Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bindicator RS-485
Summary of Contents for Bindicator RS-485
- Page 1 InvisiLink Wireless Radio ™ Installation & Operation Manual...
-
Page 3: Table Of Contents
GENERAL SAFETY DISCONNECT REQUIREMENTS FOR PERMANENTLY INSTALLED EQUIPMENT RS-485/RS-422 EQUIPMENT MATRIX Figure 2: Wiring Diagram RS-422 Figure 3: Wiring Diagram RS-485 (MODBUS) Figure 4: Wiring Diagram RS-422 with 4-20 mA Input Box VI. SET-UP ..............................9 Figure 5: LED Indicator Lights Figure 6. - Page 4 VII. MAINTENANCE ............................12 VIII. TROUBLESHOOTING ..........................13 SAFETY SYMBOLS WARNING: IDENTIFIES CONDITIONS OR PROCEDURES, WHICH IF NOT FOLLOWED, COULD RESULT IN SERIOUS INJURY. RISK OF ELECTRICAL SHOCK. CAUTION: IDENTIFIES CONDITIONS OR PROCEDURES, WHICH IF NOT FOLLOWED, COULD RESULT IN SERIOUS DAMAGE OR FAILURE OF THE EQUIPMENT.
-
Page 5: Handling And Storage
InvisiLink Wireless Radio HANDLING AND STORAGE SAVE THESE INSTRUCTIONS INSPECTION AND HANDLING Do not dispose of the carton or packing materials. Each package should be inspected upon receipt for damage that may have occurred due to mishandling during shipping. If the unit is received damaged, notify the carrier or the factory for instructions. Failure to do so may void your warranty. -
Page 6: General Safety
GENERAL SAFETY AUTHORIZED PERSONNEL All instructions described in the document must be performed by authorized and qualified service personnel only. Before installing the unit, please read these instructions and familiarize yourself with the requirements and functions of the device. The required personal protective equipment must always be worn when servicing this device. -
Page 7: Product Description
PRODUCT DESCRIPTION FUNCTION InvisiLink is a wireless radio solution for devices that communicate via RS-485 or RS-422. A radio is connected to both the measuring device, like a Yo-Yo or controller, and the receiving device, like an ORB. Then the InvisiLink radio sends data back and forth between the devices. -
Page 8: Mechanical Installation
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. MOUNTING CONSIDERATIONS • Mounting hardware is not supplied by Bindicator. • When mounting the enclosure ensure there is enough clearance to open the front door completely. Removal, insertion, and wiring of the modular PCB is done through the front of the unit. -
Page 9: To Mount The Invisilink Enclosure
5. Clean enclosure of any debris, replace the board back into the enclosure, using all four (4) mounting screws. 6. Determine desired location for mounting the unit. TO MOUNT THE INVISILINK ENCLOSURE 1. Hold the enclosure against the wall in the desired location and mark the positions of the mounting holes. -
Page 10: Electrical Installation
Kislter-Morse Ultrawave Kistler-Morse MVS Kistler-Morse STXplus Kistler-Morse SVS2000 Kistler-Morse Weigh II Niagara Meters 5600 Controller Note: RS-485 Communication will be programmed at a baud rate of 115200; RS-422 Commuication will be programmed at a baud rate of 9600. WRL180213 Rev. B... - Page 11 Figure 2: Wiring Diagram RS-422 Figure 3: Wiring Diagram RS-485 (MODBUS) WIRING DIAGRAM RS-422 WIRING DIAGRAM RS-485 (MODBUS) Figure 6. Figure 6. POWER BOARD POWER BOARD WIRELESS BOARD WIRELESS BOARD 4 3 2 4 3 2 9 8 7 6...
- Page 12 WIRING DIAGRAM RS-422 W/4-20 Figure 4: Wiring Diagram RS-422 with 4-20 mA Input Box Figure 6. This Power Board is mounted under the Wireless Board to the right. The (2) boards are shown side-by-side for clarity. Ch. 4 Ch. 3 Ch.
-
Page 13: Vi. Set-Up
No additional programming is required. All radio enclosures should automatically begin sending and receiving signals. NOTE: Communication device types cannot be mixed. RS-485 devices must be connected to another RS-485 device; it will not receive signals to or from a RS-422 device. - Page 14 Figure 7. Point-to-Point (Multi Device) RS485 RS485 RS422 RS422 InvisiLink InvisiLink Remote Base Note 2 Note 1 Device Device Device Device N= Number of Devices = 10 for RS422 = 32 for RS485 Figure 8. 4-20 mA Point-to-Point RS422...
- Page 15 TX/RX Mode Switches 1 & 2 Switches 5 & 6 RS-485/422 Termination = Not used = Point-to-Point Switches 3 & 4 = 2-wire RS-485 = 2-wire RS-485 = Multipoint-Base Termination = Factory Reserved = 4-wire RS-422 = Multipoint-Remote = None...
- Page 16 VII. MAINTENANCE PREVENTATIVE MAINTENANCE See ORB 4-20mA Input Box IOM for specific maintenance and possible replacement parts for the ORB 4-20mA Input Box unit. There is no preventative maintenance for a single unit radio. REPLACEMENT PARTS LUC044016 Extended Range Antenna, 2 ft (61 cm) Connection Cable...
- Page 17 VIII. TROUBLESHOOTING For technical or service questions, please call the manufacturer Customer Support at 1-800-788-9242. For detailed dimensional drawings, go to www.bindicator.com SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Radio(s) are not powered on Make sure the Indicator LED is red; if not...
- Page 18 NOTES WRL180213 Rev. B...
- Page 19 NOTES WRL180213 Rev. B...
- Page 20 150 Venture Boulevard Spartanburg, SC 29306 Tel: (800) 778-9242 2014 All rights reserved. Fax: (864) 574-8063 All data subject to change without notice. sales@bindicator.com www.bindicator.com WRL180213 Rev. B...