American Standard Williamsburg 7391.224 Installation Instructions

Williamsburg
BIDET FITTING
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN
WITH CLEAR WATER. DRY WITH A SOFT
COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS,
ACID, POLISH, ABRASIVES, HARSH CLEANERS,
OR A CLOTH WITH A COARSE SURFACE.
1
BIDET FAUCET INSTALLATION
Turn off hot and cold water
CAUTION
supplies before beginning.
Place MOUNTING NUTS (1) onto the VALVE BODIES
(2) and insert VALVE BODIES (2) through outside
holes, from underside of the BIDET LEDGE. Drop the
RUBBER RING (3) over the VALVE BODIES (2) and
screw on the ESCUTCHEON (4) until it locks against
the internal stop.
Tighten the MOUNTING NUT (1) to secure the
VALVE BODY (2).
Remove MOUNTING NUT (9) and UPPER GASKET (7)
from TRANSFER VALVE (8) and insert into the center
forward hole of BIDET.
Replace UPPER GASKET (7). Position the side threaded
outlet rearward and secure MOUNTING NUT (9).
Thread ESCUTCHEON (5) onto TRANSFER VALVE (8)
until it seats against the BIDET LEDGE.
5
4
3
BIDET
LEDGE
HOT
1
Installation
Instructions
T M
Roughing-in Dimensions
TRANSFER VALVE (FOR FLUSHING
RIM OR SPRAY)
BIDET OUTLINE
7/8 DIA.
IS SYMBOLIC
ADJ. 1-1/4
DOUCHE SPRAY
TO 2-1/4
1-3/8
3-7/8
DIA.
5-1/2
2
DRAIN INSTALLATION
Assemble O-RING (1), WASHER (2), PIVOT ROD (3)
and NUT (4) to DRAIN BODY (5). Concave side
of cup WASHER (2) is toward ball.
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY (5).
Apply a bead of PUTTY to underside
of FLANGE (9).
Feed DRAIN BODY (5) up through BIDET
and thread FLANGE (9) fully onto
BODY (5).
Tighten LOCKNUT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back
of the BIDET.
Push DRAIN ESCUTCHEON (10) onto
TAILPIECE (11).
9
3
Assemble SPRAY BODY (1) to BIDET.
Using putty, seal underside of SPRAY
BODY FLANGE (2) and secure with
2
NUT (3).
Screw SPRAY HOSE (4) with SEAL
COLD
WASHER (5) to SPRAY BODY (1).
Connect other end of HOSE (4) with
7
SEAL WASHER (5) to side outlet
NIPPLE (6) of the TRANSFER VALVE (7).
8
Screw SPRAY CAP (8) onto SPRAY BODY (1).
7391.229
7391.224
1-3/16 DIA.
2-1/8
1-1/4 MAX.
DIA.
FINISHED
WALL
1-1/4 O.D. TAILPIECE
SPRAY INSTALLATION
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
8 TO 12
DIVERTER AND
VACUUM BREAKER
ASSEMBLY
2-1/4
(C) (H)
DIA.
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
FINISHED REAR VIEW WITH
WALL REMOVED
FLOOR
STOPPER
PUTTY
8
7
2
6
5
2
7
PUTTY
6
7
5
M 9 6 8 0 3 2 A
4-1/4
9
BIDET
CLIP
4
3
1
11
10
8
1
3
5
4