Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
For Two-Piece Toilets with
Repertoire 2266/2280
Heritage 2176
Antiquity 2262/2264
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
b.
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must
be as listed below:
FINISHED WALL
A
4
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 1 9 9 9
Ellisse 2184
Infinity 2316/2319
Cascada 2321/2323
For 4110 Tanks: A = 254mm (10")
For 4114 Tanks: A = 356mm (14")
For all other Tanks: A = 305mm (12")
SUPPLY
AS
REQ'D.
FINISHED
FLOOR
WAX RING
Adjustable Wrench
Sealant
Flexible Supply Tube
Closet Bolts
3
5
POSITION TOILET ON FLANGE
a.
Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b.
Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP" must face up!
Cadet 2798/2898
Reminiscence 2311
Cadet Specifier 2783/2883
Tape Measure
Carpenters Level
CLOSET FLANGE
CLOSET BOLTS
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90 , and slide
into place 6" (152 mm) apart and parallel to wall.
NUT
CLOSET
BOLT
FLANGE
™
2000
A
TAPERED
WASHER
Saniwares
730451 -1 0 0 Re v. A
Advertisement
Related Manuals for American Standard Antiquity 2262
Summary of Contents for American Standard Antiquity 2262
-
Page 1: Installation Instructions
Heritage 2176 Antiquity 2262/2264 Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. - Page 2 BOLT CAP CLOSET FLANGE CLOSET BOLT WASHER INSTALL TOILET Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! Install caps on washers.
- Page 3 WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite).
- Page 4 For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address: In the United States: American Standard Inc., P.O. Box 6820 Piscataway, New Jersey 08855...