1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 323HD60
  6. Operator's manual

Husqvarna 323HD60 Operator's Manual

Hide thumbs Also See for 323HD60:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
Operator ' s manual
323HD60 325HD60
X-SERIES
325HD75
X-SERIES
Please read the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 323HD60

Summary of Contents for Husqvarna 323HD60

  • Page 1 Operator ′ s manual 323HD60 325HD60 X-SERIES 325HD75 X-SERIES Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.

  • Page 3: Table Of Contents

    CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the Symbols ............... design and appearance of products without prior notice. CONTENTS Contents ..............

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment FIRST AID KIT Always have a first aid kit nearby. IMPORTANT! Whenever you use the hedge trimmer you must use personal protective equipment that is approved by the authorities. Personal protective equipment does not eliminate the risk of injury, but it can reduce the degree of injury in the event of an accident.
  • Page 5 SAFETY INSTRUCTIONS Hand guard For mufflers it is very important that you follow the instructions on checking, maintaining and servicing your machine. See The hand guard prevents hands from coming into contact with instructions under the heading Checking, maintaining and the moving blades, for example, if the operator loses grip on servicing the machine’s safety equipment.

  • Page 6: Checking, Maintaining And Servicing The Machine ' S Safety Equipment

    SAFETY INSTRUCTIONS Checking, maintaining and servicing the blades move when the throttle trigger is in the idle position then the carburettor idle setting must be adjusted. the machine ′ s safety equipment See instructions under the heading Maintenance. IMPORTANT! All servicing and repair work on the machine requires special training.

  • Page 7: Gear Housing

    SAFETY INSTRUCTIONS Muffler Cutter guard • Never use a machine that has a faulty muffler. • Check that the blade guard is not damaged or distorted. • Replace the blade guard if it is bent or damaged. • Regularly check that the muffler is securely attached to the machine.

  • Page 8: General Safety Precautions

    SAFETY INSTRUCTIONS General safety precautions Fuel safety IMPORTANT! The machine is only designed for cutting branches and twigs. • Always use a fuel container with an anti-spill valve. Never use the machine if you are tired, if you have drunk •...

  • Page 9: Safety Instructions When Using The Hedge Trimmer

    SAFETY INSTRUCTIONS Safety instructions when using the Safety instructions while working hedge trimmer WARNING! The machine can cause serious • Always ensure you have a safe and stable working personal injury. Read the safety instructions position carefully. Learn how to use the machine. •...

  • Page 10: Basic Working Techniques

    SAFETY INSTRUCTIONS Safety instructions after completing work Basic working techniques (325HD60, 325HD75) • The hedge trimmer’s rear handle can be set in three positions by pulling out the catch. See figure. When the • The transport guard should always be fitted to the cutting handle is adjusted the hedge trimmer should be idling or attachment when the machine is not in use.

  • Page 11: What Is What

    WHAT IS WHAT? What is what? 1 Operator′s manual 13 Lock for handle (325HD60, 325HD75) 2 Grease filler cap 14 Fuel tank 3 Gear housing 15 Fuel cap 4 Blades 16 Air purge 5 Cutter guard 17 Choke control 6 Front handle 18 Air filter cover.

  • Page 12: Fuel Handling

    Mixture 1:50 (2%). When refuelling, open the fuel cap slowly so • If HUSQVARNA two-stroke oil is not available, you may that any excess pressure is released gently. use another two-stroke oil of good quality that is intended Tighten the fuel cap carefully after refuelling.

  • Page 13: Starting And Stopping

    STARTING AND STOPPING Check before starting Starting and stopping Starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. WARNING! The gear housing and clutch drum must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.

  • Page 14: Warm Engine

    STARTING AND STOPPING Warm engine Stopping Ignition: Set the stop switch to the start position. The engine is stopped by switching the ignition off using the stop switch. Choke: Set the choke control in the choke position and then back to its original position (B). This only engages the start throttle setting without any choke.

  • Page 15: Maintenance

    CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops. Your Husqvarna product has been designed and manufactured to specifications that reduce harmful Rec. idle speed 2700 rpm emissions.

  • Page 16: Muffler

    MAINTENANCE Fine adjustment of the idle speed T CAUTION! For optimum adjustment of the carburettor, contact a qualified dealer/service workshop that has a Adjust the idle speed with the idle adjustment screw T, if revolution counter at their disposal. adjustment is necessary. First turn the idle adjustment screw T clockwise until the blades start to move.

  • Page 17: Cooling System

    A dirty or blocked cooling system results in the machine overheating which causes Always use HUSQVARNA filter oil, art. no. 503 47 73-01. The damage to the piston and cylinder. filter oil contains a solvent to make it spread evenly through the filter.

  • Page 18: Spark Plug

    There is a grease nipple on the gearbox. Use a grease gun to top up with grease. This should be carried out after approximately every 20 working hours. Use Husqvarna special grease, No. 503 98 96-01. 1 Clean the outside of the machine.
  • Page 19 MAINTENANCE Weekly maintenance Monthly maintenance 1 Clean the fuel tank. 2 Clean the outside of the carburettor and the space around 3 Clean the fan and the area around it. 4 Check the fuel filter and the fuel hose. Replace if 1 Check the starter, the starter cord and the recoil spring.

  • Page 20: Technical Data Technical Data

    TECHNICAL DATA Technical data Technical data 323HD60 325HD60 325HD75 Engine Cylinder displacement, cm 24,5 24,5 24,5 Cylinder bore, mm Stroke, mm Idle speed, rpm 2700 2700 2700 Recommended max. speed, rpm 11000-12600 11000-12600 11000-12600 Max. engine output, acc. to ISO 8893...

  • Page 21: Ec-Declaration Of Conformity (Applies To Europe Only)

    Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 323HD60, 325HD60 and 325HD75 from 2002’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:...
  • Page 22 ´®z+H2"¶6-¨ ´®z+H2"¶6-¨...
  • Page 24 1140180-26 ´®z+H2"¶6-¨ ´®z+H2"¶6-¨ 2003-03-25...

This manual is also suitable for:

325hd60 x-series325hd75 x-series

Table of Contents