IBM SureMark 4610 1NF Hardware Service Manual
  1. Manuals
  2. Brands
  3. IBM Manuals
  4. Printer
  5. SureMark 4610 1NF
  6. Hardware service manual

IBM SureMark 4610 1NF Hardware Service Manual

Fiscal and fiscal ready point-of-sale (pos) printers
Hide thumbs
Table of Contents

Advertisement

Quick Links

SureMark 4610 Printers
Hardware Service Guide - Model 1NF
G362-0578-00

Advertisement

Table of Contents
loading

Related Manuals for IBM SureMark 4610 1NF

Summary of Contents for IBM SureMark 4610 1NF

  • Page 1 SureMark 4610 Printers Hardware Service Guide - Model 1NF G362-0578-00...
  • Page 3 SureMark 4610 Printers Hardware Service Guide - Model 1NF G362-0578-00...
  • Page 4 October 2011 This edition applies to IBM SureMark Printer Model 1NF single-station printer. The latest version of this publication is available from the IBM Web site. Complete the following steps to display a list of publications for your printer: 1. From http://www.ibm.com, click Support & downloads.

  • Page 5: Table Of Contents

    Removing the fiscal tray ..... 28 Installing the fiscal tray ..... . 29 © Copyright IBM Corp. 2010...
  • Page 6 Removing the fiscal logic card ....31 Installing the fiscal logic card ....34 Removing the electronic journal slot .
  • Page 7 Avis de conformité aux normes d'Industrie Canada ..87 Germany ......87 Australia and New Zealand .
  • Page 8 SureMark Hardware Service...

  • Page 9: Safety Information

    Safety information Danger: Before you begin to install this product, read the safety information in IBM Safety Information — Read This First, GA27-4004. This booklet describes safe procedures for cabling and plugging in electrical equipment. Gevaar: Voordat u begint met de installatie van dit produkt, moet u eerst de veiligheidsinstructies lezen in de brochure Veiligheidsinstructies—Lees dit eerst, GA27-4004.
  • Page 10 Voordat u begint met het installeren van dit produkt, dient u eerst de veiligheidsrichtlijnen te lezen die zijn vermeld in de publikatie IBM Safety Information — Read This First, GA27-4004. In dit boekje vindt u veilige procedures voor het aansluiten van elektrische appratuur.
  • Page 11 Vigyázat Mielôtt megkezdi a berendezés üzembe helyezését, olvassa el a IBM Safety Information — Read This First, GA27-4004 könyvecskében leírt biztonsági információkat. Ez a könyv leírja, milyen biztonsági intézkedéseket kell megtenni az elektromos berendezés huzalozásakor illetve csatlakoztatásakor. Pericolo prima di iniziare l'installazione di questo prodotto, leggere le informazioni relative alla sicurezza riportate nell'opuscolo Informazioni di sicurezza—Prime informazioni da leggere in cui sono descritte...
  • Page 12 Peligro Antes de empezar a instalar este producto, lea la información de seguridad en Información de Seguridad—Lea Esto Primero, GA27-4004. Este documento describe los procedimientos de sequridad para cablear y enchufar equipos eléctricos. Varning—livsfara Innan du börjar installera den här produkten bör du läsa säkerhetsinformationen i dikumentet Säkerhetsföreskrifter—Läs detta först, GA27-4004.
  • Page 13 GA27-4004 GA27-4004 Safety information...
  • Page 14 GA27-4004 GA27-4004 GA27-4004 GA27-4004 GA27-4004 GA27-4004 SureMark Hardware Service...

  • Page 15: Chapter 1. Introduction

    The softcopy version of this guide and other related publications are accessibility enabled. Who should read this guide This guide is intended for use by personnel who are installing and using the IBM SureMark 4610 Model 1NF single-station printer. How this guide is organized This publication is organized as follows: v Chapter 1, “Introduction”...

  • Page 16: Notices And Statements Used In This Book

    IBM SurePOS 500 Series: System Reference, SA27-4255. v POSS Programming Reference and User's Guide, SC30-3560 The latest version of this publication is available from the IBM Web site. Complete the following steps to display a list of publications for your printer: 1.

  • Page 17: Printer Information Label

    Printer information label The printer information labels A (Figure 1) are located beside the power button on the inside of the printer and the on the front right edge of the main cover. Note: You can find the fiscal serial number and other country specific identification information on a label on the Fiscal logic assembly (see “fiscal label”...

  • Page 18: Fiscal Label

    fiscal label You can find the fiscal serial number and other country specific identification information on the fiscal label A (Figure 2) on the fiscal logic assembly. Figure 2. fiscal label SureMark Hardware Service...

  • Page 19: Models And Features

    Models and features The following information is a high-level summary of the features and specifications for the IBM SureMark 4610 Model 1NF printers. Depending on the model, some features might not be available, or some specifications might not apply. Table 1. Feature and specifications...

  • Page 20: Warranty Information

    IBM fiscal logic assembly The IBM fiscal logic assembly consists of a tray, optional keylock, covers, fiscal fiscal screw, connectors, and ports. This section provides an illustration and text describing the parts of the IBM fiscal logic assembly. SureMark Hardware Service...
  • Page 21 Figure 3. IBM Fiscal Logic Assembly with USB and RS-232 communications options Fiscal screw The fiscal screw A (Figure 3) is a fiscal security device, used to secure the fiscal assembly in the printer. The screw is sealed using the required country specific fiscal seal. The 4610-NF can accommodate wire, wax, or lead seals.

  • Page 22: Power

    The power-cord and brick are used to supply power to the printer when: v The printer is connected to the system using the RS-232 connector. v The printer is connected to a standard USB port (for example, on a non-IBM Point of Sale system.) . Locating the power reset switch The power reset switch A (Figure 4 on page 9) for the 4610 Model 1NF single-station printer is located under the paper door.

  • Page 23: Operating System Requirements

    Figure 4. Power reset switch location Operating system requirements You can download drivers from the Retail Store Solutions Web site: http://www.ibm.com/solutions/retail/store/support/ RS-232 interface The RS-232 interface is supported on systems with the following operating systems: v Windows (POSReady; XP) UPOS 1.13 –...

  • Page 24: Usb Interface

    PC or other store controller with an RS-232 or USB port v SurePOS 700 Series systems v SurePOS 500 Series systems v SurePOS 300 Series systems v SurePOS 100 Series systems v IBM Self Checkout solution SureMark Hardware Service...

  • Page 25: Chapter 2. Product Specifications

    196 mm (7.72 in) 177 mm 145 mm (6.97 in) (5.71 in) Figure 5. IBM SureMark 4610 Model 1NF dimensions Table 4. Summary of dimensions Width: 145 mm (5.71 in) footprint Height: Cover closed: 196 mm (7.72 in) Cover open: 297 mm (11.69 in) Depth: 177 mm (6.97 in)

  • Page 26: Temperature And Humidity Limits

    Temperature and humidity limits Shipping -40° to 60° C (-40° to 140° F) with 5% to 100% relative humidity including condensation, but excluding rain Storage 0° to 60° C (32° to 140° F) with 5% to 80% relative humidity Operating 5°...

  • Page 27: Host And Audit Ports)

    Table 7. Powered USB 2 X 4 connector pin assignments (continued) Signal Ground (Frame) Ground (Frame) Ground (Frame) RS-232 (host and audit ports) Table 8. RS-232 pin assignments Signal Chapter 2. Product specifications...

  • Page 28: Cash Drawer

    Cash drawer A single connector can drive either a single cash drawer or two cash drawers using a special cable. The connector provides a status line if one of the cash drawers is open. The cash drawer cannot be activated while the printer is operating.

  • Page 29: Bar Codes

    <LpA>>m The mean value of the A-weighted sound pressure levels at the one-meter (bystander) positions for a random sample of machines. Indicates not applicable. All measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296. Bar codes SureMark printers can generate these bar codes: v UPC A/E...
  • Page 30 SureMark Hardware Service...

  • Page 31: Chapter 3. Adjusting And Maintaining The Suremark 4610 Model 1Nf Printers

    The paper feed motor must then catch up before the printer can feed the paper, which causes missing lines or partial lines of print. Use the customer receipt feed button to advance the receipt and all lines will print. © Copyright IBM Corp. 2010...
  • Page 32 IBM specifications might result in a billable service call, regardless of the existence of a service contract. A list of supported paper and suppliers are available from the IBM Web site. To check for updated printer paper information, complete the following steps.

  • Page 33: Cleaning Recommendations

    Cleaning recommendations You should inspect your 4610 unit periodically and clean the cover as required. Use a soft, clean cloth with warm, soapy water to clean the plastic parts. Do not use abrasives or any alkaline, ammonia, or chloride-based cleaner. Note: Do not apply cleaning solution directly to the cover.
  • Page 34 SureMark Hardware Service...

  • Page 35: Chapter 4. Running Tests And Diagnostics

    Chapter 4. Running tests and diagnostics This chapter describes the IBM Diagnostics for POS Systems and Peripherals, off-line tests, and troubleshooting procedures. Testing the printer The SureMark single station fiscal printer consists of a Suremark printer integrated with a fiscal logic card.

  • Page 36: Troubleshooting

    Troubleshooting Table 12 contains common steps to identify and resolve problems. For the latest troubleshooting guidance and symptom-fix tip information, go to the IBM Knowledgebase support Web site: http://www2.clearlake.ibm.com/store/support/html/knowledgebase.html This site contains additional information that is gathered from field experience, and might not have been available at the publishing date of this document.

  • Page 37: Firmware Off-Line Tests

    2. Record all symptoms before calling for service. 3. If you receive software error messages, refer to the software manual of the application. 4. The IBM 4610 SureMark Fiscal printer returns codes specific to your country. 5. Call your service representative.
  • Page 38 Figure 6. Off-line tests activation 3. Close the paper door cover. 4. Press and hold the paper feed button until you hear a click and the front LED indicator blinks. Upon entering the off-line test mode the following off-line selection menu is printed. Follow the instructions on the printed menu.

  • Page 39: Low Paper Sensing And Calibration

    Summary of off-line test menus The following table describes the off-line test menu and sub-menu items. Table 13. Summary of the off-line test menu items Submenu (if Menu item Definition applicable) Definition Thermal Receipt test Prints a receipt Fiscal offline test Fiscal test Varies by country.
  • Page 40 Table 14. MCT load command settings for low-paper and critically low-paper amounts (continued) Constant Decimal Hexadecimal Description Critically low-paper amount X'27' The amount of paper remaining in the printer when it sends the critically low-paper status. Default is 1 meter (1000 or 0X'03E8'; number is stored as mm).

  • Page 41: Chapter 5. Removing And Replacing Frus

    Do not place the device onto the cover of the system or onto a metal table. v Take additional care when handling devices during cold weather because heating reduces indoor humidity and increases static electricity. © Copyright IBM Corp. 2010...

  • Page 42: Removing The Fiscal Tray

    This section provides information for removing an IBM fiscal tray from a fiscal printer. For information on how to remove a fiscal tray from a fiscal ready printer with an IBM business partners fiscal solution installed, see the documentation provided by the IBM business partner.

  • Page 43: Installing The Fiscal Tray

    This section provides information for installing and IBM fiscal tray in the printer. For information on how to install a fiscal tray in a fiscal ready printer with an IBM business partners fiscal solution installed, see the documentation provided by the IBM business partner.
  • Page 44 Removing and replacing FRUs 4. Use the fiscal screw to secure the fiscal tray; then, install the seal. Important: The methods of installing the seal as well as the type of seal used is country specific. See the information provided by the fiscal authority in your country for details about the type of seal and how to install it.

  • Page 45: Removing The Fiscal Logic Card

    IBM. If your fiscal solution is provided by an IBM business partner, see the documentation provided by the IBM business partner for more information. The fiscal logic card is the logic card installed in the fiscal logic tray and should not be confused with the logic card that is installed on the printer unit under the main cover.
  • Page 46 Removing and replacing FRUs Figure 9. Removing the fiscal tray cover. 3. Remove the screws A (Figure 9) that secure the cover; then, remove the cover B (Figure 9) from the tray by lifting it straight up and off the tray. The fiscal memory is epoxied to the inside of the cover and also connects to the fiscal logic card.
  • Page 47 Removing and replacing FRUs Figure 10. Remove the fiscal card 4. Remove the electronic journal slot D and slot assembly C (see “Removing the electronic journal slot” on page 37 and “Removing the electronic journal slot assembly” on page 37 for information). Chapter 5.

  • Page 48: Installing The Fiscal Logic Card

    This section provides the information needed to install the fiscal logic card A (Figure 11) in the fiscal tray provided by IBM. If your fiscal solution is provided by an IBM business partner, see the documentation provided by the IBM business partner for information.
  • Page 49 Removing and replacing FRUs 2. Open the static-protective package and grasp the card by the edges and remove it from the package. Set the card down on the static-protective package. 3. Remove the hex nuts from the RS-232 connectors and set them aside for future use. 4.
  • Page 50 Removing and replacing FRUs 16. Install the electronic journal card into the electronic journal slot. If the card does not go into the slot, do not force it. Ensure the electronic journal card is right side up and attempt to insert it in the slot again.

  • Page 51: Removing The Electronic Journal Slot

    Removing and replacing FRUs Removing the electronic journal slot This section provides information needed for removing the electronic journal slot assembly and the electronic journal slot card. It is not necessary to remove the fiscal logic card from the tray to remove or install the electronic journal slot card.

  • Page 52: Removing The Electronic Journal Slot Card

    Removing and replacing FRUs Removing the electronic journal slot card Figure 14. Remove the electronic journal slot card The fiscal logic card does not have to be removed from the tray to remove the electronic journal slot card from its mount on the logic card. To remove the electronic journal slot card, complete the following steps: 1.

  • Page 53: Installing The Electronic Journal Slot Assembly

    Removing and replacing FRUs Installing the electronic journal slot assembly To install the electronic journal slot assembly, complete the following steps (see Figure 13 on page 37 for additional information): 1. Ensure the I/O probe shield is in place. If not, install the shield before continuing. To install the shield: a.

  • Page 54: Removing The Program Memory Assembly

    Removing and replacing FRUs Removing the program memory assembly This section provides the information needed to remove the program memory from the fiscal logic card. Figure 16. Install the program memory To remove the program memory, complete the following steps: 1.

  • Page 55: Installing The Program Memory Assembly

    Removing and replacing FRUs Installing the program memory assembly This section provides the information needed to install the program memory on the fiscal logic card. Refer to Figure 16 on page 40. To install the program memory, complete the following steps: 1.

  • Page 56: Installing The Paper Door Cover

    Removing and replacing FRUs 2. Grasp both sides of the paper door cover and use your thumbs to press outward on the cover retention tabs A as shown in Figure 18. Figure 18. Removing the paper door cover 3. While grasping the paper door cover and holding the retention tabs outward, slide the paper door cover toward the front of the printer until it stops;...
  • Page 57 Removing and replacing FRUs Figure 19. Installing the paper door cover To install the paper door cover A (Figure 19), complete the following steps: 1. Open the paper door and orientate printer so the customer receipt feed button C (Figure 19) is on the right side of the printer.

  • Page 58: Removing The Main Cover

    Removing and replacing FRUs Removing the main cover This section provides information for removing the main cover from a fiscal printer. Note: The following figure shows the location of the main cover release tab if you turn the printer over. During the removal process, the printer must be placed upright and you will have to locate the tab by feel.
  • Page 59 Removing and replacing FRUs 3. If necessary, remove the fiscal tray from the printer (see “Removing the fiscal tray” on page 28 for information). 4. Remove the fiscal security bar ( A in Figure 21): Figure 21. Removing the security bar a.

  • Page 60: Installing The Main Cover

    Removing and replacing FRUs 11. Press the release tab toward the front of the printer, while pushing the rear of the cover up with your thumb and lifting slightly on the front. As the cover is released and begins to move upward, remove your hand from under the printer and lift the cover up and off.

  • Page 61: Removing The Fiscal Base

    Removing and replacing FRUs Removing the fiscal base This section provided information on how to remove the fiscal base from a fiscal printer. For information on how to remove the fiscal base from a fiscal ready printer (see “Fiscal base” on page 69 in Appendix A, “1NF fiscal ready printer,”...

  • Page 62: Installing The Fiscal Base

    Removing and replacing FRUs b. Locate the connector and push in on the two release tabs on either side of the connector while pushing it up and out of the mount. Figure 23. Remove the bottom fiscal base from the printer. 5.

  • Page 63: Removing The Paper Motion Sensor

    Removing and replacing FRUs 4. Install the ground plane: a. Insert the tab on the left rear corner of the ground plane into the slot in the left corner of the printer. b. Rotate the right side of the ground plane into place while guiding the tab on the right rear corner into its mounting slot on the right rear corner.

  • Page 64: Installing The Paper Motion Sensor

    Removing and replacing FRUs 3. Pull gently on the top of the paper motion sensor B (Figure 24) to pivot it open. Figure 24. Paper motion sensor 4. Disconnect the cable that connects the paper motion sensor to the logic card. 5.

  • Page 65: Removing The Thermal Printhead

    Removing and replacing FRUs Removing the thermal printhead This section provides the information needed to remove the thermal printhead from a fiscal or fiscal ready printer. To remove the thermal printhead, complete the following steps: 1. Remove the logic card (see “Removing the logic card” on page 54 for information on how to remove the logic card).

  • Page 66: Installing The Thermal Printhead

    Removing and replacing FRUs 5. While supporting the printhead with one hand use a screwdriver with a magnetic-head to remove the mounting screws A (Figure 26); then, lift the printhead partially out of the printer. Screws Figure 26. Paper door release lever 6.

  • Page 67: Removing The Thermal Printhead Flat Cable

    Removing and replacing FRUs Removing the thermal printhead flat cable This section provides the information needed to remove the thermal printhead flat cable from a fiscal or fiscal ready printer. xxxxx Figure 27. Removing and installing the thermal printhead flat cable. To remove the thermal printhead flat cable A (Figure 27), complete the following steps: 1.

  • Page 68: Removing The Logic Card

    Removing and replacing FRUs 4. An improperly installed cable will result in no communication between the logic card and the thermal print head. To install the thermal printhead flat cable, complete the following step: 1. Orient the cable so the longest end is facing up and the blue stripe facing away from you. 2.
  • Page 69 Removing and replacing FRUs Figure 28. Removing the interface card 5. Position the printer on a work surface with the logic card B (Figure 29 on page 56) facing you; then, press upward on the logic card B (Figure 29 on page 56) release tab and rotate the top of the logic card away from the printer unit.

  • Page 70: Installing The Logic Card

    Removing and replacing FRUs Figure 29. Removing the logic card 6. Note the position of the cables connected to the logic card; then, disconnect them. 7. The logic card can now be set aside in a static-protective package. Note: If the logic card is to be reinstalled, take precautions to avoid damage from static electricity. For details about handling these devices, see “Handling static-sensitive devices”...
  • Page 71 Removing and replacing FRUs Figure 30. Logic card Attention: When you handle static-sensitive devices, take precautions to avoid damage from static electricity. For details about handling these devices, see “Handling static-sensitive devices” on page 27. To install the logic card, complete the following steps: 1.

  • Page 72: Removing The Cutter Motor And Paper Door Assembly

    Removing and replacing FRUs c. Rotate the interface card toward the printer until is clicks into place. 7. Turn the printer over and install the flex cable connector onto the logic cards connector. Note: Ensure that the ground strap ( A in Figure 31) makes contact with the tab ( B in Figure 31) on the logic card.
  • Page 73 Removing and replacing FRUs Figure 32. Cutter motor screws 5. Remove the paper door assembly: a. Remove the long leg of the lift spring ( B in Figure 33 on page 60) from the mounting slot. b. Rotate the spring until short leg of the spring is no longer in contact with the paper door; then, remove the spring from the post.

  • Page 74: Installing The Cutter Motor And Paper Door Assembly

    Removing and replacing FRUs Figure 33. Clearing the drag strip detent c. Repeat steps 5a on page 59 and 5b on page 59 to remove the second spring; then continue on to the next step. d. Lift the tip of the drag strip ( A in Figure 33) while opening the paper door assembly further, so that the tab at the end of the drag strip clears its detent.
  • Page 75 Removing and replacing FRUs d. Align the end of the spring leg with the slot and hole in the paper door assembly; then, rotate the bottom of the spring toward the front of the printer unit and insert the hooked end into the mounting slot.

  • Page 76: Removing The Rollers

    Removing and replacing FRUs Removing the rollers This section provides the information needed to remove the rollers from a fiscal or fiscal ready printer. To remove the rollers, complete the following steps: Note: Only use this procedure if you are replacing all rollers. If you are replacing only the lower four rollers, you only need to open the paper door cover and proceed to Step 4.

  • Page 77: Installing The Rollers

    Removing and replacing FRUs Installing the rollers This section provides the information needed to install all the rollers in a fiscal or fiscal ready printer. If you are installing only the bottom four rollers begin at step 2. Figure 35. Place Holder for Future Artwork To install the rollers, complete the following steps: 1.

  • Page 78: Removing The Low-Paper Sensor

    Removing and replacing FRUs Removing the low-paper sensor This section provides the information needed to remove the low-paper sensor from a fiscal or fiscal ready printer. To remove the low-paper sensor, complete the following steps: Note: Do not disconnect any cables other than the three wire low-paper sensor cable from the logic card. 1.

  • Page 79: Installing The Low-Paper Sensor

    Removing and replacing FRUs Installing the low-paper sensor This section provides the information needed to install the low-paper sensor in a fiscal or fiscal ready printer. Figure 37. Installing the low-paper sensor. To install the low-paper sensor, complete the following steps: 1.

  • Page 80: Removing The Paper Transport Frame From The Main Frame

    Removing and replacing FRUs Removing the paper transport frame from the main frame This section provides the information to remove the paper transport frame from the printers main frame of a fiscal or fiscal ready printer. To remove the paper transport frame from the main frame, complete the following steps: 1.

  • Page 81: Installing The Paper Transport Frame On The Main Frame

    Removing and replacing FRUs Installing the paper transport frame on the main frame This section provides the information needed to install the paper transport frame on to the printers main frame of a fiscal or fiscal ready printer. To install the paper transport frame on the main frame, complete the following steps: 1.
  • Page 82 SureMark Hardware Service...

  • Page 83: Appendix A. 1Nf Fiscal Ready Printer

    Appendix A. 1NF fiscal ready printer This section contains information on the IBM SureMark 4610 Model 1NF point-of-sale fiscal ready printer. The IBM SureMark 4610 Model 1NF point-of-sale fiscal ready printer is a high-performance printer is based on IBM 4610 technologies, incorporating a fiscal ready solution developed by IBM business partners world wide having features and components that differ from the 4610 Model 1NF point-of-sale fiscal printer.
  • Page 84 Figure 39. Removing the security bar 2. Remove the top and main cover ( see “Removing the paper door cover” on page 41 and “Removing the main cover” on page 44 for information). 3. Remove the two screws securing the ground plate in place; then, remove the ground plate from the printer and place the ground plate and the screws in a safe location for future use.
  • Page 85 Figure 40. Remove ground plate 4. Remove the two screws securing the fiscal base to the printer: a. Position the printer upright on a work surface with the front of the printer facing you. b. Remove the two mounting screws from either side and place them in a safe place for future use. Appendix A.

  • Page 86: Installing The Fiscal Base On A Fiscal Ready Printer

    Figure 41. fiscal base removal 5. Remove the fiscal base from the bottom of the printer. Installing the fiscal base on a fiscal ready printer To install the fiscal base on a fiscal ready printer, complete the following steps: 1. Place the main frame of the printer on to the fiscal base. 2.

  • Page 87: Interface Card

    8. Turn the printer over and install the paper door cover (see “Installing the paper door cover” on page 42 for information). Interface card This section provides information on the connectors, installation and removal of the interface card installed in the 1NF fiscal ready printer Connectors Figure 42.

  • Page 88: Installing The Interface Card

    Figure 43. Removing the interface card Installing the interface card Note: You might prefer to plug all cables into the interface card before installation; however, do not plug in any power until after installation. To install the interface card, complete the following steps: SureMark Hardware Service...
  • Page 89 Figure 44. Installing the interface card 1. Place the printer unit upside down on a flat work surface. 2. Insert the tab of the interface card into the slot on the base of the printer. 3. Press down on the side of the interface card opposite the tab until the blue release button slider snaps into place.
  • Page 90 SureMark Hardware Service...

  • Page 91: Appendix B. Country Specific Information

    Table 15. Electronic Journal Security and Sealing Information Country Electronic Journal Access Fiscal Screw Fiscal Seal Turkey Keylock M4 X 16 Lead Seal Italy Keylock M4 X 16 Wax Seal Greece Keylock M4 X 20 Wax Seal Hungary Keylock Chile Venezuela © Copyright IBM Corp. 2010...
  • Page 92 SureMark Hardware Service...

  • Page 93: Appendix C. Parts Listing

    Detail parts of a main assembly One Dot Subassembly of the main assembly Two dots Detail part of a one-dot subassembly Two dots Subassembly of a one-dot subassembly Three dots Detail part of a two-dot subassembly © Copyright IBM Corp. 2010...

  • Page 94: Assembly 1: Model 1Nf

    Assembly 1: Model 1NF SureMark Hardware Service...
  • Page 95 Assembly 1: (continued) Asm– Part Index Number Units Description 1– 73Y1158 1 Model 1NR, 80 mm pearl white covers without interface card – 73Y1159 1 Model 1NR, 80 mm, iron gray covers, without interface card – 84Y0539 Model 1NR, fiscal ready,80 mm pearl white covers without fiscal drawer assembly –...

  • Page 96: Assembly 2: Model 1Nf, Fiscal Drawer Assembly

    Assembly 2: Model 1NF, Fiscal drawer assembly SureMark Hardware Service...

  • Page 97: Power Cords

    1 Fiscal electronic journal SD card (not shown) Power cords For your safety, IBM provides a power cord with a grounded attachment plug to use with this IBM product. To avoid electrical shock, always use the power cord and plug with a properly grounded outlet.

  • Page 98: Cables

    Table 16. Power cord part numbers (continued) IBM power cord part number Used in these countries and regions 39M5079 Bahamas, Barbados, Bermuda, Bolivia, Canada, Cayman Islands, Columbia, Costa Rica, Dominican Rep., El Salvador, Ecuador, Guatemala, Haiti, Honduras, Jamaica, Mexico, Netherlands Antilles,...

  • Page 99: Appendix D. Notices

    IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property right may be used instead.

  • Page 100: Electronic Emission Notices

    Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.

  • Page 101: Industry Canada Class A Emission Compliance Statement

    In solch einem Fall ist der Abstand bzw. die Abschirmung zu der industriellen Störquelle zu vergröβern." Anmerkung: Um die Einhaltung des EMVG sicherzustellen sind die Geräte, wie in den IBM Handbüchern angegeben, zu installieren und zu betreiben. Australia and New Zealand Attention: This is a Class A product.

  • Page 102: Chinese Class A Warning Statement

    Chinese Class A warning statement Attention: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Japanese power line harmonics compliance statement Japanese Voluntary Control Council for Interference (VCCI) statement Attention: This product is a Class A Information Technology Equipment and conforms to the standards...

  • Page 103: Taiwanese Class A Warning Statement

    Taiwanese Class A warning statement Taiwan contact information IBM Taiwan Product Service Contact Info: IBM Taiwan Corporation 3F, No 7, Song Ren Road, Taipei Taiwan Telephone: 0800-016-888 Cable ferrite requirement All cable ferrites are required to suppress radiated EMI emissions and must not be removed.

  • Page 104: Product Recycling And Disposal

    (IT) equipment to responsibly recycle their equipment when it is no longer needed. IBM offers a variety of product return programs and services in several countries to assist equipment owners in recycling their IT products. Information on IBM product recycling offerings can be found on IBM’s Internet site at http://www.ibm.com/ibm/environment/products/prp.shtml.

  • Page 105: Battery Return Program

    In the United States, IBM has established a return process for reuse, recycling, or proper disposal of used IBM sealed lead acid, nickel cadmium, nickel metal hydride, and other battery packs from IBM equipment.

  • Page 106: For California

    For proper collection and treatment, contact your local IBM representative. This notice is provided in accordance with Royal Decree 106/2008 of Spain: The retail price of batteries, accumulators and power cells includes the cost of the environmental management of their waste.

  • Page 107: Trademarks

    Trademarks The following are trademarks of International Business Machines Corporation in the United States or other countries, or both: AnyPlace Kiosk(tm) AnyPlace POS Hub(tm) DB2 Universal Database IBM and the IBM logo PS/2 SureMark SurePoint SurePOS Wake on LAN WebSphere Microsoft, Windows, Windows NT, and the Windows logo are trademarks of Microsoft Corporation in the United States, other countries, or both.
  • Page 108 SureMark Hardware Service...

  • Page 109: Index

    6 humidity requirements 12 RS-232 interface card 73 connector pin assignments 12 connectors and ports IBM Fiscal Logic Assembly 7 install 12 V USB display port 7 cutter motor 60 24 V USB communications port 7 electronic journal slot 38...
  • Page 110 89 Fiscal Logic Assembly electronic emissions 86 SC card slot 7 electrostatic discharge (ESD) 89 IBM Fiscal Ready Logic Assembly end of life disposal 90 SC card slot 7 IBM 85 speed, printing 14 static-sensitive devices, handling 27...

  • Page 111: Part Number Index

    2– 50Y0094 1– 84Y0527 1–2 50Y0096 1– 84Y0528 1–2 60Y3083 1–8 84Y0539 1– 60Y3153 1–11 84Y0540 1– 60Y3155 1–11 84Y0587 2–4 60Y3165 1–9 84Y0596 2–3 60Y3168 1– 93F0415 1– 60Y3172 1–9 98Y4856 2–5 73Y1111 2–1 © Copyright IBM Corp. 2010...
  • Page 112 G362-0578-00...

Table of Contents