Download Print this page
American Standard 1662 Series Installation Instructions
American Standard 1662 Series Installation Instructions

American Standard 1662 Series Installation Instructions

Shower system kits

Advertisement

Quick Links

SHOWER SYSTEM KITS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Recommended Tools & Materials
Phillips Screwdriver
ROUGHING-IN DIMENSIONS
13mm
(1/2")
1/2" NPT
(48" - 60")
(OPTIONAL)
TO FINISHED
FLOOR
127mm
(5")
82mm
45mm
(3-1/4")
(1-3/4")
70mm
(2-3/4")
1660.225
549mm
(21-5/8")
25mm
(1")
OPTIONAL TO FINISHED FLOOR
USUALLY BETWEEN
915mm
TO
1525mm
(60")
(36")
1
INSTALL WALL SUPPLY
Supply to WALL SUPPLY (1) is 1/2" NPT. See rough-in above for detailed information.
Install RUBBER SEAL (2) onto WALL SUPPLY (1).
Apply sealant or teflon tape to threads of 1/2" NPT supply nipple. Thread WALL SUPPLY (1)
onto supply nipple making a water tight seal. WALL SUPPLY (1) with RUBBER SEAL (2)
should be tight against finished wall.
Hammer
32mm
(1-1/4")
1498mm
(59")
53mm
(2-1/16")
1/2" NPSM HOSE
CONNECTION
(2-1/2")
RUBBER GASKET
FINISHED WALL
1660.236
65mm
849mm
(2-1/2")
(33-3/8")
900mm
(35-3/8")
600mm
(23-5/8")
86mm
(3-3/8")
(3-3/8")
FINISHED FLOOR
Turn off hot and cold water
CAUTION
supplies before beginning.
Installation
Instructions
1662 SERIES
Pencil
1660.500
1/2" NPSM
65mm
1660.502
1/2" NPSM
1660.843
1/2" NPSM
81mm
(3-1/4")
94mm
(3-3/4")
247mm
(9-3/4")
86mm
1660.628
1/2" NPSM
1/2" NPSM
Certified to comply with ANSI A112.18.1
M 9 6 8 6 3 7 R ev 1. 4
6mm (15/64")
Drill Bit
Electric Drill
57mm
42mm
(2-1/4")
(1-5/8")
1660.550
250mm
(9-7/8")
67mm
(2-5/8")
146mm
(5-3/4")
1660.505
1/2" NPSM
1660.143
1/2" NPSM
76mm
(3")
(2-1/2")
94mm
(3-3/4")
239mm
252mm
(9-3/8")
(9-7/8")
1660.638
1
2
24mm
(1")
191mm
(7-1/2")
1/2" NPSM
A950646
1660.743
1/2" NPSM
65mm
1660.741
1/2" NPSM
1/2" NPT
APPLY SEALANT
OR TEFLON TAPE

Advertisement

loading
Need help?

Need help?

Do you have a question about the 1662 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for American Standard 1662 Series

  • Page 1 Apply sealant or teflon tape to threads of 1/2" NPT supply nipple. Thread WALL SUPPLY (1) onto supply nipple making a water tight seal. WALL SUPPLY (1) with RUBBER SEAL (2) should be tight against finished wall. Installation Instructions 1662 SERIES Hammer Pencil 1498mm (59") 1660.500...
  • Page 2 INSTALL LOWER SUPPORT BRACKET The SLIDE BAR works best when secured to the wall studs or cross brace using the WOOD SCREWS. If a mounting into the studs is not possible, use appropriate wall fasteners to provide secure installation. Mark a vertical center line in the location you wish to install the SLIDE BAR.
  • Page 3 INSTALL SLIDE BAR INTO MOUNTING BRACKETS Install the SLIDE BAR (1) back into the lower MOUNTING BRACKET (2). IMPORTANT: The slot at the bottom of the slide bar must face toward the wall. Rotate the slide bar until it locks into place and cannot be turned.