Download Print this page

Timekeeping; Home City Settings; Current Time And Date Settings Manually - Casio 3414 Operation Manual

Hide thumbs

Advertisement

Selecting a Mode
The illustration below shows which buttons you need to press to navigate between modes.
To return to the Timekeeping Mode from any other mode, hold down D for about two seconds.
Stopwatch Mode
Stopwatch Mode
Data Recall
Data Recall
Mode
Mode
Countdown
Countdown
Timer Mode
Timer Mode
Alarm Mode
Alarm Mode
E-24
General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.
Direct Timekeeping Mode Access
To enter the Timekeeping Mode from any other mode, hold down D for about two seconds.
Auto Return Features
The watch will automatically return to the Timekeeping Mode if you do not perform any button operation
for a particular amount of time in each mode.
Mode Name
Sunrise/Sunset, Data Recall, Alarm, Receive, Digital
Compass
Altimeter
Barometer/Thermometer
Setting screen (digital setting fl ashing)
If you leave a screen with fl ashing digits on the display for two or three minutes without performing any
operation, the watch exits the setting screen automatically.
Initial Screens
When you enter the Data Recall, Alarm, World Time, or Digital Compass Mode, the data you were viewing
when you last exited the mode appears fi rst.
Scrolling
The A and C buttons are used on the setting screen to scroll through data on the display. In most
cases, holding down these buttons during a scroll operation scrolls through the data at high speed.
E-26
Confi guring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting either standard time or
daylight saving time (DST).
City code
City code
To confi gure Home City and summer time settings
PM
PM
1. In the Timekeeping Mode, hold down E for at least two seconds.
indicator
indicator
First, SET Hold will fl ash on the display, and CITY will be displayed in
the upper display. After that, the currently selected city code and city
name will scroll across the upper display. Keep E depressed until the
scrolling starts.
The watch will exit the setting mode automatically if you do not
perform any operation for about two or three minutes.
For details about city codes, see the "City Code Table" at the back
Hour :
Hour :
of this manual.
Minutes
Minutes
2. Use A (East) and C (West) to scroll through the available city codes.
DST indicator
DST indicator
Keep scrolling until the city code you want to select as your Home
City is displayed.
3. Press D to display the DST setting screen.
4. Use A to cycle through the DST settings in the sequence shown below.
Auto DST (AUTO)
Seconds
Seconds
E-28
Confi guring Current Time and Date Settings Manually
You can confi gure current time and date settings manually when the watch is unable to receive a time
calibration signal.
To change the current time and date settings manually
1. In the Timekeeping Mode, hold down E for at least two seconds.
City code
City code
First, SET Hold will fl ash on the display, and CITY will be displayed in
PM
PM
the upper display. After that, the currently selected city code and city
indicator
indicator
name will scroll across the upper display. Keep E depressed until the
scrolling starts.
Hour :
Hour :
Minutes
Minutes
E-30
Operation Guide 3414
Timekeeping Mode
Timekeeping Mode
Sunrise/Sunset
Sunrise/Sunset
Mode
Mode
World Time
World Time
Mode
Mode
Receive Mode
Receive Mode
Approximate Elapsed Time
3 minutes
1 hour minimum
12 hours maximum
1 hour
3 minutes
DST off (OFF)
DST on (ON)
You can use buttons A, B, and C to enter a sensor mode directly from the Timekeeping Mode or
from another sensor mode. To enter a sensor mode from the Sunrise/Sunset, Data Recall, Alarm,
Stopwatch, Countdown Timer, World Time, or Receive Mode, fi rst enter the Timekeeping Mode and
then press the applicable button.
Sensor Modes
Sensor Modes
Digital Compass Mode
Digital Compass Mode
Thermometer Mode
Thermometer Mode

Timekeeping

Use the Timekeeping Mode (TIME) to set and view the current time and date.
Each press of E in the Timekeeping Mode will change screen contents as shown below.
Day of the Week/Date Screen
Day of week
Day
Seconds
PM
Hour :
indicator
Minutes
The Auto DST (AUTO) setting will be available only when a city code that supports time calibration
signal reception (page E-14) is selected as the Home City. While Auto DST is selected the DST
setting will be changed automatically in accordance with time calibration signal data.
Note that you cannot switch between standard time and daylight saving time (DST) while UTC is
selected as your Home City.
5. After all of the settings are the way you want, press E twice to exit the setting screen.
Daylight Saving Time is turned on when the DST indicator is on the display.
Note
After you specify a city code, the watch will use UTC* offsets in the World Time Mode to calculate
the current time for other time zones based on the current time in your Home City.
* Coordinated Universal Time, the world-wide scientifi c standard of timekeeping.
The reference point for UTC is Greenwich, England.
Selecting some city codes automatically makes it possible for the watch to receive the time
calibration signal for the corresponding area. See page E-14 for details.
2. Press D to move the fl ashing in the sequence shown below to select the other settings.
12/24-Hour
City Code
DST
Format
Thermometer/Barometer/
Power
Illumination
Altitude display unit
Saving
Duration
The following steps explain how to confi gure timekeeping settings only.
3. When the timekeeping setting you want to change is fl ashing, use A and/or C to change it as
described below.
Screen
To do this:
Change the city code
Cycle between Auto DST (AUTO), Daylight Saving
Time (ON) and Standard Time (OFF).
Toggle between 12-hour (12H) and 24-hour (24H)
timekeeping.
Reset the seconds to 00
(If the current seconds count is between 30 and 59,
one is added to the minute count).
Change the hour or minutes
Change the year, month, or day
4. After all of the settings are the way you want, press E twice to exit the setting screen.
Barometer/
Barometer/
Altimeter Mode
Altimeter Mode
Month/Day Screen
Barometric Pressure
Graph Screen
Barometric pressure graph
Month Day
Seconds
Hour
Minutes
Button Operation
Day
Tone
Do this:
Use A (East) and C (West).
Press A.
Press A.
Press A.
Use A (+) and C (–).
E-25
E-27
E-29
Year
Month
E-31

Hide quick links:

Advertisement

loading