Cisco 7600 Series Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. 7600 Series
  6. Manual
Cisco 7600 Series Manual

Cisco 7600 Series Manual

Router supervisor engine and route switch
Hide thumbs Also See for 7600 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Configuration Manual, User Manual
Enlarged version
Cisco 7600 Series Router
Supervisor Engine and
Route Switch Processor Guide
January 2008
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-10100-04

Advertisement

Table of Contents
loading

Related Manuals for Cisco 7600 Series

Summary of Contents for Cisco 7600 Series

  • Page 1 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide January 2008 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-10100-04...
  • Page 2 OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. CCVP, the Cisco logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.;...

  • Page 3: Table Of Contents

    2-10 QoS on the RSP720-10GE 2-10 Supervisor Engine 720 and Supervisor Engine 32 2-12 Front-Panel Controls (RSP720, RSP720-10GE, Sup720, Sup32) 2-12 Front-Panel LEDs (RSP720, RSP720-10GE, Sup720, Sup32) 2-13 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...
  • Page 4 1GE Uplink Ports and Cabling Specifications 10GE Uplink Ports and Cabling Specifications GBIC Module Cabling Specifications Console Port Cabling Specifications and Pinouts Console Port Cabling Specifications Console Port Signals and Pinouts Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...
  • Page 5 Cleaning the Fiber-Optic Connectors B-15 LX/LH GBIC and MMF Cable Considerations B-16 Patch Cord B-16 Patch Cord Configuration Example B-16 Patch Cord Installation B-17 N D E X Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...
  • Page 6 Contents Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...

  • Page 7: Contents

    Preface This guide describes the route switch processors and supervisor engines supported by Cisco 7600 series routers. It also provides technical specifications for these modules and describes cable and connector specifications. Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install, Caution replace, or service the equipment described in this document.

  • Page 8: Document Organization

    Means reader be careful. You are capable of doing something that might result in equipment damage or Caution loss of data. Means reader take note. Notes contain helpful suggestions or references to materials not contained in Note this document. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide viii OL-10100-04...

  • Page 9: Warning Definition

    Statement 1071 SAVE THESE INSTRUCTIONS See Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers for translations of warnings and information about the compliance and safety standards with which Cisco 7600 series routers conform.

  • Page 10: Obtaining Documentation, Obtaining Support, And Security Guidelines

    For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html...

  • Page 11: Chapter 1 Cisco 7600 Product Overview

    C H A P T E R Cisco 7600 Product Overview This chapter provides an overview of the Cisco 7600 series routers and describes interface and port addresses on the routers. It contains the following sections: Cisco 7600 Series Routers, page 1-1 •...

  • Page 12: Supported Hardware

    – Specific combinations of supervisor engines or RSPs and modules may not be supported in Note your chassis. See the Supported Hardware for Cisco 7600 Series Routers guide for information about which combinations are not supported. Hot-swappable fan assembly •...

  • Page 13: Features

    • The Route Switch Processor 720 (RSP720) is the newest supervisor Note engine for the Cisco 7600 series routers. It is available in Cisco IOS Release 12.2SRB and later releases. Cisco IOS Release 12.2SRC introduces support for the RSP720-10GE Note (an RSP with 10 Gigabit Ethernet uplink ports).
  • Page 14 The Sup720 SP/RP, Sup32 RP, and Sup2 SP/RP contain 32-MB or • 64-MB of internal flash memory. Cisco IOS Release 12.2(18)SXF and later releases support the CF adapter as an orderable option (Cisco part number CF-ADAPTER=) for these Sups. In the command-line-interface (CLI), you access internal flash memory Note as bootdisk (CF adapter) or bootflash (non-CF adatper).

  • Page 15: Port Addresses

    Port Addresses Port Addresses Each port (or interface) in the Cisco 7600 series router has several different types of addresses. The physical interface address is the actual physical location (slot and port) of the interface connector within the chassis. The system software uses the physical addresses to control activity within the router and to display status information.

  • Page 16: Mac Addresses

    Each VLAN in the spanning tree has one unique MAC address. This addressing scheme enables the router to identify the state (connected or not connected) of each interface. When you hot swap a module, the MAC address changes with the module. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...

  • Page 17: Chapter 2 Route Switch Processors And Supervisor Engines

    Note switch processor and supervisor engine configurations supported on Cisco 7600 series routers. Be sure to review the release notes for the software version running on your router for information about any restrictions and limitations that might apply.

  • Page 18: C H A P T E R 2 Route Switch Processors And Supervisor Engines

    • Supervisor Engine 32—Supported on all but the Cisco 7603 router. • Supervisor Engine 2—Supported on all but the Cisco 7613 router. The Supervisor Engine 2 is no • longer supported in Cisco IOS Release 12.2SRA and later releases. Although the router can operate with a single supervisor engine or RSP, you can also install a second redundant module (of the same type) in the chassis.
  • Page 19 Overview Table 2-1 lists the RSP and supervisor engine configurations supported on Cisco 7600 series routers. Specific combinations of processors and modules may not be supported in your chassis. See the release notes for your software version for information about supported combinations.
  • Page 20 Requires larger power supplies and a high-speed fan tray • QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t • Cisco IOS Release 12.2SXF is the last release in which the Note Sup720 with PFC3A is supported. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...
  • Page 21 QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t • Note A CompactFlash (CF) adapter with 512-MB bootflash is available for Sup720 modules in Release 12.2(18)SXF and later releases. Use the Cisco part number CF-ADAPTER= for ordering. Supervisor Engine 32 WS-SUP32-GE-3B Nine Gigabit Ethernet uplink ports: eight SFP modules and one •...
  • Page 22 This section describes the Route Switch Processor 720 (RSP720). The Cisco 7600 RSP720 consists of a full-size board and two integrated daughter cards: the MSFC4 and a PFC3C or PFC3CXL. The RSP720 has an integrated switch fabric that interconnects all of the line cards in the Cisco 7600 router with point-to-point 20-Gbps full-duplex serial channels.

  • Page 23: Rsp720 Features

    • Supported Chassis, Line Cards, and Modules The RSP720 supports the following Cisco 7600 chassis, line cards and modules: Supported on all Cisco 7600 routers (including enhanced chassis) except the Cisco 7603 and the • Cisco OSR-7609 SPA interface processors (SIPs) and their shared port adapters (SPAs): 7600-SIP-600, •...

  • Page 24: Rsp720 With 10Ge Uplink Ports

    RSP720 with 10GE Uplink Ports RSP720 with 10GE Uplink Ports Cisco IOS Release 12.2SRC introduces a new RSP720 with 10 Gigabit Ethernet (GE) uplink ports (RSP720-10GE). The Cisco 7600 RSP720-10GE consists of a full-size board and two integrated daughter cards: an MSFC4 and a PFC. The RSP720-10GE has an integrated switch fabric that interconnects all of the line cards in the router with point-to-point 20-Gbps full-duplex serial channels.

  • Page 25: Supported Chassis, Line Cards, And Modules

    Supported Chassis, Line Cards, and Modules The RSP720-10GE supports the following chassis and modules: Supported on the Cisco 7604 and 7609 chassis and the Cisco 7603-S, 7606-S, and 7609-S chassis • If you insert an RSP720-10GE into an unsupported chassis, the RSP720-10GE drops to Note ROMmon and only the console is accessible.

  • Page 26: Rsp720-10Ge Usage Guidelines And Limitations

    RSP720-10GE Usage Guidelines and Limitations Observe the following guidelines when using the RSP720-10GE: • The RSP720-10GE runs the same Cisco IOS software images as the RSP720. The following software image feature sets are available for the RSP720-10GE: ipservices, ipservicesk9, advipservices, advipservicesk9, and adventerprisek9.
  • Page 27 • Configuring 10GE Only QoS Cisco IOS Release 12.2SRC introduces a new command to enable QoS features on 10GE uplink ports only. By default, the router runs in mixed mode, which means that QoS is enabled on both the 10GE uplink ports and the 1GE uplink ports.

  • Page 28: Supervisor Engine 720 And Supervisor Engine 32

    Front-Panel Controls (RSP720, RSP720-10GE, Sup720, Sup32) Table 2-2 describes the front-panel controls on the Route Switch Processor 720 and RSP720-10GE, the Supervisor Engine 720, and the Supervisor Engine 32. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-12 OL-10100-04...

  • Page 29: Front-Panel Leds (Rsp720, Rsp720-10Ge, Sup720, Sup32)

    The module is powering up or a minor hardware fault has occurred. Major hardware problem. The temperature of the supervisor engine or RSP has exceeded the major temperature threshold. Blinking Continuous backplane stall. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-13 OL-10100-04...

  • Page 30: Supervisor Engine 2

    Table 2-5 describes the LEDs. Note In Cisco IOS Release 12.2SR and later releases, the Supervisor Engine 2 is no longer supported on Cisco 7600 series routers. Figure 2-6 Supervisor Engine 2 Front Panel...
  • Page 31 Diagnostic test failed; the module is not operational. (The fault occurred during the initialization sequence.) An overtemperature condition has occurred. (A major threshold has been exceeded during environmental monitoring.) Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-15 OL-10100-04...
  • Page 32 2. VTT = voltage termination. The VTT module terminates signals on the system switching bus. 3. If no redundant supervisor engine is installed and there is a VTT module minor or major overtemperature condition, the system shuts down. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-16 OL-10100-04...

  • Page 33: Preparing For Installation Or Removal

    Determine which chassis slot to install the module in. (See the “Determining Module Location” • section on page 3-3.) Consider cabling for the console and uplink ports. (See Appendix B, “Cable and Connector • Specifications.”) Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...

  • Page 34: C H A P T E R 3 Installing And Configuring Route Switch Processors And Supervisor Engines

    Place a removed component board-side-up on an antistatic surface or in a static-shielding container. • If you plan to return the component to the factory, immediately place it in a static-shielding container. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...

  • Page 35: Tools Required For Module Installation

    Periodically check the resistance value of the antistatic strap. The measurement should be within the Caution range of 1 and 10 megohms (Mohms). Tools Required for Module Installation These tools are required to install modules in the Cisco 7600 series router: Flat-blade screwdriver • Antistatic wrist strap or other grounding device •...

  • Page 36: Installing A Supervisor Engine Or Route Switch Processor

    Fully open both ejector levers on the new module. (See Figure 3-1.) Step 3 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...
  • Page 37 4 PORT OC-12 POS SM MODE PORT 1 CONSOLE SUPERV ISOR2 PORT 2 PCMCIA EJECT OSM-4OC1 2 POS-SI 4 PORT OC-12 POS SM EMI gasket Ejector lever fully extended Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...
  • Page 38 Make sure the ejector levers are fully closed before tightening the captive installation screws. Note Blank module filler plates (Cisco part number 800-00292-01) should be installed in any empty chassis Note slots to keep dust out of the chassis and to maintain consistent airflow through the chassis.

  • Page 39: Removing A Supervisor Engine Or Route Switch Processor

    Place the module on an antistatic mat or antistatic foam, or immediately reinstall the module in another slot. Step 6 Install blank module filler plates (Cisco part number 800-00292-01) in any empty slots to keep dust out Step 7 of the chassis and to maintain consistent airflow through the chassis.

  • Page 40: Hot Swapping (Oir) Modules

    Hot Swapping (OIR) Modules Hot Swapping (OIR) Modules Cisco 7600 series routers provide a feature that allows you to remove and replace a redundant supervisor engine or route switch processor (and other redundant cards) without powering down the router. This feature, called hot swapping or online insertion and removal (OIR), allows you to remove and replace a redundant module without disrupting router operation.

  • Page 41: Connecting To The Console Port

    The console port is an EIA/TIA-232 asynchronous, serial connection with hardware flow control and an RJ-45 connector. The accessories kit that is shipped with your Cisco 7600 series router contains the necessary cable and Note adapters to connect a terminal or modem to the console port. See the “Console Port Signals and Pinouts”...

  • Page 42: Connecting A Modem

    Do not remove the plugs from the optical bores on the fiber-optic cable or the module port or until you Caution are ready to connect the cable. The plugs protect the optical bores and cable from contamination. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 3-10 OL-10100-04...
  • Page 43 (Sup2 only) If you are using the LX/LH GBIC with multimode fiber (MMF), you need to install a patch Step 5 cord between the GBIC and the MMF cable. For instructions, see the “Patch Cord” section on page B-16. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 3-11 OL-10100-04...

  • Page 44: Using Flash Memory Cards

    • In Cisco IOS Release 12.2SRC, the uplink ports on a standby RSP720-10GE are not active and cannot be used for normal traffic. Using Flash Memory Cards The front panel on the supervisor engine or route switch processor has one or two disk slots for flash memory cards.

  • Page 45: Installing A Flash Memory Card

    Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines Using Flash Memory Cards Table 3-3 lists the Cisco product numbers of memory cards supported on Cisco 7600 supervisor engines and route switch processors. Table 3-3 CompactFlash Memory Cards...

  • Page 46: Removing A Flash Memory Card

    Cisco IOS software requirements for the hardware installed on your router. You must have an account on Cisco.com to access the Feature Navigator or Software Advisor tool. Note To determine which software features are supported by your route switch processor or supervisor •...

  • Page 47: Appendix

    3 to 10 lb (1.4 to 4.5 kg) Regulatory Standards Compliance For information about the regulatory standards that Cisco 7600 series routers comply with, see Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide...

  • Page 48: Appendix A Technical Specification

    Appendix A Technical Specifications Regulatory Standards Compliance Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...

  • Page 49: Appendix

    A P P E N D I X Cable and Connector Specifications This appendix lists the cable and connector specifications for the Cisco 7600 route switch processors (RSPs) and supervisor engines. It contains the following information: Limiting Connection Distances, page B-1 •...

  • Page 50: Uplink Port Transceiver Modules

    10GE Uplink Ports (RSP720-10GE only): RSP720-10GE X2-10GB-SR X2-10GB-LR X2-10GB-ER X2-10GB-LX4 X2-10GB-CX4 1GE Uplink Ports: GLC-SX-MM GLC-LH-SM GLC-ZX-SM GLC-T GLC-BX-D GLC-BX-U SFP-GE-S SFP-GE-L SFP-GE-T Supervisor Engine 720 GLC-SX-MM GLC-LH-SM GLC-ZX-SM GLC-T Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...

  • Page 51: 1Ge Uplink Ports And Cabling Specifications

    Supervisor Engine 2 1000BASE-X GBIC modules, which are preinstalled 1GE Uplink Ports and Cabling Specifications Table B-2 describes the 1GE SFP transceiver modules that are used for Cisco 7600 uplink ports. Table B-3 provides cabling specifications. Note Use Category 5 Shielded Twisted Pair cable at the port that supports the10/100/1000-Mbps RJ-45 connector for the RSP720-10GE.
  • Page 52 “Mode-Conditioning Patch Cord Description” section of the document at the following URL: http://www.cisco.com/en/US/products/hw/routers/ps341/prod_module_installation_guide09186a00801cc731.html#wp29618 3. ITU-T G.652 SMF as specified by the IEEE 802.3z standard. 4. Dispersion-shifted single-mode fiber-optic cable. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...

  • Page 53: 10Ge Uplink Ports And Cabling Specifications

    CX4 (copper) — — 49.2 ft (15 m) XENPAK-10GB-CX4 1. Minimum cabling distance for -LR, -SR, -LX4, and -ER modules is 2 m, according to the IEEE 802.3ae standard. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...

  • Page 54: Gbic Module Cabling Specifications

    The console port, which is located on the front panel of the supervisor engine or route switch processor, provides access to the Cisco 7600 router. The following sections provide information about the console port cabling specifications and the port’s signals and pinouts.

  • Page 55: Console Port Signals And Pinouts

    B-1.) If you purchased your cable from Cisco Systems, pin 1 is white on one connector, and pin 8 is white on the other (a rollover cable reverses pins 1 and 8, 2 and 7, 3 and 6, and 4 and 5).

  • Page 56: Adapter (For Connecting To A Pc

    Console Port DB-9 Adapter Pinouts RJ-45-to-RJ-45 RJ-45-to-DB-9 Console Console Port Rollover Cable Terminal Adapter Device Signal RJ-45 Pin RJ-45 Pin DB-9 Pin Signal 1. Pin 1 is connected internally to Pin 8. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...

  • Page 57: Adapter (For Connecting To A Terminal

    Console Port Modem Adapter Pinouts RJ-45-to-RJ-45 RJ-45-to-DB-25 Console Port Rollover Cable Modem Adapter Modem Signal RJ-45 Pin RJ-45 Pin DB-25 Pin Signal 1. Pin 1 is connected internally to Pin 8. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-04...

  • Page 58: Console Port Mode 2 Signaling And Pinouts (Sup2 Only

    IP phone power travels over the same pairs of wires used to transmit the Ethernet signals. The IP phone voltage is completely transparent to the Ethernet signals and does not interfere with their operation. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-10 OL-10100-04...
  • Page 59 2 RD- 2 RD- 3 TD+ 3 TD+ 6 TD- 6 TD- 4 NC 4 NC 5 NC 5 NC 7 NC 7 NC 8 NC 8 NC Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-11 OL-10100-04...

  • Page 60: Fiber-Optic Connectors

    Statement 1051 The SC single-mode fiber connector is used to connect fiber-optic module ports with the external network. (See Figure B-5.) Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-12 OL-10100-04...

  • Page 61: Mt-Rj Connectors

    To disconnect the plug from the socket, press down on the raised portion on top of the plug (releasing the latch). You should hear an audible click indicating that the latch has released. Carefully pull the plug out of the socket. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-13 OL-10100-04...

  • Page 62: Lc Connectors

    When you disconnect the fiber-optic cable from the module, grip the body of the connector. Do not grip the connector jacket-sleeve. Gripping the sleeve can, over time, compromise the integrity of the fiber-optic cable termination in the LC connector. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-14 OL-10100-04...

  • Page 63: Cleaning The Fiber-Optic Connectors

    If the surface of the fiber-optic connector is not clean or does not have an even shine, repeat the process Note using a fresh surface of the alcohol pad. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-15 OL-10100-04...

  • Page 64: Lx/Lh Gbic And Mmf Cable Considerations

    984 feet (300 meters), a mode-conditioning patch cord is required. You must install the patch cord (Cisco product number CAB-GELX-625 or equivalent) between the GBIC and the MMF cable on both the transmit and receive ends of the link.

  • Page 65: Patch Cord Installation

    “To Cable Plant” into the patch panel. The patch cord is 9.84 feet (3 meters) long and has duplex SC male connectors at each end. Figure B-9 Patch Cord Installation To equipment To cable plant Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-17 OL-10100-04...
  • Page 66 Appendix B Cable and Connector Specifications LX/LH GBIC and MMF Cable Considerations Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-18 OL-10100-04...
  • Page 67 2 signaling (Sup Eng 2) B-10 console ports copy running-config command Gigabit Ethernet limitations B-4, B-5, B-6 specifications category 5e static electricity caution B-10 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide IN-1 OL-10100-04...
  • Page 68 2-13 RSP720, Sup720, Sup32 2-13 RSP720, Sup720, Sup32 2-13 STATUS 2-13, 2-15 Sup2 2-15 Sup2 2-15 SWITCH LOAD (Sup Eng 2 only) 2-16 SYSTEM 2-13, 2-16 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide IN-2 OL-10100-04...
  • Page 69 B-17 tools for installing and removing using with LX/LH GBICs B-16 Route Switch Processor 720 (RSP720) 2-13 PCMCIA CompactFlash support 3-12 See also Flash PC cards Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide IN-3 OL-10100-04...
  • Page 70 2-15 write command LEDs (table) 2-15 write-protection switch, flash memory card (figure) 3-12 uplink ports 3-11 Supervisor Engine 32 (Sup32) CompactFlash support 3-12 front panel (figure) 2-12 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide IN-4 OL-10100-04...

Table of Contents