Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Lawn Sweeper
  5. 326SX-SERIES
  6. Operator's manual

Husqvarna 326SX-SERIES Operator's Manual

Carb ii, epa ii
Hide thumbs

Advertisement

Quick Links

Download this manual See also: Operator's Manual
Table of Contents
Operator's manual (CARB II, EPA II)
326S
X-SERIES
Please read these instructions carefully and make
English
sure you understand them before using the machine.

Advertisement

loading

  Also See for Husqvarna 326SX-SERIES

Husqvarna 326SX-Series Operator's Manual
Husqvarna 326SX-Series Operator's Manual 24 pages

  Related Manuals for Husqvarna 326SX-SERIES

  Summary of Contents for Husqvarna 326SX-SERIES

  • Page 1 Operator's manual (CARB II, EPA II) 326S X-SERIES Please read these instructions carefully and make English sure you understand them before using the machine.

  • Page 2: Symbols

    SYMBOL EXPLANATION Symbols Checks and/or maintenance should be WARNING! Sweepers can be carried out with the engine switched off, dangerous! with the stop switch in the STOP Careless or incorrect use can result in position. serious or fatal injury to the operator or others.

  • Page 3: Table Of Contents

    CONTENTS Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and List of contents appearance of products without prior notice. SYMBOL EXPLANATION Maintenance, replacement, or repair of the emission control Symbols ................2 devices and systems may be performed by any nonroad engine repair establishment or individual.

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment The machine‘s safety equipment IMPORTANT INFORMATION This section describes the machine‘s safety equipment, its function and how checks and maintenance are carried out to • A sweeper used incorrectly or carelessly can ensure that it operates correctly. (See the chapter “What is become a dangerous tool, that can cause serious what“...
  • Page 5 SAFETY INSTRUCTIONS 3. Vibration 4. Muffler damping system The muffler is designed to give the lowest possible noise Your machine is equipped level and to direct the engine‘s with a vibration damping exhaust fumes away from the system, which is designed to operator.

  • Page 6: Control, Maintenance And Service Of The Machine's Safety Equipment

    SAFETY INSTRUCTIONS 3. Vibration Control, maintenance and service of damping system the machine‘s safety equipment • Check the vibration IMPORTANT INFORMATION damping element • All service and repairs to the machine require regularly for material special training. cracks and distortion. •...

  • Page 7: General Safety Instructions

    SAFETY INSTRUCTIONS General safety instructions Fuel safety • Always use a fuel container IMPORTANT INFORMATION with an anti-spill valve. • The machine is only designed for sweeping lawns, pathways, asphalt roads and the like. • Never fill the machine while the engine is running.

  • Page 8: General Working Instructions

    SAFETY INSTRUCTIONS Safety instructions before starting work 2. Avoid usage in unfavourable weather • Inspect the working area. Remove all loose objects, such as conditions. For example, stones, broken glass, nails, steel wire, twine and the like that thick fog, heavy rain, could be thrown outwards or become entangled in the strong winds or extreme sweeper.
  • Page 9 SAFETY INSTRUCTIONS • The sweeper works best when the rubber blades can quickly WARNING! When you turn the machine slide over or stroke the surface. New or replaced sweeper over, litter is thrown backwards towards the rollers tend to stick or drag on hard surfaces, and should user.

  • Page 10: What Is What

    WHAT IS WHAT? What is what on the sweeper? 1. Blade 12. Stop switch 2. Sweeper roller 13. Throttle trigger lock 3. Roller shaft 14. Cylinder cover 4. Pin 15. Starter handle 5. Hairpin spring 16. Fuel tank 6. Plastic sleeve 17.

  • Page 11: Assembly

    ASSEMBLY Assembling the loop handlebar Assembling the sweeper • Clip the loop handle onto 1. Slide the plastic sleeve (wear protection) (A) onto the shaft the tube. Note that the (B). loop handle must be fitted 2. Fit the gearbox (C) on the tube (B). Tighten clamp screw between the arrows on the (D) at the gearbox.

  • Page 12: Fuel Handling

    • Ensure that the fuel is well mixed by shaking the Two-stroke oil container before filling the • For the best results use tank. HUSQVARNA two-stroke Min. 3 m oil, which has been (10 ft) specially developed for clearing saws and chain saws.

  • Page 13: Start And Stop

    START AND STOP Start and stop Start Press the machine body against the ground using your WARNING! left hand (NOTE! Not your The complete clutch cover with shaft must foot). Grip the starter handle, be fitted before the machine is started, otherwise the clutch can become loose slowly pull out the cord with and cause personal injury.

  • Page 14: Maintenance

    MAINTENANCE Carburetor Basic setting Your Husqvarna product has been designed and manufactured • The carburetor is set to its basic setting when test run at the to specifications that reduce harmful emissions. factory. The basic setting should be kept during the After your unit has been run 8-10 tanks of fuel the engine has machine‘s first working hours.
  • Page 15 MAINTENANCE Final setting of the idling speed T Correctly adjusted carburetor Adjust the idling speed with A correctly adjusted carburetor means that the machine the screw T, if it is necessary accelerates without hesitation and the machine 4-cycles a little to readjust.

  • Page 16: Muffler

    MAINTENANCE Muffler Cooling system NOTE! To maintain as low operating Some mufflers are fitted with a catalytic converter. See temperature as possible the “Technical data” to see whether your machine is fitted with a engine is equipped with a catalytic converter. cooling system.

  • Page 17: Air Filter

    MAINTENANCE Air filter NOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does The air filter should be not cover damage or liability caused by the use of accessories...

  • Page 18: Technical Data

    TECHNICAL DATA Technical data 326S Engine Displacement, cu. in/cm 1,50/24,5 1,32/34 Cylinder bore, inch/mm Stroke length, inch/mm 1,06/27 Recommended max. speed, rpm 11 000 - 11 700 Idling speed, rpm 2 700 Speed of output shafts, rpm 0,9 kW/ 8400 rpm Max.

  • Page 19: Emission Control Warranty Statement

    Repair or replacement of any warranted part will be perfor- The EPA (U.S. Environmental Protection Agency), CARB med at no charge to the owner at an approved Husqvarna (California Air Resources Board), Environment Canada and Forest & Garden servicing dealer.
  • Page 20 114 01 18-93 ´+H+y¶3b¨ 2002W23...

This manual is also suitable for:

326sx series