Download Print this page

American Standard Yorkville 2320 Elongated Installation Instructions

American standard 1.6 gpf two-piece pressure-assisted toilets installation instructions.
Hide thumbs
   

Advertisement

INSTALLATION INSTRUCTIONS
YORKVILLE 1.6 GPF TWO-PIECE
PRESSURE-ASSISTED TOILETS
- Model 2320 Elongated
- Model 2325 Elongated
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY
HANDLE WITH CARE!
NOTE: For proper operation these products require a minimum of 20 psi line pressure
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Neoprene or Graphite Felt Gasket
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug wall waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and perpendicular to the floor before new toilet is installed!
2
FINISHED WALL
813mm
(32)
*
222mm
(8-3/4)
C/L OF 1/2" DIA HOLES
324mm
152mm (6) CENTERS
(12-3/4)
DIMENSIONS (Nominal)
closet flange centerline (rough-in) must be 4" (102 mm)
with flange surface flush to 1/16" (16mm) max. beyond
finished wall.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 6
Adjustable Wrench
Closet FLange Set
495mm
(19-1/2)
C/L
381mm
(15)
FLEX
SUPPLY
AS REQ.
102 mm
152 mm
(4)
(6)
C/L OF
WASTE
OUTLET
152mm
(6)
NOTE: Distance from floor to
Carpenters Level
Flexible Supply Tube
3
2320
749mm
(29-1/2)
2325
803mm
(31-5/8)
FINISHED
FLOOR
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90 ° ,
and slide into place 6" (152 mm) apart and
parallel to floor. (Use putty to hold bolts in
place if necessary.) Brace under flooring as
needed and drill two mounting pilot holes as
shown.
Tape Measure
Hacksaw
(2) 5/16" Lag Bolts
CLOSET
FLUSH TO
BOLTS
1/16" (16mm)
EXPOSED
CLOSET
FLANGE
102mm
(4)
324mm
(12-3/4)
152mm
PILOT
(6)
HOLES
Saniwares
730 4 1 9 -100 R ev. D
Sealant

Advertisement

   Also See for American Standard Yorkville 2320 Elongated

   Related Manuals for American Standard Yorkville 2320 Elongated

   Summary of Contents for American Standard Yorkville 2320 Elongated

  • Page 1: Installation Instructions

    - Model 2320 Elongated - Model 2325 Elongated Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

  • Page 2

    SEALANT NEOPRENE SEAL INSTALL NEOPRENE OR GRAPHITE FELT SEAL* Install seal evenly around waste flange (horn). Apply a thin bead of sealant around base flange. * Note: Wax seal not recommended for this application. BOLT NUT & WASHER BOLT WASHER BOLT HEAD INSTALL TOILET a.

  • Page 3: Care And Cleaning

    TANK WATER INLET WASHER FLEXIBLE COUPLING NUT SUPPLY VALVE NUT COMPRESSION COLLAR TRIM PLATE VALVE CONNECT WATER SUPPLY a. Connect water supply line between shutoff valve and tank water inlet fitting. Tighten coupling nuts securely. b. Turn on supply valve and allow flushometer tank to fill.

  • Page 4: Troubleshooting Guide

    For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address: In the United States: American Standard Inc., P.O. Box 6820 Piscataway, New Jersey 08855...

This manual also for:

Yorkville 2325 elongated

Comments to this Manuals

Symbols: 0
Latest comments: