320709 Gas Hedge Trim EN_320707 Gas Hedge Tri#1D84A8.qxd 7/29/10 11:23 AM Page 5 Warnings - Don’ts Always use trimmer properly. Cut only types and size of growth described in the Trimming section of this manual. Don’t use trimmer with one hand, keep both hands on handles with fingers and thumbs encircling the handles, while blades are Overloading or abusing your hedge trimmer can cause moving, and engine is running.
Don’t operate your trimmer if there is an accumulation of illustrated (Figure 1). On Model SGHT30 use the set of studs debris around the muffler, and cooling fins. which places the handle in the most comfortable position for you.
320709 Gas Hedge Trim EN_320707 Gas Hedge Tri#1D84A8.qxd 7/29/10 11:23 AM Page 7 Operation If the engine needs to be reinstalled: 1. Install the engine by first aligning the hex drive on the trimmer gear housing with the single sided hex socket in WARNING - DANGER the engine.
320709 Gas Hedge Trim EN_320707 Gas Hedge Tri#1D84A8.qxd 7/29/10 11:23 AM Page 8 Starting a Warm Engine Starting a Cold Engine 1. Slide ignition switch to START position. The trimmer has a Start/Stop ignition switch which must be used for starting and stopping the engine. 2.
320709 Gas Hedge Trim EN_320707 Gas Hedge Tri#1D84A8.qxd 7/29/10 11:23 AM Page 9 Maintenance Lubrication Trimming A few drops of a light #10 oil should be placed on the back edge of each blade guard at each adjusting screw approximately WARNING - DANGER after every 4 hours of normal operation.
320709 Gas Hedge Trim EN_320707 Gas Hedge Tri#1D84A8.qxd 7/29/10 11:23 AM Page 10 Service A. Troubleshooting Problem Remedy Cause 1. Blades don’t cut Have blades sharpened and adjusted. Blades are dull or not adjusted properly. cleanly. 2. Blades don’t Re-install engine following the assembly instructions. (pg. 7) Engine is not seated properly on the gear move when housing.
320709 Gas Hedge Trim EN_320707 Gas Hedge Tri#1D84A8.qxd 7/29/10 11:23 AM Page 11 Service Maintenance Guide This chart shows necessary EPA emission maintenance information for fuel tanks/systems and Exhaust Port Cleaning intervals. COMPONENT/ MAINTENANCE REQ’D SKILL DAILY OR EVERY 3 MONTHS YEARLY 600 SYSTEM PROCEDURE...
320709 Gas Hedge Trim EN_320707 Gas Hedge Tri#1D84A8.qxd 7/29/10 11:23 AM Page 12 Carburetor Adjustment e. Idle Speed Adjustment 1. General Units with Cutting Attachments. NOTE:The diaphragm carburetor has three external Turn "idle" speed adjustment screw CW (clockwise) until adjustments. Each adjustment affects the others. cutting attachment begins to turn, then turn screw out CCW (counter clockwise) until attachment stops turning.
320709 Gas Hedge Trim EN_320707 Gas Hedge Tri#1D84A8.qxd 7/29/10 11:23 AM Page 14 Cutting Bar and Side Handle Assembly - Single Edge Hedge Trimmer No. Part No. Description Qty. 300000 Gear Housing Assembly 16-54B 1/4-28 Whiz Flange Locknut (For Model 2230S) 300300 Frame Bar Brace 300200...
320709 Gas Hedge Trim EN_320707 Gas Hedge Tri#1D84A8.qxd 7/29/10 11:24 AM Page 18 SV-5H/2 ENGINE PARTS Fuel System Explosion F ITEM PART # QTY. DESCRIPTION / REMARKS 90027505015 SCREW 5X15 A350000300 TANK, FUEL / INCLUDES ITEM 3 13104528230 SPACER V137000030 GROMMET GASKET KIT 13201309820...
Page 19
Mantis Dealer. equipment. Any implied warranty, including merchantability of fitness for a particular purpose, Engines for all gasoline powered products are shall not extend beyond the written warranty period.
Need help?
Do you have a question about the SGHT30 and is the answer not in the manual?
Questions and answers