Marquis 660 Owner's Manual page 7

E V E R Y D A Y H O T T U B S
1. Temp +/-
2. Light: Press until "MODE" appears in the LCD display
3. Temp +/- To toggle between ready and rest options. The options will
appear in the bottom of the LCD display in small print
4. Light: To select and exit
Time
Use this function to reset or change the internal time clock. Note that this
feature is not an actual clock that will display on the panel. The clock feature
is used as a basis for running filter cycles during the correct time of the day.
To set or adjust the clock, press the listed buttons in the following sequence.
Button presses must occur within 3-5 seconds of each other.
1. Temp +/-
2. Light: Press until you see "TIME" displayed in the LCD display on the panel.
3. Temp +/- To display clock
4. Temp +/- To adjust hour (note the AM – PM indicator in the display)
5. Light: To move to minutes
6. Temp +/- To adjust minutes
7. Light: To hold and exit
"FLIP" (Invert Display)
Your spa will come preset from the factory with the display viewable from
inside the spa (recommended). The system will allow the LCD display on the
panel to invert or "FLIP" to allow reading the display from outside of the spa if
desired. To "FLIP" the display, press the listed buttons in the following
sequence. Button presses must occur within 3-5 seconds of each other.
1. Temp +/-
2. Light: Until the word "FLIP" appears in the LCD
3. Temp +/- to invert the display
4. Light: To select and exit
To return the display to the original position, follow the same sequence
Temperature Lock or Panel Lock (Unlocked is the factory default -
Recommended)
The electronic controls can be locked in two levels, temperature lock and
panel lock. Temperature lock will lock the temperature control/button only.
Panel lock will lock all of the controls and buttons on the panel. These choices
can be a useful feature to keep others from accidentally changing the settings
or operating functions available through the control panel. To engage
temperature lock, press the listed buttons in the following sequence. Button
presses must occur within 3-5 seconds of each other.
1. Temp +/-
2. Light: Until you see the word "LOCK" in the LCD display
3. Temp +/- Which will display "TEMP" on the first press. Continue pressing to
change between on and off
4. Light: To select and exit
To engage panel lock, press the listed buttons in the following sequence.
Button presses must occur within 3-5 seconds of each other.
1. Temp +/-
2. Light: Press until you see the word "LOCK" in the LCD display
3. Temp +/- to enter the menu, "TEMP" will be displayed
4. Light: To display "PANL" in LCD display
5. Temp +/- to display on/off choice
6. Light: To select and exit
To unlock either temperature or panel lock feature, use the following directions.
1. Press and hold down the Temp +/- button
2. While holding down the Temp +/- button, press the Light button two (2) times
3. The LCD display will read "UNLK" restoring the panel buttons to full
operation.
®
O W N E R ' S
Hold
This is a feature that can be used while servicing your spa such as cleaning the
spa shell or the filter. The Soak button on the panel can also perform the same
function. If you choose to use the Hold mode, press the listed buttons in the
following sequence. Button presses must occur within 3-5 seconds of each
other.
1. Temp +/-
2. Light: Press until you see "HOLD" in the LCD display.
3. Temp +/- to engage the hold mode. The panel will scroll "HOLD – ING –
FOR – 0:60" and continue to count down. LCD display will read "DONE"
4. Light: To stop and exit the hold mode at any time. LCD display will read
"DONE"
Filtration Cycles (Factory default is 2 hours one time per day)
The electronic controls will allow for additional control for up to two
independent filtration cycles to be set. This can be useful if your usage
patterns vary from light to heavy and/or you need more or less filtration time
to aid in maintaining clean water. To adjust the filtration times, press the
listed buttons in the following sequence. Button presses must occur within
3-5 seconds of each other.
1. Temp +/-
2. Light: Press until you see the word "FLTR" with a small "1" in the LCD
screen
3. Temp +/- Which will change display to "BEGN". This will be when the cycle
starts during the day or night.
4. Temp +/- To show time. Continue to press to adjust the hour in one hour
intervals
5. Light: To change the display to minutes
6. Temp +/- To change minutes in increments of 15 intervals
7. Light: To set and move to next screen which will be "RUN HRS". This is
how long the cycle will run.
8. Temp +/- To choose the number of hours you want the spa to filter in one
hour intervals
9. Light: To change the display to minutes
10. Temp +/- To choose the number of minutes you want the spa to filter in 15
minute intervals.
11. Light: To set and show end time. This will be displayed in the LCD window
as "F 1 – ENDS – TIME"
12. Light: To move on to filter cycle 2 which will be displayed in the LCD
window as "FLTR" with a small "2".
13. Temp +/- to choose on or off. If on is chosen, repeat steps 3 through 11 to
set filter cycle 2.
14. Light: To exit.
Light Timer (Factory default is off – Recommended)
The LED spa lights can be set to come on and go off at specified times
during the day or night. To set the light timer, press the listed buttons in the
following sequence. Button presses must occur within 3-5 seconds of each
other.
1. Temp +/-
2. Light: Press until you see the word "LITE TIMR" in the LCD display
3. Temp +/- To toggle between on and off
4. Light: To set and change the display to "BEGN". This is when the timer will
start.
5. Temp +/- To display hour window and change hour in increments of 1 hour
intervals
6. Light: To set and move to next screen which will be minutes.
7. Temp +/- To choose the number of minutes to run in 15 minute intervals.
8. Light: To set and display "RUN HRS" This is how long the timer will run.
M A N U A L
7