Incra TS-LS Owner's Manual

Incremental micro ts-ls table saw fence
Hide thumbs Also See for TS-LS:

Advertisement

INCRA
oWnER'S MAnuAL
ConTEnTS
Safety . . . . . . . . . . . . . . . . . . . .
Rail Assembly . . . . . . . . . . . . . .
Base Mount Assembly . . . . . . . . .
Fence Assembly . . . . . . . . . . . . .
Final Calibration . . . . . . . . . . . . . . 9
Please read this owner's manual and
keep it at hand for reference.
Note: The INCRA TS-LS system consists of
three packages. One of the packages contains
the rails and another, the base mount unit.
These two assemblies are covered fully by this
owner's manual. The third package contains
the INCRA LS Positioner. Read all of this
TS-LS owner's manual and the Safety, Getting
Acquainted and Operations sections of the
LS Positioner manual. If you have also pur-
chased one of the router table extension wings,
complete all assembly instructions in
sion woodworking machine, one you'll be proud
of for years to come. So take a few minutes to
read over the safety information and mounting
instructions, then grab a Phillips screwdriver
and a set of wrenches and let's get started.
2
2
Extension Table . . . . . . . . . . . . . 11
4
6
Maintenance . . . . . . . . . . . . . . . 12
8
Warranty . . . . . . . . . . . . . . . . . . 12
The only table saw
fence with patented
Automatic Lead Screw
Positioning Control
this manual BEFORE attaching the
router table.
In just about an hour or so, you
are going to be operating one
of the most exciting new tools in
today's woodshops. Your table
saw will undergo a transforma-
tion, and what was once an
average saw will emerge a preci-
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TS-LS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Incra TS-LS

  • Page 1: Table Of Contents

    MAnuAL Please read this owner’s manual and keep it at hand for reference. Note: The INCRA TS-LS system consists of three packages. One of the packages contains the rails and another, the base mount unit. These two assemblies are covered fully by this owner’s manual.
  • Page 2: Safety

    SAFETY Important safety instructions for using the INCRA TS-LS Before using the INCRA TS-LS, read and follow all Always keep both hands behind the fence when   of the instructions and safety information in this moving the INCRA TS-LS to a new setting.
  • Page 3 #10 – 32 x ⁄ ” Phillips pan head screw 4 each 4 each ⁄ ⁄ – 16 ” 8 each 8 each thick nylon washer dual pilot rectangular nut #10 – 32 flat washer hex nut INCRA TS-LS Owner’s Manual...
  • Page 4: Rail Assembly

    Note: The blade guard must be reinstalled after you have (See Details 1A and 1B) finished mounting the INCRA TS-LS to your table saw. Attach mounting brackets Attach (4) mounting brackets to the cast iron surface of your table saw using the supplied hardware. See Fig. 1.
  • Page 5 The rail positions described above will provide support for If you wish to customize the setup to suit your needs, just the base of the TS-LS for work on either the left or right slide the rails left or right as necessary. Keep in mind side of the blade.
  • Page 6: Base Mount Assembly

    ” Phillips pan head screws. Insert the screws through each of the (8) holes on the Base support red sub-base on your INCRA LS Positioner Base and loosely panel thread a #10-32 hex nut onto each screw. Slide the hex nuts Base clamp on all (8) screws into the T-slots on the base support panel.
  • Page 7 92” rails. slide the base assembly to any position along the length of the rails - great for accessing a router table extension wing placed to the left of the blade. INCRA TS-LS Owner’s Manual...
  • Page 8: Fence Assembly

    If an adjustment must be made, turn off the saw and NOTE: When removing the TS-LS from your walk to the rear to make the adjustment. table saw, always disengage the rail hooks from the T-slot lip before lifting the TS-LS off the rails. INCRA Woodworking Tools & Precision Rules...
  • Page 9: Final Calibration

    0” under the hairline the 0” mark under the hairline cursor cursor, Fig. 21. Lower the scale back onto the magnetic track. If you want, you can also slide the lexan scale to agree with the stainless steel scale. INCRA TS-LS Owner’s Manual...
  • Page 10 Place LS Positioner on the rails to the left of the saw Moving your TS-LS to the left side of the blade can be quite useful, especially on table saws which have a blade tilt to the right. This feature makes bevel cuts on opposing edges...
  • Page 11: Blade Guard Adjustments

    EXTENSION TABLE If you wish to add a ” thick table board between the fig. 28 right hand extension wing of the table saw and the TS-LS ⁄ ” dia. hole Table board support base mount assembly, begin by making two of the wooden supports like the one shown in Fig.
  • Page 12: Auxiliary Fence Mounting

    In fact, just keeping your the lead screw on both the carriage and the base. A light TS-LS clean is all you need to do to keep the tool in top application of paste wax to the top of the rails from time to shape.

Table of Contents