Related Manuals for Stanton T.60
Summary of Contents for Stanton T.60
- Page 1 S T A N T O N MA G N E T I C S , I N C information@stantondj.com + 1 954- 689-8833 w w w . s t a n t o n d j . c o m DJLab.2 OWNER'S MANUAL...
-
Page 2: Important Safety Instructions
8. Do not install near any heat sources such as radiators, unused for long periods of time. hear registers, stoves, or other apparatus (including 14. Refer all servicing to qualified Stanton service center. amplifiers) that produce heat. Servicing is required when the apparatus has been 9. -
Page 3: Line Voltage Selection
LINE VOLTAGE SELECTION M.201 FEATURES 3 band EQ w/ input GAIN control per channel. Power on/off muting. Long-lasting crossfader. M.201 CONTENTS... - Page 4 M.201 CONTENTS 14) Grounding post - for turntable connection. Always use this connection when using standard turntables with ground cable. (Some turntables like the T.80 / T.120 do not require grounding wire) 15) Phono Inputs – Plug your turntables in here. When these connectors are used, your signal is fed directly to the high-quality RIAA phono pre-amplifiers.
-
Page 5: Quick Setup Diagram
QUICK SETUP DIAGRAM Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all input sources. Next, connect your microphone and monitor headphones. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. -
Page 6: Specifications
SPECIFICATIONS M.201 INPUT / OUTPUT IMPEDANCE & SENSITIVITY: LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB -60dB /2.2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX. OUTPUT (THD=1%) MASTER MORE THAN +14dBV MAX PHONES MORE THAN +21dBV MAX CHANNEL BALANCE WITHIN 3dB FREQUENCY RESPONSE:... -
Page 7: Before Use
500B cartridge and headshell Read this manual carefully before using the unit Operating instructions and be sure to store the manual in a safe place RCA cables with ground wire for future reference. Target light T.60 TURNTABLE CONTENTS... - Page 8 (2) Install the cartridge to the headshell and tighten pressure of the cartridge body is 1.5-2 g. If you it with screws provided with the cartridge. use a non-Stanton cartridge, please follow that 5. Insert the headshell into the front end of the tonearm, manufacturer’s instructions.
-
Page 9: Operation
MAINTENANCE • For best results & proper care of your equipment use Stanton Vinyl Cleaner (VC-1) for your records and Stylus Cleaner Kit for styli (SC-4). • Clean the stylus periodically with a soft brush to prevent the accumulation of dust. - Page 10 SPECIFICATIONS T.60 POWER SOURCE AC 100V, 50/60Hz (For Japan) AC 110V, 60Hz (For Taiwan) AC 120V, 60Hz (For U.S.A.,Canada,Mexico) AC 220V, 50Hz (For United Arab Emirates,Chile,Argentina) AC 220V, 60Hz (For Philippines) AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel) AC 240V, 50Hz (For Australia,U.K.) POWER CONSUMPTION 7.5 Watts...
- Page 11 Stanton dealer’s return policy. Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the merchandise. Stanton's liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by Stanton from your purchase of such merchandise.
- Page 12 c u t a l o n g d o t t e d l i n e...
- Page 13 PLACE STAMP HERE Stanton Magnetics, Inc. 3000 SW 42nd Street Hollywood, FL 33312 U.S.A.
Need help?
Do you have a question about the T.60 and is the answer not in the manual?
Questions and answers