Table of Contents
Advertisement
Quick Links
Installation and Operating Data
Installation and
Operation Manual
Stealth Series
Pumps
Models SHPF and SHPM
FOR YOUR SAFETY: This product must be in stalled and serviced by a professional service
technician, qualified in pool/spa installation. The procedures in this manual must be followed
exactly. Improper in stal la tion and/or op er a tion can create dangerous electrical hazards which
can cause high voltages to run through the electrical system, possibly causing death, serious
injury or property damage. Improper in stal la tion and/or op er a tion will void the warranty.
WARNING
ATTENTION INSTALLER: This manual contains important information about
the in stal la tion, operation and safe use of this product. This information
should be given to the owner/operator of this equipment.
Advertisement
Table of Contents
Related Manuals for Jandy SHPF
Summary of Contents for Jandy SHPF
- Page 1 Installation and Operation Manual Stealth Series Pumps Models SHPF and SHPM WARNING FOR YOUR SAFETY: This product must be in stalled and serviced by a professional service technician, qualified in pool/spa installation. The procedures in this manual must be followed exactly.
-
Page 3: Table Of Contents
3.2.1 Voltage Checks........ Replacement Parts List ....3.2.2 Bonding and Grounding ....Exploded View ........ 3.2.3 Electrical Wiring ......SHPF and SHPM Pump Curves ..Pressure Testing ......Physical and Operational Section 4. Operation .......... Specifi cations ........Start-up .......... -
Page 4: Section 1. Important Safety Instructions
® certified electrician or a qualified swimming pool service tech ni cian. WARNING Due to the potential risk of fire, electric shock, or injuries to persons, Jandy ® Pumps must be installed in accordance with the National Electric Code, all local electrical and safety codes, and the Occupational Safety and Health Act (OSHA). - Page 5 • Water temperature for test must NOT EXCEED 100°F (38°C). • Limit test to 24 hours. After test, visually check system to be sure it is ready for operation. • Notice: These parameters apply to Jandy equipment only. For non-Jandy equipment, consult ®...
-
Page 6: Pool Pump Suction Entrapment Prevention Guidelines
Page 6 Pool Pump Suction Entrapment Prevention Guidelines WARNING SUCTION HAZARD. Can cause serious injury or death. Do not use this pump for wading; shallow pools or spas containing bottom drains, unless pump is connected to at least two functioning suction outlets. WARNING Pump suction is hazardous and can trap and drown or disembowel bathers. - Page 7 Page 7 At Least 3 Feet Listed/certified to Listed/certified to ANSI/ASME A112.19.8 ANSI/ASME A112.19.8 Anti-entrapment Anti-entrapment Cover/Grate or Suction Cover/Grate or Suction Fitting, screw-fastened Fitting, screw-fastened No valves between to Main Drain Sump to Main Drain Sump Tee and Main Drains Suction Outlet Suction Outlet (Main Drain)
-
Page 8: Section 2. General Description
This manual contains information for the proper the water level of the pool. A check valve is installation, operation and maintenance of Jandy ® recommended on the suction line to the pump. -
Page 9: Pipe Sizing
(GPM) Always use properly sized valves. Jandy ® may not be delivered and the pump will make noise and shorten pump life. (cavitate) -
Page 10: Electrical Installation
BRANCH FUSE AMPS 0-50 FEET 50-100 FEET 100-150 FEET 150-200 FEET Model 208-230 VAC 115 VAC 208-230 VAC 115 VAC 208-230 VAC 115 VAC 208-230 VAC 115 VAC SHPF.75HP/SHPM1.0HP SHPF1.0HP/SHPM1.5HP SHPF1.5HP/SHPM2.0HP SHPF2.0HP/SHPM2.5HP SHPF3.0HP SHPM2.0HP-2-SPEED (1) SHPM2.5HP-2-SPEED (1) *ASSUMES THREE COPPER CONDUCTORS IN A BURIED CONDUIT AND 3% MAXIMUM VOLTAGE LOSS IN BRANCH CIRCUIT. ALL NEC AND LOCAL CODES MUST BE FOLLOWED. -
Page 11: Pressure Testing
Page 11 Pressure Testing Release all pressure from the system and open the filter pressure release valve. WARNING If the pump is located below the water level of When pressure testing a system with water, air is often the pool, opening the filter pressure release valve trapped in the system during the filling process. -
Page 12: Section 5. Service And Maintenance
Page 12 Section 5. Service and Maintenance Turn on the power to the pump. Once all the air has been evacuated from the filter, close the pressure release valve. Routine Maintenance The pump will collect any large debris present in Winterizing the Pump the water at the pump basket. -
Page 13: Section 6. Troubleshooting And Repair
Jandy strongly recommends that you call a qualified service technician to perform any repairs on the filter/ ® pump system. To locate a qualified technician, check your local yellow pages or visit www.jandy.com and click on "Product Support." Troubleshooting Symptom... -
Page 14: Service Technician Maintenance
Improper in stal la tion and/or op er a tion will void ® NOTE If you are replacing the motor, Jandy strongly the warranty. recommends that a qualified service technician or electrician properly disconnect the electrical 6.2.1 Blocked Impeller... -
Page 15: Impeller Replacement
Page 15 Backplate Diffuser O-Ring Diffuser Screws with Washers (2) Self Sealing Left Dif fus er Handed Screw Motor Backplate O-ring Screws with Diffuser Washers (2) Impeller Mechanical Seal Motor Backplate Dif fus er O-ring Figure 6. Diffuser and Impeller Exploded View Figure 3. -
Page 16: Mechanical Seal Replacement
Page 16 Replace the motor shaft cover by inserting the NOTE Prior to replacing the lid, check for debris around the lid o-ring seat, as this will cause air leaks into cover tabs into the slots and rotating the cover the system. -
Page 17: Motor Replacement
To ensure continued safety and reliable operation, See section 6.2.4 for details Jandy requires that you replace the motor with ® the identical HP rating and service factor (Jandy ® only). Have a qualified service technician or electrician properly disconnect the electrical wiring at the pump motor. -
Page 18: Section 7. Product Specifi Cations And Technical Data
Page 18 Section 7. Product Specifications and Technical Data Replacement Parts List To order or purchase parts for Jandy pumps, contact your nearest ® Jandy dealer. If they cannot supply you with what you need, contact ® Jandy customer service at 707.776.8200 or send an e-mail message to ®... -
Page 19: Exploded View
2 (qty 8), 16 (qty 8) 1 (qty 4), 17 (qty 4) 4, 15 10 (qty 2) 3, 15 4 (qty 2), 15 (qty 2) 2, 13 7 (qty 2), 18 (qty 2) Figure 10. SHPF and SHPM Exploded View... -
Page 20: Shpf And Shpm Pump Curves
Page 20 SHPF and SHPM Pump Curves Jandy Stealth Series High Head Pumps Feet of ® Head Full Rated (SHPF) and Max-Rated (SHPM) P S I 120.0 100.0 80.0 3 HP SHPF 60.0 2 HP SHPF/ 2.5 SHPM 40.0 2.5 HP SHPM/ 1.5 HP SHPF/... -
Page 21: Physical And Operational Specifi Cations
Page 21 Physical and Operational Specifications 7.4.1 SHPF Pump Specifications Model No. Voltage Amps Pipe Size Carton Weight Overall Length 'A' SHPF.75 208-230/115 6.0-5.6/11.2 2-2½" 43 lbs. " SHPF1.0 208-230/115 7.8-7.4/14.8 2-2½" 45 lbs. 32¼" SHPF1.5 208-230 9.6-8.8 2-2½" 50 lbs. -
Page 22: Replacement Motor Guide
Page 22 Replacement Motor Guide SHP Replacement Motor Guide A.O Smith / A.O Smith/ Pump Model Pump Model Century Century SHPF .75 B661 SHPF 1.0 B841 SHPM 1.0 B863SE SHPF 1.5 B842 SHPM 1.5 B864SE SHPF 2.0 B843 SHPM 2.0 B865SE SHPF 3.0... - Page 23 Page 23 NOTES...
-
Page 24: Limited Warranty
DE grids, or cartridge elements; or damage caused by running the pump with insufficient quantities of water. LIMITATION OF LIABILITY: This is the only warranty given by Jandy Pool Products, Inc. No one is authorized to make any other warranties on behalf of Jandy Pool Products, Inc. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY.