Ice Maker; Water Supply; Water Dispenser; Turning Off The Refrigerator - Dometic Rm1350 User Manual

IcE makER

Rm1350 Im, Rm1350 WIm & RmE1350 WIm

Before the ice maker can operate, make sure that:
• The refrigerator is connected to 120 V AC .
• The water valve supplying the refrigerator is turned on.
• The ice level bail arm is in its fully down position.
when the ice maker thermostat senses the preset temperature
for the ejection of the ice cubes, the fingers will start to rotate,
dumping any ice cubes and filling the mold with water.
when the storage container is full, the bail arm will come in
contact with the ice cubes. The bail arm cannot return to the full
down position and the ice production is stopped until the bin is
emptied, or ice cubes are removed.
To prevent water from splashing out of the mold assembly when
your recreational vehicle is moving, raise the bail arm to the full
"uP/OFF" position about 1-1/2 hours before departing. This will
allow the water in the mold to freeze.

WatER SUpply

The water supply system must have a minimum pressure of
15 pounds per square inch gauge (psig). A 1/4" diameter water
line to the water valve should be used at the rear of the refrig-
erator. The water line must have a manual shutoff valve placed
where it is easily accessible.
The maximum water level is represented by a thin line. It is
essential that the water level does not exceed this line!
Maximum
water level
If necessary change the water flow by adjusting the water sup-
ply, see the step-by-step instruction in the following section
ADjusTING ThE sIzE OF CuBEs.
opERatInG InStRUctIonS
Ice level
bail arm
Down
position
adjUStInG thE SIzE oF cUbES
If the ice maker was cleaned and drained, no ice cubes
will be dumped into the bin during the first cycle.
The first few cycles may have small cubes due to air trapped
in the water lines. The first container of ice cubes should be
dumped if the water system has been winterized or not used
for several weeks. Once the ice maker has run through several
cycles and if cubes are to small or sticking together, adjustment
is necessary on the amount of water entering the mold.
TO ADjusT ThE sIzE OF CuBEs, FOLLOw ThEsE sTEPs:
1. Remove the protective cover from the ice maker
mechanism.
2. Locate the adjusting screw under the protective
cover. Turn the screw counterclockwise to increase
the size of cubes.
3. Turn the screw clockwise to decrease the cube size
or if the mold is overfilling, and the cubes are stuck
together.
To prevent overfilling, do not turn the adjustment
screw more than one revolution at a time. Allow the
ice maker to cycle several times before another adjust-
ment is made. Be sure to replace the protective cover
on the cycle after the adjustments are complete.

WatER dISpEnSER

Rm1350 WIm & RmE1350 WIm

First, verify that the water valve
supplying the refrigerator is turned
on. Then, to dispense water at the
door, simply press the lever. This
will activate a switch which turns
on an electric water valve at the
back of the refrigerator. water will
flow through a separate tube and out
of the dispenser.
To keep the water fresh, it is recommended to use the dispenser
every day. If new installation, or used infrequently, dispense
numerous glasses of water before use.

tURnInG oFF thE REFRIGERatoR

The refrigerator may be shut off while in any mode of opera-
tion by pressing the main power ON/OFF button (OFF
position). This shuts off all DC power to the refrigerator,
including the interior light.
If the refrigerator will not be in operation for a period of weeks,
it should be emptied, defrosted, cleaned and the doors left ajar.
The ice trays should also be dried and kept outside the cabinet.
-  -
Adjusting screw
Cover
Press
lever