To Perform Manual Receive; To Turn Auto Receive On And Off; To Check The Latest Signal Reception Results - Casio 3405 Operation Manual

Operation Guide 3405
Signal reception may not be possible at the distances noted below during certain
times of the year or day. Radio interference also may cause problems with reception.
Mainflingen (Germany) or Anthorn (England) transmitters: 500 kilometers
(310 miles)
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)
Shangqiu (China) transmitter: 500 kilometers (310 miles)
Even when the watch is within the reception range of the transmitter, signal
reception will be impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
See the information under "Signal Reception Troubleshooting" (page E-30) if you
experience problems with time calibration signal reception.
E-20
Your Home City
1 2
HKG Standard Time and 1:00 am 2:00 am
BJS Daylight Saving Time
TPE Standard Time Midnight 1:00 am
SEL
TYO
HNL
Standard Time and Midnight 1:00 am
ANC
Daylight Saving Time
YVR
LAX
YEA
DEN
MEX
CHI
NYC
YHZ
YYT
E-22
About the Signal Strength Indicator
The signal strength indicator shows the strength of the calibration signal being
received. For best reception, be sure to keep the watch in a location where signal
strength is strongest. The signal strength indicator is displayed while an auto or
manual receive operation is in progress.
Receiving indicator
Weak
Signal strength indicator
(Level 1)
Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the signal strength indicator to indicate signal
strength.
E-24

To perform manual receive

1. Enter the Timekeeping Mode (page E-8).
Receiving
2. Hold down D for about two seconds until the receiving
indicator starts to flash on the display. This indicates
that manual receive is in progress.
Time calibration signal reception takes from two to
seven minutes. Take care that you do not perform
any button operations or move the watch during this
time.
If the receive operation is successful, the reception
Receive successful
date and time appear on the display, along with the
ET indicator.
3. After manual receive is complete, press D to return to
normal timekeeping.
The watch also will return to normal timekeeping if you
do not perform any button operation for about one or
two minutes.
E-26

To turn auto receive on and off

1. In the Timekeeping Mode, press D to display the last
successful receive time and date screen (page E-29).
2. Hold down A until the current auto receive setting (
or ) starts to flash. This is the setting screen.
Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press D to toggle auto receive on (
On/Off status
( ).
4. Press A to exit the setting screen.
For information about city codes that support signal
receive, see "To specify your Home City" (page E-12).
E-28
Auto Receive Start Times
3 4 5 6
3:00 am 4:00 am 5:00 am
2:00 am 3:00 am 4:00 am 5:00 am
2:00 am 3:00 am 4:00 am 5:00 am
*Next day
Strong
(Level 3)
) and off
About Auto Receive
The watch receives the time calibration signal automatically up to six times a day
(five times a day for the Chinese calibration signal). When any auto receive is
successful, the remaining auto receive operations are not performed. The reception
schedule (calibration times) depends on your currently selected Home City, and
whether standard time or Daylight Saving Time is selected for your Home City.
Your Home City
1 2
LIS Standard Time 1:00 am 2:00 am
LON Daylight Saving Time 2:00 am 3:00 am
MAD Standard Time 2:00 am 3:00 am
PAR Daylight Saving Time 3:00 am 4:00 am
ROM
BER
STO
ATH Standard Time 3:00 am 4:00 am
Daylight Saving Time 4:00 am 5:00 am
MOW Standard Time 4:00 am 5:00 am
Daylight Saving Time 5:00 am Midnight*
Note
When a calibration time is reached, the watch will receive the calibration signal only
if it is in either the Timekeeping Mode or World Time Mode. Reception is not
performed if a calibration time is reached while you are configuring settings.
Auto receive of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
The watch receives the calibration signal for two to seven minutes everyday when
the time in the Timekeeping Mode reaches a calibration time. Do not perform any
button operation within seven minutes before or after the calibration times. Doing so
can interfere with correct calibration.
Remember that reception of the calibration signal depends on the current time in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the displayed
time actually is the correct time.
Use the signal strength indicator as a guide for checking signal strength and for
finding the best location for the watch during signal receive operations.
Following reception of the time calibration signal and calibration of the watch's time
setting, the receiving indicator will remain on the display in all modes. The receiving
indicator will not be displayed if signal reception was unsuccessful or after you adjust
the current time setting manually.
The receiving indicator is displayed only when the watch is able to receive both time
and date data successfully. It does not appear when only time data is received.
The receiving indicator indicates that at least one of the auto calibration signal
receive operations was successful. Note, however, that the receiving indicator
disappears from the display each day when the first auto receive operation of the
day is performed.
Receive failed If the latest reception fails but a previous reception was
successful, the receiving indicator will be on the display.
Note
To interrupt a receive operation and return to normal
timekeeping, press D.
If there was a previously
successful reception
If no reception was
successful

To check the latest signal reception results

In the Timekeeping Mode, press D to view the last
successful receive time and date. Press D again to
return to the previous screen.
The watch also will return to normal timekeeping if you
do not perform any button operation for about one or two
minutes.
Auto Receive Start Times
3 4 5 6
3:00 am 4:00 am 5:00 am Midnight*
4:00 am 5:00 am Midnight* 1:00 am*
4:00 am 5:00 am Midnight* 1:00 am*
5:00 am Midnight* 1:00 am* 2:00 am*
5:00 am Midnight* 1:00 am* 2:00 am*
Midnight* 1:00 am* 2:00 am* 3:00 am*
Midnight* 1:00 am* 2:00 am* 3:00 am*
1:00 am* 2:00 am* 3:00 am* 4:00 am*
E-21
E-23
E-25
E-27
E-29