Advertisement
At the Rear:
⇒
Mode Selector Switch
⇒
Screw Cap Fuseholder
⇒
Voltage Selector
(Not on European Model)
Introduction
Congratulations on the purchase of your new CHAUVET lighting effect. We are confident you will
enjoy many trouble free hours with this unit. To assist with the care and use of the product we
have prepared this short guide.
Operation
Before connecting this unit to the mains power supply for the first time you must first install the
lamps. (See 'Replacing Lamps' for details).
This lighting effect has been designed to function on a mains power supply of either 120V~60Hz
or 230V~50Hz and has been fitted with a suitable power plug for use with your local voltage.
Check the label and voltage selector switch (if fitted) on the unit and the power plug for the
correct voltage.
When connected to the mains power supply the unit should illuminate. This effect has three
modes of operation – static, continuous rotation or sound activated. There is a selector switch at
the rear which determines the mode (see fig.1).
Due to the high operating temperature of halogen lamps it is advisable that the effect be used in
well ventilated areas taking care not to obstruct the air vents. After use allow time to 'cool' for
safety and to ensure lamp life before moving or touching.
The duty cycle for this effect should be no more than 15 minutes on then 15 minutes off.
Installation / Mounting
Although this unit can be used in an upright position, it is recommended that, for safety purposes,
your lighting effect be properly mounted using a suitable hanging clamp and safety cable.
CHAUVET offers a range of items, which are ideal for safe mounting.
Use in a well-ventilated area without obstruction to air vents.
Replacing Effect Dish
Disconnect from main power supply before attempting to replace effects dish.
Simply remove front cover which will reveal the lamp, holder and dish. The dish is held in place
with two small screws, which when removed allow the dish to be manipulated from the motor
Mounting Bracket
Lamp Replacement Cover
Lens
Fig. 1
shaft. Replace with chosen effect dish, tighten screws and replace cover. Remember CHAUVET
also provide a selection of effect dishes which are interchangeable for this unit.
Replacing Lamps
1. Disconnect from main power supply before attempting to replace either lamps or fuse.
2. Ensure that the unit is sufficiently cool, before removing blown lamps.
3. Never touch new lamps with your fingers; use a tissue or a cloth.
In order to replace the lamp, disconnect from main power supply first, and unscrew the lamp
replacement cover, which is highlighted on the diagram (fig.1). Only use the appropriately rated
lamps as use of any other lamp type may cause the unit to be non-operational.
Due to the nature of halogen lamps it is vitally important that you do not touch the new
replacement lamp with your fingers, as this will reduce lamp life considerably. Once again a
tissue or cloth can be used for fitting the replacement lamp.
Finally before using, check that the lamp is housed correctly in the lamp holder and that the lamp
replacement cover has been screwed back into place.
If after replacement of the lamp, the unit is still not working then please contact your dealer or
CHAUVET for servicing.
Replacing Fuses
If the unit does not function at all when connected to the main power supply i.e. the mechanism
does not spin. Then it is highly likely that the fuse has blown.
Disconnect from main power supply before attempting to replace either lamps or fuse.
In order to replace the fuse, disconnect from the main power supply first, and then unscrew the
fuseholder cover to reveal the fuse. The unit has a label attached which indicates the correct fuse
rating and you will also find this listed as part of the specifications for the unit later in this guide. It
is most important that replacement fuses are of the correct rating. Failure to use the correct fuse
could damage the lighting effect beyond economic repair.
The fuse should simply be placed inside the holder and the screw cap replaced, when this is
done connect to the main power supply to check. If the unit is still not working then please contact
your dealer or CHAUVET for servicing.
Cleaning
The most important part of your lighting effect to keep clean is the lens as it allows the light output
to transmit. This should be cleaned with a soft damp cloth. The body of the unit may also be
cleaned in the same way. We recommend internal cleaning be carried out by a fully qualified
technician.
Maintenance & Servicing
Work on internal parts should be carried out by a qualified technician. Removal of covers other
than the front to replace lamp or effect dish, or the fuseholder is considered a breach of warranty
and will not be covered under any such agreement unless authorized first by the company.
Advertisement
