Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for PYLE Audio PMX401
Summary of Contents for PYLE Audio PMX401
-
Page 1: Owners Manual
OWNERS MANUAL PMX401 4 CHANNELS PMX601 6 CHANNELS PMX802 8 CHANNELS www.pyleaudio.com... -
Page 2: Features At A Glance
FEATURES AT A GLANCE 4,6,8 Balanced microphone inputs, 4,6,8 high impedance microphone/line Inputs and Tape/CD inputs. All may be used simultaneously. Reverb built in with individual control on each channel line out for connection to external amplifiers. Record out jack for taping performances. R.F interference protection on all inputs and outputs. The powered mixer is not only easy to use and transport, but designed with the latest technology. -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS CAUTION: To reduce the risk of electrical shock, do not remove the cover (or back). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture. This symbol, wherever it appears, This symbol, wherever it appears, alerts you to the presence of... - Page 4 A. FRONT PANEL SECTION FEATURES 1. BALANCE INPUT (MIC) Electronic Balanced inputs acceptable a standard XLR male connector. It is designed to accept a...
- Page 5 balanced low impedance input signal, Phantom power (15 volts) for condenser microphones is always on and available. It has an input impedance of 1K ohm. The connector is wired as: Pin= shield ; Pin3= negative(cold). 2. BALANCE INPUT(LINE) ＂ Electronic Balanced inputs acceptable a standard 1/4 jacks connector.
-
Page 6: Graphic Equalizer
6. EFF This is a send control to the reverb buss, It controls the amount of reverberation added to the input Signals. 7. GRAPHIC EQUALIZER 2×5-band equalizer is provided for tone control over each frequency , and for precise high quality sound by final tone control. - Page 7 12. PHANTOM LED The LED +15V will be turned on when start working. 13. PHANTOM POWER SWITCH When it is depressed, the XLR jack input has +15V voltage. 14.EFF DELAY Using by this control, you can adjust the delay time interval of echo repeat. 15.
-
Page 8: Tape Input
This controls the level of the playback inputs(RCA) jack. 19.TAPE INPUT These RCA jacks are for brining in a tape deck, CD play or other line level source. The impedance Is 10k ohms . 20. REC OUTPUT These RCA jacks are for hooking up a tape desk to record from the mixer. Both channel are summed into mono for compatibility. - Page 9 1. SPEAKER JACK (LEFT/RIGHT) These are 2 conductor 1/4” speaker outputs. Each one is rated at 8 ohm minimum impedance. Total minimum load for the amplifier is 4 ohms. You may comment either 1-4 ohm. 1-8 ohm or 2-8 ohm speaker cabinets.
-
Page 10: Power Switch
＂ Using by this jack, you can use stereo 1/4 jacks connector send internal signal which before power amplifier to external effects processing, after processing return to internal power amplifier. ＂ Or you can use stereo or mono 1/4 jacks connector send external signal to inner power amplifier . 3. - Page 11 C.CONNECTIONS You will need a lot of cables for different purposes – see the following figures to make sure you have got the right ones. Unbalanced equipment may be connected to balanced inputs/outputs. Either use ＂ mono 1/4 jacks or connect ring and sleeve of TRS jacks.
-
Page 13: Speaker Connections
Speaker Connections VERY IMPORTANT, PLEASE READ BEFORE CONNECTING SPEAKERS. One or more speakers (2, 4, or 8 ohm) can be connected to the amplifier with or without transformers. However, before you connect any speaker to the amplifier, the total speaker impedance must be calculated in order to avoid damage to the amplifier. - Page 17 D.APPENDIX Bandwidth 20Hz to 20kHz_+ 1dB Input Impedance: Lo-Z Mic 1K ohms Hi-Z Mic/Line 33K ohms Tape playback 10K ohms Phone 51 ohms Input level: Lo-Z Mic -50dB Hi-Z Mic/Line -20dB Tape playback -10dB Bandwidth 20Hz to 20kHz_+ 1dB Rec output level +22dB(max) Phone output level +22dB(max)