Factory Reset
To secure your network, enter an encryption key in the field “Encryption Key”. Note: When you configure all Powerline Adapters separately, make sure that the “Identification Network” (Network name) and the “Encryption Key” are the same for all adapters. If one of these settings is different than the other configured Powerline Adapter(s), the Powerline network will not function! Enter a name for the current Powerline Adapter in the field “Alias”. - Page 15 Select the “ETH Connected Node” and click the “Factory Reset” button. Note: You can reset only 1 Powerline Adapter at a time. If you select a Powerline Adapter listed in the section “PLC Connected Node”, the “Factory Reset” button is not shown.
- Page 16 You will be notified when the factory default settings are applied. Click “OK” to close the notification window.
-
Page 17: Troubleshooting
Chapter 2 Troubleshooting This chapter gives information about troubleshooting your 200Mbps Powerline HomePlug Ethernet Adapter. After each problem description, instructions are provided to help you diagnose and solve the problem. Basic Functioning After you plug in the Powerline adapter, the following sequence of events should occur: When power is first applied, verify that the Power light is on.
Need help?
Do you have a question about the 200Mbps Powerline HomePlug and is the answer not in the manual?
Questions and answers