Wet Sounds HT-2 Owner's Manual
  1. Manuals
  2. Brands
  3. Wet Sounds Manuals
  4. Amplifier
  5. HT-2
  6. Owner's manual

Wet Sounds HT-2 Owner's Manual

600 watt 2 channel class d amplifier
Hide thumbs Also See for HT-2:

Advertisement

Table of Contents

HT-2
600 Watt 2 Channel
Class D amplifier
OWNER'S MANUAL
---------------------------------------------------------------------------------------------Wet Sounds HT-2 Owner's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HT-2 and is the answer not in the manual?

Questions and answers

Related Manuals for Wet Sounds HT-2

Summary of Contents for Wet Sounds HT-2

  • Page 1 HT-2 600 Watt 2 Channel Class D amplifier OWNER’S MANUAL ---------------------------------------------------------------------------------------------Wet Sounds HT-2 Owner’s Manual...

  • Page 2: Installation Instructions

    Thank you for purchasing the Wet Sounds Hydro-Tech series amplifier. Wet Sounds represents the ultimate in high performance Marine Audio. Wet Sounds™ Hydro-Tech™ Series Marine Amplifiers are designed to be a complete solution for every type of extreme marine application. The Hydro-Tech amplifiers use superior performance circuitry by utilizing Class D Power Supplies.

  • Page 3: Amplifier Connections

    The HT-2 is designed for 4 AWG Power wire (+12 V) and Ground wire (GND). You will need to Power Connections prepare the wire by remove 5/8”...
  • Page 4 The HT-2 has both extended RCA inputs and outputs. (see below) Connect the RCA outputs from Amplifier Signal Inputs/Outputs the source unit into the inputs of the amplifier. The HT-2 has 1 pair of inputs and is equipped with 1 pair of pass-through RCA outputs to connect to another amplifier...
  • Page 5 The HT-2 utilizes removable speaker terminal blocks for easier installations and stronger power Speaker Terminal Inputs connections. The terminal blocks are designed to accept 12 AWG- 16 AWG speaker wire. When preparing the wire you will need to strip 5/8” of the cables protective shielding. Then take a small flat head screwdriver and back out the screw on the terminal block.
  • Page 6 4. Variable Crossover 1-2 – Built in 12db filter with crossover frequencies between 50Hz – 250Hz. 5. Bass Boost Control 1-2 – This is a variable boost for the low frequencies to which the amplifier is set at on the crossover. ---------------------------------------------------------------------------------------------Wet Sounds HT-2 Owner’s Manual...
  • Page 7 5. Ground—Connect this terminal directly back to the battery, using the shortest wire necessary to make this connection. Always use wire of the same gauge or larger than the (+) 12 volt power wire. ---------------------------------------------------------------------------------------------Wet Sounds HT-2 Owner’s Manual...

  • Page 8: Setting Up The Amplifier

    Setting up the Amplifier Because of the wide range of head unit/radio output configurations all Wet Sounds amplifiers have Input Selection an adjustable input sensitivity or “GAIN”. The gain is NOT a volume or a power limiting control similar to a throttle. It makes the amplifier more sensitive to input from the stereo. When the gain is turned up the amplifier will reach full output at lower volume levels on the head unit/radio.

  • Page 9: Troubleshooting

    B. Confirm that there are no loose wires that could be grounding out the amplifier. C. Check that the amplifier has sufficient air circulation where it is located. Insufficient air flow and overdriving the audio system could result in the amplifier going into protection to preserve the amplifier. ---------------------------------------------------------------------------------------------Wet Sounds HT-2 Owner’s Manual...
  • Page 10 Sample System Setups ---------------------------------------------------------------------------------------------Wet Sounds HT-2 Owner’s Manual...
  • Page 11 ---------------------------------------------------------------------------------------------Wet Sounds HT-2 Owner’s Manual...

  • Page 12: Specifications

    Specifications ---------------------------------------------------------------------------------------------Wet Sounds HT-2 Owner’s Manual...
  • Page 13 >95dBa >95dBa >95dBa Noise Ratio Idle Current 2.5 A 1.7A 1.4A 1.6A Rating Max Current Rating Crossover Switchable Switchable Switchable Low Pass Type Hi/Lo/Full Hi/Lo/Full Hi/Lo/Full Turn on Delay Operating 10V-16V 10V-16V 10V-16V 10V-16V Voltage ---------------------------------------------------------------------------------------------Wet Sounds HT-2 Owner’s Manual...

  • Page 14: Limited Warranty

    Limited Warranty Length and limits of Warranty Wet Sounds warrants this product to be free of defects in material or workmanship for (1) year from the date of purchase. Wet Sounds warranty applies exclusively to the original purchaser, not transferable and the amplifier must be purchased from an Authorized Wet Sounds Retailer within the United States.

This manual is also suitable for:

Ht-4

Table of Contents