Scientific Atlanta AllTouch 2000 User Manual

AUX Setup Codes

Optimus 0014, 0046,
CD Players
0051, 0159,
0193, 0319,
Aiwa 0171
0434, 0482
Burmester 0434
Panasonic 0043, 0317
California Audio Labs
Parasound 0434
0043
Philips 0171, 0640
Carver 0171, 0193
Pioneer 0046, 0319,
DKK 0014
0482
Denon 0017, 0887
Proton 0171
Emerson 0319
QED 0171
Fisher 0193
Quasar 0043
Garrard 0434
RCA 0067, 0193,
Genexxa 0046, 0319
0319
Harman/Kardon
Realistic 0193, 0194,
0171, 0187
0434
Hitachi 0046
Rotel 0171, 0434
JVC 0086
SAE 0171
Kenwood 0042, 0051,
Sansui 0171, 0319
0204, 0640,
Sanyo 0193
0695, 0840
Scott 0319
Krell 0171
Sears 0319
LXI 0319
Sharp 0051, 0194,
Linn 0171
0875
MCS 0043
Sherwood 0194
MTC 0434
Sony 0014, 0504
Magnavox 0171, 0319
Soundesign 0159
Marantz 0043, 0171,
Tascam 0434
0194
Teac 0194, 0434
Mission 0171
Technics 0043, 0317
NSM 0171
Victor 0086
Onkyo 0115, 0882
Wards 0067, 0171
Yamaha 0050, 0201
Amplifiers Home Automation
Aiwa 0420 GE
Carver 0283 One For All 0181
Curtis Mathes Radio Shack
0314
Denon 0174 Security System
JVC 0345
Universal X10
Linn 0283
Magnavox 0283
X10
Marantz 0283
Panasonic 0322
Philips 0283
Pioneer 0027, 0314
Sony 0703
Technics 0322
Victor 0345
Wards 0027
Yahama 0368

Programming the Remote Control

Introduction

In addition to operating your digital home
communications terminal (DHCT), you can
®
program the AllTouch 2000 (AT 2000)
Remote Control (remote) to operate your
TV, VCR, CD player, or other electronic
device. To program the remote, use the
following procedures.
Notes:
• The remote requires two AA batteries
(alkaline recommended). A diagram in the
battery compartment of the remote indicates
proper placement of the batteries. When
batteries are properly installed, the light on
the remote blinks each time a key is pressed.
• The AT 2000 Remote Control is not a toy. It
should be kept out of the reach of children
under the age of 6 years.

AT 2000 Remote Control Quick Reference

Sansui
Receivers
Sherwood 0516
ADC 0545 Sony
Aiwa 0135, 0172,
Technics
0203, 1103,
1419
Capetronic 0545
Thorens
Carver 0203, 1103,
Victor
1203
Wards
Denon 1118, 1174
Harman/Kardon
Yamaha
0124, 0203
JBL 0124
JVC 0088
Kenwood 0041, 1041,
1327, 1583
Linn 0203
MCS 0053
Magnavox 0203, 0545,
1103, 1203
Marantz 0053, 0203,
1103, 1203
Onkyo 0149
Optimus 0545, 1037
Panasonic 0053, 0323,
1532
Philips 0203, 1103,
1203
Pioneer 0028, 0545,
1037
Quasar 0053
RCA 0545
Miscellaneous Audio
0254 Jerrold 0473, 0534
Scientific-Atlanta 0474
Starcom 0473
0254
0181
0181
0181

Using Mode Keys

Press the appropriate mode key to switch the remote
control operation to the configured device:
TV VCR CBL

Assigning a Device Code to a Mode Key

Try to use your remote to control your devices. If the
remote does not work for a device, you can assign a
different device code to the appropriate mode key.
Before you begin, make sure you know the brand
name of the device you want to control.
1. Turn on your device.
2. Locate your device brand and device setup code
in the appropriate setup code list in this guide. If
your device brand is not listed, see Searching
the Code Library.
3. Point the remote away from your DHCT, TV,
VCR, or other electronic device.

Device Control

1
TV Mode Key
2
Cable Mode Key
26
AUX Mode Key
28 VCR Mode Key
27
POWERS on or off
15 Functions as follows:
• While in VCR mode,
switches TV/VCR input
• While in TV mode,
switches TV/Video input
• While in CBL mode,
controls Bypass option
Sound Control
21
Adjusts volume
23
Mutes sound

FCC Compliance

This device complies with Part 15 of the FCC Rules.
0203, 1103
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
0172, 1072,
and (2) this device must accept any interference
1172, 1272
received, including interference that may cause
0053, 0323,
undesired operation.
1322, 1323,
1532
Note: This equipment has been tested and found to
1203 comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
0088
designed to provide reasonable protection against
0028, 0172,
harmful interference in a residential installation. This
0203
equipment generates, uses, and can radiate radio
0190
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communication. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
the receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Any changes or modifications not expressly approved
by Scientific-Atlanta could void the user's authority to
operate this equipment.
United States: Scientific-Atlanta, Inc., 5030 Sugarloaf Parkway,
Box 465447, Lawrenceville, GA 30042
Product and service availability subject to change without notice.
All rights reserved. AllTouch, Explorer, Scientific-Atlanta, and the
Scientific-Atlanta logo are registered trademarks of Scientific-Atlanta,
Inc. AT2000 is a trademark of Scientific-Atlanta, Inc. All other
trademarks shown are trademarks of their respective owners.
© 2003 Scientific-Atlanta, Inc.
Printed in USA
Part Number 715117 Rev C
4. On your remote, press and hold SELECT and
the appropriate mode key (CBL, TV, VCR,
AUX) until the light on the remote blinks twice.
5. Using the keypad on your remote , enter the 4-
digit setup code for your device. The light on the
AUX
remote blinks twice.
6. Confirm the setup code works by pointing the
remote toward the device and test the POWER,
VOLUME, and MUTE functions.
Note: Volume and Mute functions do not apply
to all devices (for example, Home Automation
devices).
7. Did the device operate correctly?
• If yes, write down the code that worked in
the Record of Codes section in this guide.
You may need it again if the device code is
accidently erased.
• If no, repeat this procedure from step 2 using
a different setup code.
Viewing and Browsing Control
Functions vary by cable provider
11
9 Selects options in menus and program
guide
3
Displays program guide
25 Displays cable settings or Menu
7 Moves through menus or program
guides
22
Selects and deselects screen item
20 Displays channel and program
information
8 Selects channels, up or down
10
Enters channel numbers or
personal identification number
(PIN) for parental control
5 Views favorite channels
AllTouch
Remote Control
User's Guide
www.scientificatlanta.com
December 2003
Note: Some remote keys may be assigned to
operate one device type only. For example,
volume control may be assigned to the TV only.
If this is the case, you can reprogram the power,
volume, and channel control using other
procedures in this guide.

Record of Codes

Record your setup codes in the following table.
TV
VCR
CBL
AUX
Returns to last channel viewed
6
19
Features vary by cable provider;
some provide access to pay-per-
view features. Note: Explorer
DHCTs provide access through
on-screen options.
24 Navigates through program
guide or settings
4
Exits settings, menus, and
guides
VCR/VOD Control
12 Fast forwards VCR/VOD
13 Records program
14 Stops VCR/VOD
16 Plays VCR/VOD
17 Pauses VCR/VOD
18 Rewinds VCR/VOD
®
2000
®