Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Manual
JP17 & 18 Audio Amp. Select Jumper
MODEM-IN Connector
Onboard AC97 CODEC
CD-IN Connector
32-bit PCI Expansion Slot x3
nd
Supports 2
USB Port
JP14 CMOS Clear Jumper
JP9 & 10 FSB Select Jumper
WOL Connector
IrDA Connector
2Mbit Flash ROM BIOS
Front Panel Connector
ATA/100 IDE Connector x2
FDD Connector
SPP/EPP/ECP
Parallel Port
PS/2 Mouse
Connector
USB Port
PS/2 Keyboard
COM 1 Port
Connector
Game Port
COM 2 Port
MIC-In
Line-In
Speaker Out
Resettable Fuse
Low ESR Capacitor
and Three-Phase Power Solution
CPU Temperature Sensor
462-pin CPU Socket
with Voltage/Frequency Auto-detection
®
®
that supports AMD
Athlon
& Duron
600MHz~1GHz+ CPU
AGP 4X Expansion Slot
CPU Fan Connector
with H/W Monitoring Function
ATX Power Connector
®
AMD
761™ Chipset
DDR SDRAM Socket x2
supports maximum up to 2GB
JP19 System Thermal Sensor connector
JP7 hardware monitor connector
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AOpen MK7A
Summary of Contents for AOpen MK7A
- Page 1 SPP/EPP/ECP Parallel Port PS/2 Mouse Game Port Connector USB Port PS/2 Keyboard COM 1 Port COM 2 Port Connector JP17 & 18 Audio Amp. Select Jumper MIC-In MODEM-IN Connector Line-In Speaker Out Onboard AC97 CODEC CD-IN Connector Resettable Fuse Low ESR Capacitor and Three-Phase Power Solution CPU Temperature Sensor 32-bit PCI Expansion Slot x3...
-
Page 2: Jp14 Clear Cmos
2-3 and 5-6 of JP17, then pin 1-2 and 4-5 of JP18 to enable the audio amplify circuit. Bonus Pack CD x 1 Enable Amp. This Easy Installation Guide x 1 Motherboard x 1 JP18 JP18 JP17 Disable Amp. (Default) PART NO: 49.89C01.001 DOC. NO: MK7A-EG-E0108E JP18 JP17 JP17... -
Page 3: Installing Cpu
Tip: If your system hangs or fails to boot because of SENSOR overclocking, simply use <Home> key to restore the default setting (433MHz) or you can wait the AOpen “Watch Dog Timer” Fan2 Connector reset the system in five seconds and system will auto-detect... -
Page 4: Connecting Ide And Floppy Cables
64M/128M/256M/512M/1GB DRAMs and maximum up to 2GB. IDE LED ACPI & PWR Warning: The MK7A only supports DDR SDRAM, please do not install Speaker Reset the SDRAM on it; this will cause the memory sockets or DDR SDRAM module damage. - Page 5 12. Connecting CD-IN / MODEM-CN Cables 10. Connecting ATX Power Connector The ATX power supply uses 20-pin connector shown below. Make sure you plug in the The CD-IN connector is used to connect CD Audio cable from CDROM or DVD drive to onboard sound. right direction.
-
Page 6: Bios Upgrade
15. AOpen Bonus Pack CD 17. BIOS Upgrade AOpen Easy Flash is much more user-friendly than traditional flash method. The BIOS You can use the autorun menu of Bonus CD disc. Choose the utility and driver and select binary file and flash routine are combined together and you simply run a single file to model name. -
Page 7: Part Number And Serial Number
IDE cable. The problem should be caused by the Check if the system can IDE cables or HDD itself. reboot successfully. Re-install Windows 95, Windows 98 or Windows NT. MK7A is model name of motherboard; R1.00 is BIOS version... - Page 8 Dear Customer, Test Report: We recommend to choose board/card/device from the Thanks for choosing AOpen products. To provide the best and fastest service to compatibility test reports for assembling your PC. our customer is our first priority. However, we receive numerous emails and http://www.aopen.com.tw/tech/report/default.htm...
Need help?
Do you have a question about the MK7A and is the answer not in the manual?
Questions and answers