TABLE OF CONTENTS SPECIFICATIONS .............................. 3 ACCESSORIES/PACKAGE LIST ........................3 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING ............4 Precaution to replace Optical block ........................4 ELECTRICAL MAIN PARTS LIST ........................5-8 TRANSISTOR ILLUSTRATION .......................... 9 WIRING-1 (MAIN 2B) ............................10 WIRING-2 (DECK) ............................
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
IC DESCRIPTION IC, CXA1992AR Pin No. Pin Name Description Output terminal for focus error amplifier. Internally connected to window comparator input for bias condition. Input terminal for focus error. FDFCT Capacitor connection terminal for time constant used when there is defect. This pin is connected to GND via capacitor when high frequency gain of the focus servo is attenuated.
Page 32
Pin No. Pin Name Description RF_O Output terminal of RF summing amplifier. Checkpoint of Eye pattern. Anti-reverse input terminal for RF summing amplifier. RF_M The gain of RF amplifier is decided by the connection resistance between RF_M and RFO terminals. This is a pin where the selection time constant is externally connected to control the RFTC RF level.
IC DESCRIPTION IC, CXD2540Q Pin No. Pin Name Description Focus OK input. Used for SENS output and the servo auto sequencer. Spindle motor output filter switching output. (Not connected) Spindle motor on/off control output. (Not connected) Spindle motor servo control. Spindle motor servo control.
Page 34
Pin No. Pin Name Description LRCK64 DA12 output when PSSL=1. 64-bit slot LR clock when PSSL=0. (Not connected) GTOP DA11 output when PSSL=1. GTOP output when PSSL=0. (Not connected) XVCF DA10 output when PSSL=1. XUGF output when PSSL=0. (Not connected) XPCLK DA09 output when PSSL=1.
Page 35
Pin No. Pin Name Description CNIN Track jump count signal input. DATO Serial data output to SSP. XLTO Serial data latch output to SSP. Latched at the falling edge. CLKO Serial data transfer clock output to SSP. Mirror signal input. Used when the number of tracks is 128 or more for the 2N-track jump and MIRR M track move of the auto sequencer.
Page 36
IC, CL680 Pin No. Pin Name Description — No connection. — GND. CD BCK Bit clock input from CD DSP. CD DATA Data input from CD DSP. CD LRCK LRCK input from CD DSP. CD C2PO C2 pointer input from CD DSP. —...
Page 37
Pin No. Pin Name Description Y OUT Video signal “Y” OUT. (Not connected) AVDD DAC — Analog power supply (DAC) 3.3V. AGND DAC — Analog ground. R REF Reference resistor input. (Pull down) V REF Voltage reference input. (Not connected) AVDD DAC —...
Page 38
Pin No. Pin Name Description __________ HINT Micon interface. (Host interrupt) CDG SCK CD-G serial clock input. — Ground. Micon interface. (Host clock) VDD3 — Power supply 3.3V. HD IN Micon interface. (Host data in) VDD3 — Power supply 3.3V. HSEL Micon interface.
Page 39
IC, LC74781M Pin No. Pin Name Description VSS1 — GND connection terminal. (Digital ground terminal). Xtal IN External X’tal and capacitor for internal sync generator, or the external clock are Xtal OUT connected to this terminal. (2fsc or 4fsc). (Pin3: Not connected) Either the external clock input mode or the X’tal generator mode is selected by this selector CTRL1 terminal.
Page 40
Pin No. Pin Name Description ______________ ______________ Controls whether or not to input the VSYNC signal to the SEPIN input. L: to input the VSYNC CTRL3 ______________ signal. H: not to input the VSYNC signal. (Connected to Vdd) System reset input terminal. Pull-up resistor is built-in. (Hysteresis input). (Pull down) VDD1 —...
Page 41
IC, µPD78016CFG-578-AB8 Pin No. Pin Name Description RBPLS RADIAL BALANCE PLUS. AMUTE AUDIO ANALOG MUTE (H=MUTE ON). GFS. XVCDMD AUDIO/VIDEO CD MODE (L=VCD=SPINDLE GAIN UP). DOUT MUTE CONT. EMPH EMPHASIS. SQSO SQDATA FROM CD. SQCK SQCLK TO CD. — GND. SWNT SW TV OUT MODE (L=NTSC).
Page 42
Pin No. Pin Name Description 8.0MHz CERALOCK. (Pull down) — GND. — Not used. 5.0VDD. AVSS — GND. XMPGRST MPEG BLOCK IC RESET. HSEL ADDRESS/DATA SEL TO CL680. INLSW INSIDE LIMIT SW . RWSEL2 CD-RW SELECT1. L=CD-RW. OSDXCS OSD CHIP SELECT. (Pull down) ABSEL CXA1992A/B SELECT (L=CXA1992A).
Page 43
IC, SM5878M Pin No. Pin Name Description MODE = H: Soft mute ON/OFF terminal. (Mute at H). MUTE MODE = L: Attenuator level DOWN/UP terminal. (DOWN at H). (Pull down) DEEM De-emphasis ON/OFF terminal. (De-emphasis ON at H). Oscillator clock output. (16.9344 MHz). DVSS —...
Page 44
IC, LC867140V-5T17 Pin No. Pin Name Description O-XBUSY/CE READY/BUSY I/O from VCD MICON. Tuner, chip enable output for PLL communication. O-DATA Tuner, serial data output for PLL communication. Sound processor control. O-CLK Tuner, clock output for PLL communication. — No connected. O-CLK SFT Clock shift control.
Page 45
Pin No. Pin Name Description — No connected. I-CD TEST — No connected. I-TU TEST — No connected. 64-66 COM0-2 LCD common output. (No.22-24) — No connected. VSS2 — GND. VDD2 — Power supply positive polarity (+) terminal. O-CD ON CD/VCD power supply control.
CD MECHANISM EXPLODED VIEW 1/1 SHAFT,SLIDE SF-P101NR CHASSIS SPINDLE MOTOR C,B MOTOR(M3) CD MECHANISM PARTS LIST 1/1 REF. NO PART NO. KANRI DESCRIPTION 1 S2-121-A28-400 COVER GEAR 2 S2-511-A21-000 GEAR MIDDLE 3 S2-511-A21-100 GEAR,DRIVE A S1-PN2-03R-OSE SCR PAN PCS 2-3 B 87-261-073-410 SCR S-TPG FLT 2.6-6 ALL M8-ZZK-E90-070...