Electrical Connection - Dometic WDCVLW Installation & User Manual

INSTALLATION REQUIREMENTS
b. After positioning the washing machine, press four corners on
top cover of washing machine in sequence. If the washing
machine is not stable when being pressed, this leg must be
adjusted.
c. Ensure the positioning status of washing machine. Loosen the
lock nut with wrench and turn the leg with hand until it closely
contacts with the floor.
d. Press the leg with one hand and fasten the nut tightly to the
cabinet with wrench.
e. After being locked properly, press corners again to make
sure that they have been adjusted properly. If it is still not
stable, repeat Step B.
f. Put a level on the top cover of the washing machine from the
left, right, front and back directions. If the level bubble stay in
the center then the washing machine is level. If it not, the
washing machine is not level. The bubble direction is the
direction of higher ground surface. Then, the two legs in this direction must be lowered at
the same time until the washing machine is level. Steps B & D are repeated until machine
is level. Then the leg nuts must be tightly locked.
5. Align the bracket on the front left or right leg side and slide foot into slot until it touches the back
of the slot. The slot opening must be facing the back of the appliance. Fasten the bracket (use
flexible screw extension if needed) with screws.
FRONT
Electrical Con-
BRACKET

As the maxi-
through the unit
are using its heating function, please make sure the minimum circuit ampacity of the supply wire
is 15A.

Connect the power to a socket which is correctly installed and properly grounded.

Make sure the supply voltage is the same as that in the machine's rating label.

Power plug must match the socket and cabinet must be properly and effectively grounded.

DO NOT use multi-purpose plug or socket as extension cord.

DO NOT connect and pull out plug with wet hand.

When connecting and pulling out the plug, hold the plug tightly and then pull it out. DO NOT pull
power cord forcibly.

If power cord is damaged or has any sign of being broken, special power cord must be selected
or purchased from its manufacturer or service center for replacement.
–
To reduce the risk of fire, electric shock, or injury to persons,
REAR
BRACKET
LEG NUT
nection
mum current
is 12A when you
12
OPERATING INSTRUCTIONS

Spin Speed: The washer drum spins at up to 1200 RPM. This reduces drying time and saves
energy. Press the SPIN SPEED button until the indicator light for the desired setting is lit. Some
fabrics, such as delicates, require a slower spin speed.

Temp.: Press this button to select the temperature you need. There are four temperatures avail-
able.

Pre-wash: Select this option to add a prewash and spin cycle to the chosen cycle. This is espe-
cially useful for heavily soiled items.

Child Lock: Press the soil level and delay buttons at the same time to unlock/lock control panel.
Reference Symbols displayed on panel.
Pre-wash Wash Rinse
Washing Clothes the First Time
Before washing clothes the first time, the washing machine
must run through the complete cycle of procedures without
clothes as follows:
1. Connect power source and water.
2. Put a little liquid detergent into the box and close it.
3. Press the button "Power".
4. Press the button "Start/Pause".
The drawer is separated as follows:
I : Pre-detergent or washing powder.
II : main detergent, softener, pre-dip, bleaching or decontaminating products.
: washing additive, such as fabric softener.
Put detergent into Washing Machine.
1. Pull out the drawer.
2. Fill liquid pre-detergent into Case I (when necessary).
3. Fill liquid detergent into Case II.
4. Fill softener into Case (when necessary).
Notes:
For liquid detergents or additives, before they are poured into the detergent box, it is suggested to use
some water for dilution to prevent the inlet of detergent box from being blocked and overflowing while
filling water.
Do not use bleach. Hazardous fumes can form
Start up washing machine
Connect the power. Check if water pipes are connected properly. Open the tap completely. Put in the
clothes to be washed and fill in the detergent and fabric softener. Then press the button "Power",
Select the proper procedures and functions and press the button "Start/Pause".
Spin Drying
17