Connecting To The Drain; Adjusting The Feet; Electrical Connection - Beko WMP 511W User Manual

A
WARNING
Ensure that the cold and hot water connections are made correctly
when installing the product. Otherwise, your laundry will come out
hot at the end of the washing process and wear out.
Tighten all hose nuts by hand. Never use a wrench when
tightening the nuts. Open the taps completely after making the
hose connection to check for water leaks at the connection
points. If any leaks occur, turn off the tap and remove the nut.
Retighten the nut carefully after checking the seal. To prevent
water leakages and damages caused by them, keep the taps
closed when the machine is not in use.

2.5 Connecting to the drain

• The end of the drain hose must be directly connected to
the wastewater drain or to the washbasin.
A
WARNING
Do not remove the transportation locks before taking out the
packaging reinforcement.
• The hose should be attached to a height of at least 40 cm,
and 100 cm at most.
• In case the hose is elevated after laying it on the floor level
or close to the ground (less than 40 cm above the ground),
water discharge becomes more difficult and the laundry
may come out excessively wet. Therefore, follow the
heights described in the figure.
• To prevent flowing of dirty water back into the machine and
to allow for easy discharge, do not immerse the hose end
into the dirty water or do not drive it in the drain more than
15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be
stepped on and the hose must not be pinched between the
drain and the machine.
• If the length of the hose is too short, use it by adding
an original extension hose. Length of the hose may not
be longer than 3.2 m. To avoid water leak failures, the
connection between the extension hose and the drain
hose of the product must be fitted well with an appropriate
clamp as not to come off and leak.

2.6 Adjusting the feet

A
WARNING
In order to ensure that the product operates more silently and
vibration-free, it must stand level and balanced on its feet. Balance
the machine by adjusting the feet. Otherwise, the product may
move from its place and cause crushing and vibration problems.
Loosen the lock nuts on the feet by hand. Adjust the feet until
the product stands level and balanced. Tighten all lock nuts
4 / EN
again by hand.
A
WARNING
Do not use any tools to loosen the lock nuts. Otherwise, they will
get damaged.

2.7 Electrical connection

Connect the product to a grounded outlet protected by a 13
A fuse. Our company shall not be liable for any damages
that will arise when the product is used without grounding in
accordance with the local regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after
installation.
• If the current value of the fuse or breaker in the house is
less than 13 Amps, have a qualified electrician install a 13
Amp fuse.
• The voltage specified in the "Technical specifications"
section must be equal to your mains voltage.
• Do not make connections via extension cables or multi-
plugs.
B
WARNING:
Damaged power cables must be
replaced by the Authorized Service Agents.
Electrical requirements
Before you insert the plug into the wall socket make sure
that the voltage and the frequency shown in the rating label
corresponds to your electricity supply.
We recommend that this appliance be connected to the mains
supply via a suitable switched and fused socket in a readily
accessible position.
Should the mains lead of the appliance become damaged or
need replacing at any time, it must be replaced by a special
purpose made mains lead which can only be obtained from a
Authorised Service Agent.
B
WARNING:
This appliance must be earthed
If the fitted moulded plug is not suitable for your socket, then
the plug should be cut off and an appropriate plug fitted.
Destroy the old plug, which is cut off as a plug with a bared
cord could cause a shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance incorporates a 13A
fuse. Should the fuse need to be replaced an ASTA approved
BS1362 fuse of the same rating must be used. Do not forget
to refit the fuse cover. In the event of losing the fuse cover,
the plug must not be used until a replacement fuse cover has
been fitted. Colour of the replacement fuse cover must be the
same colour as that visible on the pin face of the plug. Fuse
covers are available from any good electrical store.
Washing Machine / User's Manual